Skip to content

AiRuiChen/crazyflie_ros

Repository files navigation

crazyflie_ros

ROS stack for Bitcraze Crazyflie (http://www.bitcraze.se/), with the following features:

  • Support for Crazyflie 1.0 and Crazyflie 2.0 (using stock firmware)
  • Publishes on-board sensors in ROS standard message formats
  • Supports ROS parameters to reconfigure crazyflie parameters
  • Support for using multiple Crazyflies with a single Crazyradio
  • Includes external controller for waypoint navigation (if motion capture system is available)
  • No dependency to the Bitcraze SDK (Driver and Controller written in C++)

Installation

Clone the package into your catkin workspace:

git clone https://github.com/whoenig/crazyflie_ros.git

If you want to use joystick teleoperation, you should setup the hector_quadrotor package (http://wiki.ros.org/hector_quadrotor).

Usage

There are four packages included: crazyflie, crazyflie_description, crazyflie_controller, and crazyflie_demo.

Crazyflie_driver

This package contains the driver. In order to support multiple Crazyflies with a single Crazyradio, there is crazyflie_server (communicating with all Crazyflies) and crazyflie_add to dynamically add Crazyflies. The server does not communicate to any Crazyflie initially, hence crazyflie_add needs to be used.

Crazyflie_description

This package contains a 3D model of the Crazyflie (1.0). This is for visualization purposes in rviz.

Crazyflie_controller

This package contains a simple PID controller for hovering or waypoint navigation. It can be used with external motion capture systems, such as VICON.

Crazyflie_demo

This package contains a rich set of examples to get quickly started with the Crazyflie.

For teleoperation using a joystick, use:

roslaunch crazyflie_demo teleop_xbox360.launch uri:=radio://0/100/2M

where the uri specifies the uri of your Crazyflie.

For hovering at (0,0,1) using VICON, use:

roslaunch crazyflie_demo hover_vicon.launch uri:=radio://0/100/2M frame:=/vicon/crazyflie/crazyflie x:=0 y:=0 z:=1

where the uri specifies the uri of your Crazyflie and frame the tf-frame. The launch file runs vicon_bridge automatically.

For multiple Crazyflies make sure that all Crazyflies have a different address. Crazyflies which share a dongle should use the same channel and datarate for best performance. The performance degrades with the number of Crazyflies per dongle due to bandwidth limitations, however it was tested successfully to use 3 CFs per Crazyradio.

roslaunch crazyflie_demo multi_teleop_xbox360.launch uri1:=radio://0/100/2M/E7E7E7E7E7 uri2:=radio://0/100/2M/E7E7E7E705

Please check the launch files in the crazyflie_demo package for other examples, including simple waypoint navigation.

ROS Features

Parameters

The launch file supports the following arguments:

  • uri: Specifier for the crazyflie, e.g. radio://0/80/2M
  • tf_prefix: tf prefix for the crazyflie frame(s)
  • roll_trim: Trim in degrees, e.g. negative if flie drifts to the left
  • pitch_trim: Trim in degrees, e.g. negative if flie drifts forward

See http://wiki.bitcraze.se/projects:crazyflie:userguide:tips_and_tricks for details on how to obtain good trim values.

Subscribers

cmd_vel

Similar to the hector_quadrotor, package the fields are used as following:

  • linear.y: roll [e.g. -30 to 30 degrees]
  • linear.x: pitch [e.g. -30 to 30 degrees]
  • angular.z: yawrate [e.g. -200 to 200 degrees/second]
  • linear.z: thrust [10000 to 60000 (mapped to PWM output)]

Publishers

imu

  • sensor_msgs/IMU
  • contains the sensor readings of gyroscope and accelerometer
  • The covariance matrices are set to unknown
  • orientation is not set (this could be done by the magnetometer readings in the future.)
  • update: 10ms (time between crazyflie and ROS not synchronized!)
  • can be viewed in rviz

temperature

magnetic_field

  • sensor_msgs/MagneticField
  • update: 100ms (time between crazyflie and ROS not synchronized!)

pressure

  • Float32
  • hPa (or mbar)
  • update: 100ms (time between crazyflie and ROS not synchronized!)

battery

  • Float32
  • Volts
  • update: 100ms (time between crazyflie and ROS not synchronized!)

Similar Projects

Notes

  • The dynamic_reconfigure package (http://wiki.ros.org/dynamic_reconfigure/) seems like a good fit to map the parameters, however it has severe limitations:
    • Changed-Callback does not include which parameter(s) were changed. There is only a notion of a level which is a simple bitmask. This would cause that on any parameter change we would need to update all parameters on the Crazyflie.
    • Parameters are statically generated. There are hacks to add parameters at runtime, however those might not work with future versions of dynamic_reconfigure.
    • Groups not fully supported (ros-visualization/rqt_common_plugins#162; This seems to be closed now, however the Indigo binary packages did not pick up the fixes yet).

About

ROS Driver for Bitcraze Crazyflie

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages

  • C++ 72.7%
  • CMake 14.5%
  • Python 12.8%