Skip to content

An ESP8266 based RS232 <-> WiFi modem with Hayes AT style commands and LED indicators

License

Notifications You must be signed in to change notification settings

BenMtl/RetroWiFiModem

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

19 Commits
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

Retro WiFi modem

An ESP8266 based RS232 <-> WiFi modem with Hayes AT style commands and LED indicators

Front Panel

This project grew out of a desire to get an old Ampro LB+/Z80 hooked up to the Internet.

Right from the start, I knew I wanted a row of LED indicators at the front of the modem so that it would be reminiscent of an old Hayes Smartmodem. (I briefly considered finding an old Smartmodem on eBay, but soon remembered that the case had in fact been made of metal; they don't build 'em like that anymore.)

Since the modem was going to be hooked up to the Little Board's serial port, I needed an actual RS-232 level serial port, with either a DB-25 or DE-9 connector.

And finally, since I wanted the Hayes style LEDs, I thought it would be handy to have the Hayes AT commands too, at least as close as I could manage.

That was all I started with. I couldn't tell you how I stumbled across the whole WiFi modem thing; I can't even remember what terms I searched with but very quickly I came across the message thread at WiFi232's Evil Clone. Inspired by that, and Paul Rickards' WiFi232, and Daniel Jameson's ESP8266 based virtual modem I got started.

I had a preliminary version put together and working by the first evening. Then the wholesale changes to the software began. And for the longest time, it looked like they'd never end. Eventually though, they calmed down and "wholesale changes" downshifted to "another tweak I'd like to make."

The hardware didn't change nearly as much from beginning to end. I did the development on a Wemos D1 R1 and a little half length solderless breadboard mounted together. The plan for the final hardware was always to use a Wemos D1 mini. A MAX3232 took care of the 3.3V <-> RS-232 level shifting, and a 74HCT245 was used to drive the indicator LEDs.

The only major addition to the hardware during development was an OR gate on the serial output from the ESP8266. On startup, the ESP8266 sends out some debug information (at an oddball baud rate) through the serial port. It shows up as garbage characters to whatever's hooked up to the serial port. It annoyed me enough that I fed the Tx signal through the OR gate, with the other input hooked up to an output pin that I could count on remaining high (thereby masking off the Tx signal) until after the sketch had started and set it low.

Status

Is a personal project like this ever really finished? I've finished the first complete unit and while I don't expect the hardware to change (much), the software is a completely different story. I expect to be tweaking and adding to that for some time to come. However, it's completely usable at the moment.

The Hardware

Interior

I made the decision to use through hole components throughout; retro components for a retro modem. Besides, I already had most of them in my parts box!

In keeping with the retro theme, the modem uses classic Hayes style blinking LEDs and a DE-9F for the RS-232 connector. Everything is displayed: RTS, CTS, DSR, DTR, DCD, RI, TxD and RxD. However, only RxD, TxD, RTS and CTS are actually brought out on the DE-9F connector. The Ampro LB only brought those four signals out so it would have been overkill for the modem I was designing for it to support anything more. Additionally, it would have required another three MAX3232 ICs to do it (had the MAX3237 been available in DIP, I might have had a harder time saying no...).

The PCB is laid out for a Wemos D1 mini and the software expects to see just that. If you're just using the software and not the PCB, there's no reason you couldn't use another kind of ESP8266 board; I used a D1 R1 myself when I was developing the modem. You'd just need to add pin definitions for your board in RetroWiFiModem.h.

A separate 3.3V regulator is used to power the MAX3232 IC and 74HC32 quad OR gate. Some (most?) D1 mini clones have the smallest 3.3V regulator on board that they can get away with to power the board, and they don't have a lot of mA's left over to power anything else. Better safe than sorry.

Back Panel

The power connector expects a 2.1mm I.D. x 5.5mm O.D. barrel plug, delivering 5 volts, centre positive. I used a Tri-Mag L6R06H-050 (5V, 1.2A), DigiKey part# 364-1251-ND. If you plug in a 9V adapter like you'd use for an Arduino, you will let the magic smoke out and have an ex-modem on your hands.

Schematic

On the off chance that there's someone else out there with a well stocked parts box and a burning desire to put together their own WiFi modem, there's a BOM in the kicad sub directory. If you actually had to go out and buy all the parts, it really wouldn't be cost effective.

Then again, how practical is getting an Ampro Little Board on the Internet? Practicality isn't always everything. Sometimes nostalgia is worth the effort.

Didn't make the cut

I have to admit that I semi-seriously considered adding one of those little audio playback modules for faux dialing and connection sounds. It would have been in keeping with the whole retro theme. But in the end I decided not to. Maybe next time.

The case

Like I said as the start, I would have loved to have used an old Hayes Smartmodem case, but they were metal and wouldn't have allowed the WiFi to work particularly well.

In the end I went with a Hammond 1593N case (DigiKey part # HM963-ND or HM964-ND depending on whether you like black or grey). STL and OpenSCAD files are included for the front and back panels. You could use the proper Hammond red panel for the front (DigiKey part # HM965-ND), but they're only available in 10 packs and their price is highway robbery. I ended up using a slightly smaller red panel (DigiKey part # HM889-ND) that was much cheaper and available in single units.

The PCB

The PCB includes cutouts for the two columns that join the case together, and mounting holes for the 6 standoffs. Also, there's an oddly shaped cutout in back end to allow a particular IDC DE-9F I had on hand. It's available from DigiKey (or a very close clone is) but it's fairly pricey. But there's plenty of room for an ordinary solder cup DE-9F. You'd most likely want to omit the 10 pin header and just wire the DE-9F right to the board.

You might notice that the vias are unusually large by today's standards. The reason for that is to allow the option of constructing the PCB as a single sided board, replacing the top layer of copper with 11 jumpers.

The Software

In a nod to its popularity, the command set I used largely follows that used in Paul Rickards' WiFi232 modem. Even if the innards are completely different, it made sense to make it work like what people where already used to. There's a reason everyone's been copying the Hayes command set for almost 40 years!

First time setup

The default serial configuration is 1200bps, 8 data bits, no parity, 1 stop bit.

Here's the commands you need to set up the modem to automatically connect to your WiFi network:

  1. AT$SSID=your WiFi network name to set the WiFi network that the modem will connect to when it powers up.
  2. AT$PASS=your WiFi network password to set the password for the network.
  3. ATC1 to connect to the network.
  4. Optional stuff:
    • AT$SB=speed to set the default serial speed.
    • AT$SU=dps to set the data bits, parity and stop bits.
    • ATNETn to select whether or not to use Telnet protocol.
    • AT&kn to use RTS/CTS flow control.
  5. AT&W to save the settings.

Once you've done that, the modem will automatically connect to your WiFi network on power up and will be ready to "dial up" a connection with ATDT.

Command Reference

Multiple AT commands can be typed in on a single line. Spaces between commands are allowed, but not within commands (i.e. AT S0=1 X1 Q0 is fine; ATS 0= 1 is not). Commands that take a string as an argument (e.g. AT$SSID=, AT$TTY=) assume that everything that follows is a part of the string, so no commands are allowed after them.

Command Details
+++ Online escape code. Once your modem is connected to another device, the only command it recognises is an escape code of a one second pause followed by three typed plus signs and another one second pause, which puts the modem back into local command mode.
A/ Repeats the last command entered. Do not type AT or press Enter.
AT The attention prefix that precedes all command except A/ and +++.
AT? Displays a help cheatsheet.
ATA Force the modem to answer an incoming connection when the conditions for auto answer have not been satisfied.
ATC?
ATCn
Query or change the current WiFi connection status. A result of 0 means that the modem is not connected to WiFi, 1 means the modem is connected. The command ATC0 disconnects the modem from a WiFi connection. ATC1 connects the modem to the WiFi.
ATDSn Calls the host specified in speed dial slot n (0-9).
ATDT [+=-]host[:port] Tries to establish a WiFi TCP connection to the specified host name or IP address. If no port number is given, 23 (Telnet) is assumed. You can also use ATDT to dial one of the speed dial slots in one of two ways:

  • The alias in each speed dial slot is checked to see if it matches the specified hostname.
  • A host specified as 7 identical digits dials the slot indicated by the digit. (i.e. 2222222 would speed dial the host in slot 2).

Preceding the host name or IP address with a +, = or - character overrides the ATNET setting for the period of the connection. + forces NET2; = forces NET1, and - forces NET0.
ATE?
ATEn
Command mode echo. Enables or disables the display of your typed commands.

  • E0 Command mode echo OFF. Your typing will not appear on the screen.
  • E1 Command mode echo ON. Your typing will appear on the screen.
ATGEThttp://host[/page] Displays the contents of a website page. https connections are not supported. Once the contents have been displayed, the connection will automatically terminate.
ATH Hangs up (ends) the current connection.
ATI Displays the current network status, including sketch build date, WiFi and call connection state, SSID name, IP address, and bytes transferred.
ATNET?
ATNETn
Query or change whether telnet protocol is enabled. A result of 0 means that telnet protocol is disabled; 1 is Real telnet protocol and 2 is Fake telnet protocol. If you are connecting to a telnet server, it may expect the modem to respond to various telnet commands, such as terminal name (set with AT$TTY), terminal window size (set with AT$TTS) or terminal speed. Telnet protocol should be enabled for these sites, or you will at best see occasional garbage characters on your screen, or at worst the connection may fail.

The difference between real and fake telnet protocol is this: with real telnet protocol, a carriage return (CR) character being sent from the modem to the telnet server always has a NUL character added after it. The implementation of the telnet protocol used by some BBSes doesn't properly strip out the NUL character. When connecting to such BBSes (Particles! is one), use fake telnet.

When using real telnet protocol, when the telnet server sends a CR character followed by a NUL character, only the CR character will be sent to the serial port; the NUL character will be silently stripped out. With fake telnet protocol, the NUL will be passed through.
ATO Return online. Use with the escape code (+++) to toggle between command and online modes.
ATQ?
ATQn
Enable or disable the display of result codes. The default is Q0.

  • Q0 Display result codes.
  • Q1 Suppress result codes (quiet).
ATRD
ATRT
Displays the current UTC date and time from NIST in the format YY-MM-DD HH:MM:SS. A WiFi connection is required and you cannot be connected to another site.
ATS0?
ATS0=n
Display or set the number of "rings" before answering an incoming connection. Setting S0=0 means "don't answer".
ATV?
ATVn
Display result codes in words or numbers. The default is V1.

  • V0 Display result codes in numeric form.
  • V1 Display result codes in text form.
ATX?
ATXn
Control the amount of information displayed in the result codes. The default is X1 (extended codes).

  • X0 Display basic codes (CONNECT, NO CARRIER)
  • X1 Display extended codes (CONNECT speed, NO CARRIER (connect time))
ATZ Resets the modem.
AT&F Reset the NVRAM contents and current settings to the sketch defaults. All settings, including SSID name, password and speed dial slots are affected.
AT&K?
AT&Kn
Data flow control. Prevents the modem's buffers for received and transmitted from overflowing.

  • &K0 Disable data flow control.
  • &K1 Use hardware flow control. Requires that your computer and software support Clear to Send (CTS) and Request to Send (RTS) at the RS-232 interface.
AT&R?
AT&R=server pwd
Query or change the password for incoming connections. If set, the user has 3 chances in 60 seconds to enter the correct password or the modem will end the connection.
AT&Vn Display current or stored settings.

  • &V0 Display current settings.
  • &V1 Display stored settings.
AT&W Save current settings to NVRAM.
AT&Zn?
AT&Zn=host[:port],alias
Store up to 10 numbers in NVRAM, where n is the position 0-9 in NVRAM, and host[:port] is the host string, and alias is the speed dial alias name. The host string may be up to 50 characters long, and the alias string may be up to 16 characters long.

Example: AT&Z2=particlesbbs.dyndns.org:6400,particles

This number can then be dialled in any of the following ways:

  • ATDS2
  • ATDTparticles
  • ATDT2222222
AT$AE?
AT$AE=startup AT cmd
Query or change the command line to be executed when the modem starts up.
AT$BM?
AT$BM=server busy msg
Query or change a message to be returned to an incoming connection if the modem is busy (i.e. already has a connection established).
AT$MDNS
AT$MDNS=mDNS name
Query or change the mDNS network name (defaults to "espmodem"). When a non zero TCP port is defined, you can telnet to that port with telnet mdnsname.local port.
AT$PASS?
AT$PASS=WiFi pwd
Query or change the current WiFi password. The password is case sensitive. Clear the password by issuing the set command with no password. The maximum length of the password is 64 characters.
AT$SB?
AT$SB=n
Query or change the current baud rate. Valid values for "n" are 110, 300, 450, 600, 710, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 76800 and 115200. Any other value will return an ERROR message. The default baud rate is 1200. The Retro WiFi modem does not automatically detect baud rate like a dialup modem. The baud rate setting must match that of your terminal to operate properly. It will display garbage in your terminal otherwise.
AT$SP?
AT$SP=n
TCP server port to listen on. A value of 0 means that the TCP server is disabled, and no incoming connections are allowed.
AT$SSID?
AT$SSID=ssid name
Query or change the current SSID to the specified name. The given SSID name is case sensitive. Clear the SSID by issuing the set command with no SSID. The maximum length of the SSID name is 32 characters.
AT$SU?
AT$SU=dps
Query or change the current number of data bits ('d'), parity ('p') and stop bits ('s") of the serial UART. Valid values for 'd' are 5, 6, 7 or 8 bits. Valid values for 'p' are (N)one, (O)dd or (E)ven parity. Valid values for 's' are 1 or 2 bits. The default settings are 8N1. The UART setting must match your terminal to work properly.
AT$TTL?
AT$TTL=telnet location
Query or change the Telnet location value to be returned when the Telnet server issues a SEND-LOCATION request. The default value is "Computer Room".
AT$TTS?
AT$TTS=WxH
Query or change the window size (columns x rows) to be returned when the Telnet server issues a NAWS (Negotiate About Window Size) request. The default value is 80x24.
AT$TTY?
AT$TTY=terminal type
Query or change the terminal type to be returned when the Telnet server issues a TERMINAL-TYPE request. The default value is "ansi".
AT$W?
AT$W=n
Startup wait.

  • $W=0 Startup with no wait.
  • $W=1 Wait for the return key to be pressed at startup.

Updating the Software

While I liked the idea of being able to update the software OTA, it seemed to make more sense in my situation to be able to push a new version as I built it rather than have the modem pull it. So that's what I did. It uses the default OTA upload capability built into the Arduino IDE.

RTS/CTS handshaking and a dead spin loop issue

Something I noticed with ESP8266 software that puzzled me was the number of places I saw a series of Serial print statements being broken up with calls to yield(), like so:

   Serial.print("Hello world!\n");
   yield();
   Serial.print("How are you today?\n");
   yield();

It didn't take long to figure out what was going on; The print() call was blocking, and at lower baud rates, even printing a few relatively short strings was enough to cause the watchdog to bark and cause a reset. So the repetitive yield() calls were an attempt to feed the watchdog often enough to keep it from barking.

What does this have to do with RTS/CTS handshaking? Simply put, lowering RTS for more than a few seconds was causing the watchdog to bark as well. So I started digging.

In cores/esp8266/uart.cpp I found the following function:

static void
uart_do_write_char(const int uart_nr, char c)
{
    while(uart_tx_fifo_full(uart_nr));

    USF(uart_nr) = c;
}

This is the low level function that everything calls to send a character out the serial port. The cause of the watchdog barking is in the dead spin while loop. It waits until there's room in the transmit FIFO to add another character. So if RTS/CTS handshaking is enabled, and RTS is low for longer than the watchdog likes: woof.

What I did to quiet the watchdog down both when sending long strings at low baud rates and during long waits for RTS to come active again was to add a yield() call to the dead spin while loop, like so:

static void
uart_do_write_char(const int uart_nr, char c)
{
    while(uart_tx_fifo_full(uart_nr))
      yield();

    USF(uart_nr) = c;
}

This way, no matter how long the code has to wait for space in the transmit FIFO, the watchdog is kept well fed and quiet.

References

Acknowledgements

  • A whole lot of people owe a big vote of thanks to Jussi Salin for releasing their virtual modem code for the ESP8266 and starting the ball rolling.
  • Paul Rickards for an amazing bit of hardware to draw inspiration from.
  • All the Stardot contributors for their work.
  • And, of course, Dennis C. Hayes for creating something so simple and elegant that has stood the test of time.

About

An ESP8266 based RS232 <-> WiFi modem with Hayes AT style commands and LED indicators

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages

  • C 82.6%
  • C++ 13.9%
  • OpenSCAD 3.5%