-
-
Notifications
You must be signed in to change notification settings - Fork 101
/
generic-mellow-fly-gemini-v2.cfg
161 lines (136 loc) · 3.17 KB
/
generic-mellow-fly-gemini-v2.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
# This file contains common pin mappings for the Mellow Fly-Gemini-v2.
# To use this config, the firmware should be compiled for the
# STM32F405 with a "32KiB bootloader".
# The "make flash" command does not work on the Fly-Gemini-v2. Instead,
# after running "make", copy the generated "out/klipper.bin" file to a
# file named "firmware.bin" or "klipper.bin" on an SD card and then restart the Fly-Gemini-v2
# with that SD card.
# See docs/Config_Reference.md for a description of parameters.
[stepper_x]
step_pin: PC13
dir_pin: PC1
enable_pin: !PB2
microsteps: 16
rotation_distance: 40
endstop_pin: ^PA3
position_endstop: 0
position_max: 200
homing_speed: 50
[stepper_y]
step_pin: PC14
dir_pin: !PC4
enable_pin: !PD2
microsteps: 16
rotation_distance: 40
endstop_pin: ^PB1
position_endstop: 0
position_max: 200
homing_speed: 50
[stepper_z]
step_pin: PC15
dir_pin: PC5
enable_pin: !PC12
microsteps: 16
rotation_distance: 40
endstop_pin: ^PB10
position_endstop: 0.5
position_max: 200
[extruder]
step_pin: PC3
dir_pin: PC8
enable_pin: !PC11
microsteps: 16
rotation_distance: 33.500
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PA0
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC0
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
max_temp: 250
[heater_bed]
heater_pin: PA2
sensor_type: Generic 3950
sensor_pin: PC2
control: watermark
min_temp: 0
max_temp: 130
[fan]
pin: PC6
#FAN1
#[heater_fan fan1]
#pin: PC7
[mcu]
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100
########################################
# TMC2209 configuration
########################################
#[tmc2209 stepper_x]
#uart_pin: PB11
#run_current: 0.800
#diag_pin: PA3
#stealthchop_threshold: 999999
#[tmc2209 stepper_y]
#uart_pin: PB9
#run_current: 0.800
#diag_pin: PB1
#stealthchop_threshold: 999999
#[tmc2209 stepper_z]
#uart_pin: PB8
#run_current: 0.800
#diag_pin: PB10
#stealthchop_threshold: 999999
#[tmc2209 extruder]
#uart_pin: PB7
#run_current: 0.600
#diag_pin:
#stealthchop_threshold: 999999
########################################
# TMC5160 configuration
########################################
#[tmc5160 stepper_x]
#cs_pin: PB11
#spi_bus: spi1
#run_current: 0.800
#diag1_pin: PA3
#stealthchop_threshold: 999999
#[tmc5160 stepper_y]
#cs_pin: PB9
#spi_bus: spi1
#run_current: 0.800
#diag1_pin: PB1
#stealthchop_threshold: 999999
#[tmc5160 stepper_z]
#cs_pin: PB8
#spi_bus: spi1
#run_current: 0.800
#diag1_pin: PB10
#stealthchop_threshold: 999999
#[tmc5160 extruder]
#cs_pin: PB7
#spi_bus: spi1
#run_current: 0.800
#diag1_pin:
#stealthchop_threshold: 999999
########################################
# EXP1 / EXP2 (display) pins
########################################
[board_pins]
aliases:
# EXP1 header
EXP1_1=PC9, EXP1_3=PA13, EXP1_5=PA9, EXP1_7=<NC>, EXP1_9=<GND>,
EXP1_2=PB6, EXP1_4=PA10, EXP1_6=PA8, EXP1_8=<NC>, EXP1_10=<5V>,
# EXP2 header
EXP2_1=PB14, EXP2_3=PA15, EXP2_5=PA14, EXP2_7=PC10, EXP2_9=<GND>,
EXP2_2=PB13, EXP2_4=PB12, EXP2_6=PB15, EXP2_8=<RST>, EXP2_10=<NC>,
# See the sample-lcd.cfg file for definitions of common LCD displays.