forked from ArduPilot/ardupilot
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathParameters.cpp
1167 lines (1002 loc) · 50.1 KB
/
Parameters.cpp
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
#include "Copter.h"
/*
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
/*
* ArduCopter parameter definitions
*
*/
#define GSCALAR(v, name, def) { copter.g.v.vtype, name, Parameters::k_param_ ## v, &copter.g.v, {def_value : def} }
#define ASCALAR(v, name, def) { copter.aparm.v.vtype, name, Parameters::k_param_ ## v, (const void *)&copter.aparm.v, {def_value : def} }
#define GGROUP(v, name, class) { AP_PARAM_GROUP, name, Parameters::k_param_ ## v, &copter.g.v, {group_info : class::var_info} }
#define GOBJECT(v, name, class) { AP_PARAM_GROUP, name, Parameters::k_param_ ## v, (const void *)&copter.v, {group_info : class::var_info} }
#define GOBJECTPTR(v, name, class) { AP_PARAM_GROUP, name, Parameters::k_param_ ## v, (const void *)&copter.v, {group_info : class::var_info}, AP_PARAM_FLAG_POINTER }
#define GOBJECTVARPTR(v, name, var_info_ptr) { AP_PARAM_GROUP, name, Parameters::k_param_ ## v, (const void *)&copter.v, {group_info_ptr : var_info_ptr}, AP_PARAM_FLAG_POINTER | AP_PARAM_FLAG_INFO_POINTER }
#define GOBJECTN(v, pname, name, class) { AP_PARAM_GROUP, name, Parameters::k_param_ ## pname, (const void *)&copter.v, {group_info : class::var_info} }
const AP_Param::Info Copter::var_info[] = {
// @Param: SYSID_SW_MREV
// @DisplayName: Eeprom format version number
// @Description: This value is incremented when changes are made to the eeprom format
// @User: Advanced
// @ReadOnly: True
GSCALAR(format_version, "SYSID_SW_MREV", 0),
// @Param: SYSID_THISMAV
// @DisplayName: MAVLink system ID of this vehicle
// @Description: Allows setting an individual MAVLink system id for this vehicle to distinguish it from others on the same network
// @Range: 1 255
// @User: Advanced
GSCALAR(sysid_this_mav, "SYSID_THISMAV", MAV_SYSTEM_ID),
// @Param: SYSID_MYGCS
// @DisplayName: My ground station number
// @Description: Allows restricting radio overrides to only come from my ground station
// @Values: 255:Mission Planner and DroidPlanner, 252: AP Planner 2
// @User: Advanced
GSCALAR(sysid_my_gcs, "SYSID_MYGCS", 255),
// @Param: PILOT_THR_FILT
// @DisplayName: Throttle filter cutoff
// @Description: Throttle filter cutoff (Hz) - active whenever altitude control is inactive - 0 to disable
// @User: Advanced
// @Units: Hz
// @Range: 0 10
// @Increment: .5
GSCALAR(throttle_filt, "PILOT_THR_FILT", 0),
// @Param: PILOT_TKOFF_ALT
// @DisplayName: Pilot takeoff altitude
// @Description: Altitude that altitude control modes will climb to when a takeoff is triggered with the throttle stick.
// @User: Standard
// @Units: cm
// @Range: 0.0 1000.0
// @Increment: 10
GSCALAR(pilot_takeoff_alt, "PILOT_TKOFF_ALT", PILOT_TKOFF_ALT_DEFAULT),
// @Param: PILOT_TKOFF_DZ
// @DisplayName: Takeoff trigger deadzone
// @Description: Offset from mid stick at which takeoff is triggered
// @User: Standard
// @Range: 0 500
// @Increment: 10
GSCALAR(takeoff_trigger_dz, "PILOT_TKOFF_DZ", THR_DZ_DEFAULT),
// @Param: PILOT_THR_BHV
// @DisplayName: Throttle stick behavior
// @Description: Bitmask containing various throttle stick options. TX with sprung throttle can set PILOT_THR_BHV to "1" so motor feedback when landed starts from mid-stick instead of bottom of stick.
// @User: Standard
// @Values: 0:None,1:Feedback from mid stick,2:High throttle cancels landing,4:Disarm on land detection
// @Bitmask: 0:Feedback from mid stick,1:High throttle cancels landing,2:Disarm on land detection
GSCALAR(throttle_behavior, "PILOT_THR_BHV", 0),
// @Group: SERIAL
// @Path: ../libraries/AP_SerialManager/AP_SerialManager.cpp
GOBJECT(serial_manager, "SERIAL", AP_SerialManager),
// @Param: TELEM_DELAY
// @DisplayName: Telemetry startup delay
// @Description: The amount of time (in seconds) to delay radio telemetry to prevent an Xbee bricking on power up
// @User: Advanced
// @Units: s
// @Range: 0 30
// @Increment: 1
GSCALAR(telem_delay, "TELEM_DELAY", 0),
// @Param: GCS_PID_MASK
// @DisplayName: GCS PID tuning mask
// @Description: bitmask of PIDs to send MAVLink PID_TUNING messages for
// @User: Advanced
// @Values: 0:None,1:Roll,2:Pitch,4:Yaw
// @Bitmask: 0:Roll,1:Pitch,2:Yaw
GSCALAR(gcs_pid_mask, "GCS_PID_MASK", 0),
#if MODE_RTL_ENABLED == ENABLED
// @Param: RTL_ALT
// @DisplayName: RTL Altitude
// @Description: The minimum alt above home the vehicle will climb to before returning. If the vehicle is flying higher than this value it will return at its current altitude.
// @Units: cm
// @Range: 200 8000
// @Increment: 1
// @User: Standard
GSCALAR(rtl_altitude, "RTL_ALT", RTL_ALT),
// @Param: RTL_CONE_SLOPE
// @DisplayName: RTL cone slope
// @Description: Defines a cone above home which determines maximum climb
// @Range: 0.5 10.0
// @Increment: .1
// @Values: 0:Disabled,1:Shallow,3:Steep
// @User: Standard
GSCALAR(rtl_cone_slope, "RTL_CONE_SLOPE", RTL_CONE_SLOPE_DEFAULT),
// @Param: RTL_SPEED
// @DisplayName: RTL speed
// @Description: Defines the speed in cm/s which the aircraft will attempt to maintain horizontally while flying home. If this is set to zero, WPNAV_SPEED will be used instead.
// @Units: cm/s
// @Range: 0 2000
// @Increment: 50
// @User: Standard
GSCALAR(rtl_speed_cms, "RTL_SPEED", 0),
// @Param: RTL_ALT_FINAL
// @DisplayName: RTL Final Altitude
// @Description: This is the altitude the vehicle will move to as the final stage of Returning to Launch or after completing a mission. Set to zero to land.
// @Units: cm
// @Range: -1 1000
// @Increment: 1
// @User: Standard
GSCALAR(rtl_alt_final, "RTL_ALT_FINAL", RTL_ALT_FINAL),
// @Param: RTL_CLIMB_MIN
// @DisplayName: RTL minimum climb
// @Description: The vehicle will climb this many cm during the initial climb portion of the RTL
// @Units: cm
// @Range: 0 3000
// @Increment: 10
// @User: Standard
GSCALAR(rtl_climb_min, "RTL_CLIMB_MIN", RTL_CLIMB_MIN_DEFAULT),
// @Param: RTL_LOIT_TIME
// @DisplayName: RTL loiter time
// @Description: Time (in milliseconds) to loiter above home before beginning final descent
// @Units: ms
// @Range: 0 60000
// @Increment: 1000
// @User: Standard
GSCALAR(rtl_loiter_time, "RTL_LOIT_TIME", RTL_LOITER_TIME),
#endif
#if RANGEFINDER_ENABLED == ENABLED
// @Param: RNGFND_GAIN
// @DisplayName: Rangefinder gain
// @Description: Used to adjust the speed with which the target altitude is changed when objects are sensed below the copter
// @Range: 0.01 2.0
// @Increment: 0.01
// @User: Standard
GSCALAR(rangefinder_gain, "RNGFND_GAIN", RANGEFINDER_GAIN_DEFAULT),
#endif
// @Param: FS_GCS_ENABLE
// @DisplayName: Ground Station Failsafe Enable
// @Description: Controls whether failsafe will be invoked (and what action to take) when connection with Ground station is lost for at least 5 seconds. NB. The GCS Failsafe is only active when RC_OVERRIDE is being used to control the vehicle.
// @Values: 0:Disabled,1:Enabled always RTL,2:Enabled Continue with Mission in Auto Mode,3:Enabled always SmartRTL or RTL,4:Enabled always SmartRTL or Land
// @User: Standard
GSCALAR(failsafe_gcs, "FS_GCS_ENABLE", FS_GCS_ENABLED_ALWAYS_RTL),
// @Param: GPS_HDOP_GOOD
// @DisplayName: GPS Hdop Good
// @Description: GPS Hdop value at or below this value represent a good position. Used for pre-arm checks
// @Range: 100 900
// @User: Advanced
GSCALAR(gps_hdop_good, "GPS_HDOP_GOOD", GPS_HDOP_GOOD_DEFAULT),
// @Param: MAG_ENABLE
// @DisplayName: Compass enable/disable
// @Description: Setting this to Enabled(1) will enable the compass. Setting this to Disabled(0) will disable the compass
// @Values: 0:Disabled,1:Enabled
// @User: Standard
GSCALAR(compass_enabled, "MAG_ENABLE", MAGNETOMETER),
// @Param: SUPER_SIMPLE
// @DisplayName: Super Simple Mode
// @Description: Bitmask to enable Super Simple mode for some flight modes. Setting this to Disabled(0) will disable Super Simple Mode
// @Values: 0:Disabled,1:Mode1,2:Mode2,3:Mode1+2,4:Mode3,5:Mode1+3,6:Mode2+3,7:Mode1+2+3,8:Mode4,9:Mode1+4,10:Mode2+4,11:Mode1+2+4,12:Mode3+4,13:Mode1+3+4,14:Mode2+3+4,15:Mode1+2+3+4,16:Mode5,17:Mode1+5,18:Mode2+5,19:Mode1+2+5,20:Mode3+5,21:Mode1+3+5,22:Mode2+3+5,23:Mode1+2+3+5,24:Mode4+5,25:Mode1+4+5,26:Mode2+4+5,27:Mode1+2+4+5,28:Mode3+4+5,29:Mode1+3+4+5,30:Mode2+3+4+5,31:Mode1+2+3+4+5,32:Mode6,33:Mode1+6,34:Mode2+6,35:Mode1+2+6,36:Mode3+6,37:Mode1+3+6,38:Mode2+3+6,39:Mode1+2+3+6,40:Mode4+6,41:Mode1+4+6,42:Mode2+4+6,43:Mode1+2+4+6,44:Mode3+4+6,45:Mode1+3+4+6,46:Mode2+3+4+6,47:Mode1+2+3+4+6,48:Mode5+6,49:Mode1+5+6,50:Mode2+5+6,51:Mode1+2+5+6,52:Mode3+5+6,53:Mode1+3+5+6,54:Mode2+3+5+6,55:Mode1+2+3+5+6,56:Mode4+5+6,57:Mode1+4+5+6,58:Mode2+4+5+6,59:Mode1+2+4+5+6,60:Mode3+4+5+6,61:Mode1+3+4+5+6,62:Mode2+3+4+5+6,63:Mode1+2+3+4+5+6
// @User: Standard
GSCALAR(super_simple, "SUPER_SIMPLE", 0),
// @Param: WP_YAW_BEHAVIOR
// @DisplayName: Yaw behaviour during missions
// @Description: Determines how the autopilot controls the yaw during missions and RTL
// @Values: 0:Never change yaw, 1:Face next waypoint, 2:Face next waypoint except RTL, 3:Face along GPS course
// @User: Standard
GSCALAR(wp_yaw_behavior, "WP_YAW_BEHAVIOR", WP_YAW_BEHAVIOR_DEFAULT),
// @Param: LAND_SPEED
// @DisplayName: Land speed
// @Description: The descent speed for the final stage of landing in cm/s
// @Units: cm/s
// @Range: 30 200
// @Increment: 10
// @User: Standard
GSCALAR(land_speed, "LAND_SPEED", LAND_SPEED),
// @Param: LAND_SPEED_HIGH
// @DisplayName: Land speed high
// @Description: The descent speed for the first stage of landing in cm/s. If this is zero then WPNAV_SPEED_DN is used
// @Units: cm/s
// @Range: 0 500
// @Increment: 10
// @User: Standard
GSCALAR(land_speed_high, "LAND_SPEED_HIGH", 0),
// @Param: PILOT_SPEED_UP
// @DisplayName: Pilot maximum vertical speed ascending
// @Description: The maximum vertical ascending velocity the pilot may request in cm/s
// @Units: cm/s
// @Range: 50 500
// @Increment: 10
// @User: Standard
GSCALAR(pilot_speed_up, "PILOT_SPEED_UP", PILOT_VELZ_MAX),
// @Param: PILOT_ACCEL_Z
// @DisplayName: Pilot vertical acceleration
// @Description: The vertical acceleration used when pilot is controlling the altitude
// @Units: cm/s/s
// @Range: 50 500
// @Increment: 10
// @User: Standard
GSCALAR(pilot_accel_z, "PILOT_ACCEL_Z", PILOT_ACCEL_Z_DEFAULT),
// @Param: FS_THR_ENABLE
// @DisplayName: Throttle Failsafe Enable
// @Description: The throttle failsafe allows you to configure a software failsafe activated by a setting on the throttle input channel
// @Values: 0:Disabled,1:Enabled always RTL,2:Enabled Continue with Mission in Auto Mode,3:Enabled always Land,4:Enabled always SmartRTL or RTL,5:Enabled always SmartRTL or Land
// @User: Standard
GSCALAR(failsafe_throttle, "FS_THR_ENABLE", FS_THR_ENABLED_ALWAYS_RTL),
// @Param: FS_THR_VALUE
// @DisplayName: Throttle Failsafe Value
// @Description: The PWM level in microseconds on channel 3 below which throttle failsafe triggers
// @Range: 925 1100
// @Units: PWM
// @Increment: 1
// @User: Standard
GSCALAR(failsafe_throttle_value, "FS_THR_VALUE", FS_THR_VALUE_DEFAULT),
// @Param: THR_DZ
// @DisplayName: Throttle deadzone
// @Description: The deadzone above and below mid throttle in PWM microseconds. Used in AltHold, Loiter, PosHold flight modes
// @User: Standard
// @Range: 0 300
// @Units: PWM
// @Increment: 1
GSCALAR(throttle_deadzone, "THR_DZ", THR_DZ_DEFAULT),
// @Param: FLTMODE1
// @DisplayName: Flight Mode 1
// @Description: Flight mode when Channel 5 pwm is <= 1230
// @Values: 0:Stabilize,1:Acro,2:AltHold,3:Auto,4:Guided,5:Loiter,6:RTL,7:Circle,9:Land,11:Drift,13:Sport,14:Flip,15:AutoTune,16:PosHold,17:Brake,18:Throw,19:Avoid_ADSB,20:Guided_NoGPS,21:Smart_RTL,22:FlowHold,23:Follow
// @User: Standard
GSCALAR(flight_mode1, "FLTMODE1", FLIGHT_MODE_1),
// @Param: FLTMODE2
// @DisplayName: Flight Mode 2
// @Description: Flight mode when Channel 5 pwm is >1230, <= 1360
// @Values: 0:Stabilize,1:Acro,2:AltHold,3:Auto,4:Guided,5:Loiter,6:RTL,7:Circle,9:Land,11:Drift,13:Sport,14:Flip,15:AutoTune,16:PosHold,17:Brake,18:Throw,19:Avoid_ADSB,20:Guided_NoGPS,21:Smart_RTL,22:FlowHold,23:Follow
// @User: Standard
GSCALAR(flight_mode2, "FLTMODE2", FLIGHT_MODE_2),
// @Param: FLTMODE3
// @DisplayName: Flight Mode 3
// @Description: Flight mode when Channel 5 pwm is >1360, <= 1490
// @Values: 0:Stabilize,1:Acro,2:AltHold,3:Auto,4:Guided,5:Loiter,6:RTL,7:Circle,9:Land,11:Drift,13:Sport,14:Flip,15:AutoTune,16:PosHold,17:Brake,18:Throw,19:Avoid_ADSB,20:Guided_NoGPS,21:Smart_RTL,22:FlowHold,23:Follow
// @User: Standard
GSCALAR(flight_mode3, "FLTMODE3", FLIGHT_MODE_3),
// @Param: FLTMODE4
// @DisplayName: Flight Mode 4
// @Description: Flight mode when Channel 5 pwm is >1490, <= 1620
// @Values: 0:Stabilize,1:Acro,2:AltHold,3:Auto,4:Guided,5:Loiter,6:RTL,7:Circle,9:Land,11:Drift,13:Sport,14:Flip,15:AutoTune,16:PosHold,17:Brake,18:Throw,19:Avoid_ADSB,20:Guided_NoGPS,21:Smart_RTL,22:FlowHold,23:Follow
// @User: Standard
GSCALAR(flight_mode4, "FLTMODE4", FLIGHT_MODE_4),
// @Param: FLTMODE5
// @DisplayName: Flight Mode 5
// @Description: Flight mode when Channel 5 pwm is >1620, <= 1749
// @Values: 0:Stabilize,1:Acro,2:AltHold,3:Auto,4:Guided,5:Loiter,6:RTL,7:Circle,9:Land,11:Drift,13:Sport,14:Flip,15:AutoTune,16:PosHold,17:Brake,18:Throw,19:Avoid_ADSB,20:Guided_NoGPS,21:Smart_RTL,22:FlowHold,23:Follow
// @User: Standard
GSCALAR(flight_mode5, "FLTMODE5", FLIGHT_MODE_5),
// @Param: FLTMODE6
// @DisplayName: Flight Mode 6
// @Description: Flight mode when Channel 5 pwm is >=1750
// @Values: 0:Stabilize,1:Acro,2:AltHold,3:Auto,4:Guided,5:Loiter,6:RTL,7:Circle,9:Land,11:Drift,13:Sport,14:Flip,15:AutoTune,16:PosHold,17:Brake,18:Throw,19:Avoid_ADSB,20:Guided_NoGPS,21:Smart_RTL,22:FlowHold,23:Follow
// @User: Standard
GSCALAR(flight_mode6, "FLTMODE6", FLIGHT_MODE_6),
// @Param: FLTMODE_CH
// @DisplayName: Flightmode channel
// @Description: RC Channel to use for flight mode control
// @Values: 0:Disabled,5:Channel5,6:Channel6,7:Channel7,8:Channel8
// @User: Advanced
GSCALAR(flight_mode_chan, "FLTMODE_CH", CH_MODE_DEFAULT),
// @Param: SIMPLE
// @DisplayName: Simple mode bitmask
// @Description: Bitmask which holds which flight modes use simple heading mode (eg bit 0 = 1 means Flight Mode 0 uses simple mode)
// @User: Advanced
GSCALAR(simple_modes, "SIMPLE", 0),
// @Param: LOG_BITMASK
// @DisplayName: Log bitmask
// @Description: 4 byte bitmap of log types to enable
// @Values: 830:Default,894:Default+RCIN,958:Default+IMU,1854:Default+Motors,-6146:NearlyAll-AC315,45054:NearlyAll,131071:All+FastATT,262142:All+MotBatt,393214:All+FastIMU,397310:All+FastIMU+PID,655358:All+FullIMU,0:Disabled
// @Bitmask: 0:ATTITUDE_FAST,1:ATTITUDE_MED,2:GPS,3:PM,4:CTUN,5:NTUN,6:RCIN,7:IMU,8:CMD,9:CURRENT,10:RCOUT,11:OPTFLOW,12:PID,13:COMPASS,14:INAV,15:CAMERA,17:MOTBATT,18:IMU_FAST,19:IMU_RAW
// @User: Standard
GSCALAR(log_bitmask, "LOG_BITMASK", DEFAULT_LOG_BITMASK),
// @Param: ESC_CALIBRATION
// @DisplayName: ESC Calibration
// @Description: Controls whether ArduCopter will enter ESC calibration on the next restart. Do not adjust this parameter manually.
// @User: Advanced
// @Values: 0:Normal Start-up, 1:Start-up in ESC Calibration mode if throttle high, 2:Start-up in ESC Calibration mode regardless of throttle, 3:Start-up and automatically calibrate ESCs, 9:Disabled
GSCALAR(esc_calibrate, "ESC_CALIBRATION", 0),
// @Param: TUNE
// @DisplayName: Channel 6 Tuning
// @Description: Controls which parameters (normally PID gains) are being tuned with transmitter's channel 6 knob
// @User: Standard
// @Values: 0:None,1:Stab Roll/Pitch kP,4:Rate Roll/Pitch kP,5:Rate Roll/Pitch kI,21:Rate Roll/Pitch kD,3:Stab Yaw kP,6:Rate Yaw kP,26:Rate Yaw kD,56:Rate Yaw Filter,55:Motor Yaw Headroom,14:AltHold kP,7:Throttle Rate kP,34:Throttle Accel kP,35:Throttle Accel kI,36:Throttle Accel kD,12:Loiter Pos kP,22:Velocity XY kP,28:Velocity XY kI,10:WP Speed,25:Acro RollPitch kP,40:Acro Yaw kP,45:RC Feel,13:Heli Ext Gyro,38:Declination,39:Circle Rate,41:RangeFinder Gain,46:Rate Pitch kP,47:Rate Pitch kI,48:Rate Pitch kD,49:Rate Roll kP,50:Rate Roll kI,51:Rate Roll kD,52:Rate Pitch FF,53:Rate Roll FF,54:Rate Yaw FF,57:Winch
GSCALAR(radio_tuning, "TUNE", 0),
// @Param: TUNE_LOW
// @DisplayName: Tuning minimum
// @Description: The minimum value that will be applied to the parameter currently being tuned with the transmitter's channel 6 knob
// @User: Standard
// @Range: 0 32767
GSCALAR(radio_tuning_low, "TUNE_LOW", 0),
// @Param: TUNE_HIGH
// @DisplayName: Tuning maximum
// @Description: The maximum value that will be applied to the parameter currently being tuned with the transmitter's channel 6 knob
// @User: Standard
// @Range: 0 32767
GSCALAR(radio_tuning_high, "TUNE_HIGH", 1000),
// @Param: FRAME_TYPE
// @DisplayName: Frame Type (+, X, V, etc)
// @Description: Controls motor mixing for multicopters. Not used for Tri or Traditional Helicopters.
// @Values: 0:Plus, 1:X, 2:V, 3:H, 4:V-Tail, 5:A-Tail, 10:Y6B
// @User: Standard
// @RebootRequired: True
GSCALAR(frame_type, "FRAME_TYPE", AP_Motors::MOTOR_FRAME_TYPE_X),
// @Group: ARMING_
// @Path: ../libraries/AP_Arming/AP_Arming.cpp
GOBJECT(arming, "ARMING_", AP_Arming_Copter),
// @Param: DISARM_DELAY
// @DisplayName: Disarm delay
// @Description: Delay before automatic disarm in seconds. A value of zero disables auto disarm.
// @Units: s
// @Range: 0 127
// @User: Advanced
GSCALAR(disarm_delay, "DISARM_DELAY", AUTO_DISARMING_DELAY),
// @Param: ANGLE_MAX
// @DisplayName: Angle Max
// @Description: Maximum lean angle in all flight modes
// @Units: cdeg
// @Range: 1000 8000
// @User: Advanced
ASCALAR(angle_max, "ANGLE_MAX", DEFAULT_ANGLE_MAX),
// @Param: PHLD_BRAKE_RATE
// @DisplayName: PosHold braking rate
// @Description: PosHold flight mode's rotation rate during braking in deg/sec
// @Units: deg/s
// @Range: 4 12
// @User: Advanced
GSCALAR(poshold_brake_rate, "PHLD_BRAKE_RATE", POSHOLD_BRAKE_RATE_DEFAULT),
// @Param: PHLD_BRAKE_ANGLE
// @DisplayName: PosHold braking angle max
// @Description: PosHold flight mode's max lean angle during braking in centi-degrees
// @Units: cdeg
// @Range: 2000 4500
// @User: Advanced
GSCALAR(poshold_brake_angle_max, "PHLD_BRAKE_ANGLE", POSHOLD_BRAKE_ANGLE_DEFAULT),
// @Param: LAND_REPOSITION
// @DisplayName: Land repositioning
// @Description: Enables user input during LAND mode, the landing phase of RTL, and auto mode landings.
// @Values: 0:No repositioning, 1:Repositioning
// @User: Advanced
GSCALAR(land_repositioning, "LAND_REPOSITION", LAND_REPOSITION_DEFAULT),
// @Param: FS_EKF_ACTION
// @DisplayName: EKF Failsafe Action
// @Description: Controls the action that will be taken when an EKF failsafe is invoked
// @Values: 1:Land, 2:AltHold, 3:Land even in Stabilize
// @User: Advanced
GSCALAR(fs_ekf_action, "FS_EKF_ACTION", FS_EKF_ACTION_DEFAULT),
// @Param: FS_EKF_THRESH
// @DisplayName: EKF failsafe variance threshold
// @Description: Allows setting the maximum acceptable compass and velocity variance
// @Values: 0.6:Strict, 0.8:Default, 1.0:Relaxed
// @User: Advanced
GSCALAR(fs_ekf_thresh, "FS_EKF_THRESH", FS_EKF_THRESHOLD_DEFAULT),
// @Param: FS_CRASH_CHECK
// @DisplayName: Crash check enable
// @Description: This enables automatic crash checking. When enabled the motors will disarm if a crash is detected.
// @Values: 0:Disabled, 1:Enabled
// @User: Advanced
GSCALAR(fs_crash_check, "FS_CRASH_CHECK", 1),
// @Param: RC_SPEED
// @DisplayName: ESC Update Speed
// @Description: This is the speed in Hertz that your ESCs will receive updates
// @Units: Hz
// @Range: 50 490
// @Increment: 1
// @User: Advanced
GSCALAR(rc_speed, "RC_SPEED", RC_FAST_SPEED),
// @Param: ACRO_RP_P
// @DisplayName: Acro Roll and Pitch P gain
// @Description: Converts pilot roll and pitch into a desired rate of rotation in ACRO and SPORT mode. Higher values mean faster rate of rotation.
// @Range: 1 10
// @User: Standard
GSCALAR(acro_rp_p, "ACRO_RP_P", ACRO_RP_P),
// @Param: ACRO_YAW_P
// @DisplayName: Acro Yaw P gain
// @Description: Converts pilot yaw input into a desired rate of rotation in ACRO, Stabilize and SPORT modes. Higher values mean faster rate of rotation.
// @Range: 1 10
// @User: Standard
GSCALAR(acro_yaw_p, "ACRO_YAW_P", ACRO_YAW_P),
#if MODE_ACRO_ENABLED == ENABLED || MODE_SPORT_ENABLED == ENABLED
// @Param: ACRO_BAL_ROLL
// @DisplayName: Acro Balance Roll
// @Description: rate at which roll angle returns to level in acro and sport mode. A higher value causes the vehicle to return to level faster.
// @Range: 0 3
// @Increment: 0.1
// @User: Advanced
GSCALAR(acro_balance_roll, "ACRO_BAL_ROLL", ACRO_BALANCE_ROLL),
// @Param: ACRO_BAL_PITCH
// @DisplayName: Acro Balance Pitch
// @Description: rate at which pitch angle returns to level in acro and sport mode. A higher value causes the vehicle to return to level faster.
// @Range: 0 3
// @Increment: 0.1
// @User: Advanced
GSCALAR(acro_balance_pitch, "ACRO_BAL_PITCH", ACRO_BALANCE_PITCH),
#endif
#if MODE_ACRO_ENABLED == ENABLED
// @Param: ACRO_TRAINER
// @DisplayName: Acro Trainer
// @Description: Type of trainer used in acro mode
// @Values: 0:Disabled,1:Leveling,2:Leveling and Limited
// @User: Advanced
GSCALAR(acro_trainer, "ACRO_TRAINER", ACRO_TRAINER_LIMITED),
// @Param: ACRO_RP_EXPO
// @DisplayName: Acro Roll/Pitch Expo
// @Description: Acro roll/pitch Expo to allow faster rotation when stick at edges
// @Values: 0:Disabled,0.1:Very Low,0.2:Low,0.3:Medium,0.4:High,0.5:Very High
// @Range: -0.5 1.0
// @User: Advanced
GSCALAR(acro_rp_expo, "ACRO_RP_EXPO", ACRO_RP_EXPO_DEFAULT),
#endif
// variables not in the g class which contain EEPROM saved variables
#if CAMERA == ENABLED
// @Group: CAM_
// @Path: ../libraries/AP_Camera/AP_Camera.cpp
GOBJECT(camera, "CAM_", AP_Camera),
#endif
// @Group: RELAY_
// @Path: ../libraries/AP_Relay/AP_Relay.cpp
GOBJECT(relay, "RELAY_", AP_Relay),
#if PARACHUTE == ENABLED
// @Group: CHUTE_
// @Path: ../libraries/AP_Parachute/AP_Parachute.cpp
GOBJECT(parachute, "CHUTE_", AP_Parachute),
#endif
// @Group: LGR_
// @Path: ../libraries/AP_LandingGear/AP_LandingGear.cpp
GOBJECT(landinggear, "LGR_", AP_LandingGear),
#if FRAME_CONFIG == HELI_FRAME
// @Group: IM_
// @Path: ../libraries/AC_InputManager/AC_InputManager_Heli.cpp
GOBJECT(input_manager, "IM_", AC_InputManager_Heli),
#endif
// @Group: COMPASS_
// @Path: ../libraries/AP_Compass/AP_Compass.cpp
GOBJECT(compass, "COMPASS_", Compass),
// @Group: INS_
// @Path: ../libraries/AP_InertialSensor/AP_InertialSensor.cpp
GOBJECT(ins, "INS_", AP_InertialSensor),
// @Group: WPNAV_
// @Path: ../libraries/AC_WPNav/AC_WPNav.cpp
GOBJECTPTR(wp_nav, "WPNAV_", AC_WPNav),
// @Group: LOIT_
// @Path: ../libraries/AC_WPNav/AC_Loiter.cpp
GOBJECTPTR(loiter_nav, "LOIT_", AC_Loiter),
#if MODE_CIRCLE_ENABLED == ENABLED
// @Group: CIRCLE_
// @Path: ../libraries/AC_WPNav/AC_Circle.cpp
GOBJECTPTR(circle_nav, "CIRCLE_", AC_Circle),
#endif
// @Group: ATC_
// @Path: ../libraries/AC_AttitudeControl/AC_AttitudeControl.cpp,../libraries/AC_AttitudeControl/AC_AttitudeControl_Multi.cpp,../libraries/AC_AttitudeControl/AC_AttitudeControl_Heli.cpp
#if FRAME_CONFIG == HELI_FRAME
GOBJECTPTR(attitude_control, "ATC_", AC_AttitudeControl_Heli),
#else
GOBJECTPTR(attitude_control, "ATC_", AC_AttitudeControl_Multi),
#endif
// @Group: PSC
// @Path: ../libraries/AC_AttitudeControl/AC_PosControl.cpp
GOBJECTPTR(pos_control, "PSC", AC_PosControl),
// @Group: SR0_
// @Path: GCS_Mavlink.cpp
GOBJECTN(_gcs._chan[0], gcs0, "SR0_", GCS_MAVLINK),
// @Group: SR1_
// @Path: GCS_Mavlink.cpp
GOBJECTN(_gcs._chan[1], gcs1, "SR1_", GCS_MAVLINK),
// @Group: SR2_
// @Path: GCS_Mavlink.cpp
GOBJECTN(_gcs._chan[2], gcs2, "SR2_", GCS_MAVLINK),
// @Group: SR3_
// @Path: GCS_Mavlink.cpp
GOBJECTN(_gcs._chan[3], gcs3, "SR3_", GCS_MAVLINK),
// @Group: AHRS_
// @Path: ../libraries/AP_AHRS/AP_AHRS.cpp
GOBJECT(ahrs, "AHRS_", AP_AHRS),
#if MOUNT == ENABLED
// @Group: MNT
// @Path: ../libraries/AP_Mount/AP_Mount.cpp
GOBJECT(camera_mount, "MNT", AP_Mount),
#endif
// @Group: LOG
// @Path: ../libraries/DataFlash/DataFlash.cpp
GOBJECT(DataFlash, "LOG", DataFlash_Class),
// @Group: BATT
// @Path: ../libraries/AP_BattMonitor/AP_BattMonitor.cpp
GOBJECT(battery, "BATT", AP_BattMonitor),
// @Group: BRD_
// @Path: ../libraries/AP_BoardConfig/AP_BoardConfig.cpp
GOBJECT(BoardConfig, "BRD_", AP_BoardConfig),
#if HAL_WITH_UAVCAN
// @Group: CAN_
// @Path: ../libraries/AP_BoardConfig/AP_BoardConfig_CAN.cpp
GOBJECT(BoardConfig_CAN, "CAN_", AP_BoardConfig_CAN),
#endif
#if SPRAYER_ENABLED == ENABLED
// @Group: SPRAY_
// @Path: ../libraries/AC_Sprayer/AC_Sprayer.cpp
GOBJECT(sprayer, "SPRAY_", AC_Sprayer),
#endif
#if CONFIG_HAL_BOARD == HAL_BOARD_SITL
GOBJECT(sitl, "SIM_", SITL::SITL),
#endif
// @Group: GND_
// @Path: ../libraries/AP_Baro/AP_Baro.cpp
GOBJECT(barometer, "GND_", AP_Baro),
// GPS driver
// @Group: GPS_
// @Path: ../libraries/AP_GPS/AP_GPS.cpp
GOBJECT(gps, "GPS_", AP_GPS),
// @Group: SCHED_
// @Path: ../libraries/AP_Scheduler/AP_Scheduler.cpp
GOBJECT(scheduler, "SCHED_", AP_Scheduler),
#if AC_FENCE == ENABLED
// @Group: FENCE_
// @Path: ../libraries/AC_Fence/AC_Fence.cpp
GOBJECT(fence, "FENCE_", AC_Fence),
#endif
// @Group: AVOID_
// @Path: ../libraries/AC_Avoidance/AC_Avoid.cpp
#if AC_AVOID_ENABLED == ENABLED
GOBJECT(avoid, "AVOID_", AC_Avoid),
#endif
#if AC_RALLY == ENABLED
// @Group: RALLY_
// @Path: AP_Rally.cpp,../libraries/AP_Rally/AP_Rally.cpp
GOBJECT(rally, "RALLY_", AP_Rally_Copter),
#endif
#if FRAME_CONFIG == HELI_FRAME
// @Group: H_
// @Path: ../libraries/AP_Motors/AP_MotorsHeli_Single.cpp,../libraries/AP_Motors/AP_MotorsHeli_Dual.cpp,../libraries/AP_Motors/AP_MotorsHeli.cpp
GOBJECTVARPTR(motors, "H_", &copter.motors_var_info),
#else
// @Group: MOT_
// @Path: ../libraries/AP_Motors/AP_MotorsMulticopter.cpp
GOBJECTVARPTR(motors, "MOT_", &copter.motors_var_info),
#endif
// @Group: RCMAP_
// @Path: ../libraries/AP_RCMapper/AP_RCMapper.cpp
GOBJECT(rcmap, "RCMAP_", RCMapper),
// @Group: EK2_
// @Path: ../libraries/AP_NavEKF2/AP_NavEKF2.cpp
GOBJECTN(EKF2, NavEKF2, "EK2_", NavEKF2),
// @Group: EK3_
// @Path: ../libraries/AP_NavEKF3/AP_NavEKF3.cpp
GOBJECTN(EKF3, NavEKF3, "EK3_", NavEKF3),
#if MODE_AUTO_ENABLED == ENABLED
// @Group: MIS_
// @Path: ../libraries/AP_Mission/AP_Mission.cpp
GOBJECT(mission, "MIS_", AP_Mission),
#endif
// @Group: RSSI_
// @Path: ../libraries/AP_RSSI/AP_RSSI.cpp
GOBJECT(rssi, "RSSI_", AP_RSSI),
#if RANGEFINDER_ENABLED == ENABLED
// @Group: RNGFND
// @Path: ../libraries/AP_RangeFinder/RangeFinder.cpp
GOBJECT(rangefinder, "RNGFND", RangeFinder),
#endif
#if AP_TERRAIN_AVAILABLE && AC_TERRAIN
// @Group: TERRAIN_
// @Path: ../libraries/AP_Terrain/AP_Terrain.cpp
GOBJECT(terrain, "TERRAIN_", AP_Terrain),
#endif
#if OPTFLOW == ENABLED
// @Group: FLOW
// @Path: ../libraries/AP_OpticalFlow/OpticalFlow.cpp
GOBJECT(optflow, "FLOW", OpticalFlow),
#endif
#if PRECISION_LANDING == ENABLED
// @Group: PLND_
// @Path: ../libraries/AC_PrecLand/AC_PrecLand.cpp
GOBJECT(precland, "PLND_", AC_PrecLand),
#endif
#if RPM_ENABLED == ENABLED
// @Group: RPM
// @Path: ../libraries/AP_RPM/AP_RPM.cpp
GOBJECT(rpm_sensor, "RPM", AP_RPM),
#endif
#if ADSB_ENABLED == ENABLED
// @Group: ADSB_
// @Path: ../libraries/AP_ADSB/AP_ADSB.cpp
GOBJECT(adsb, "ADSB_", AP_ADSB),
// @Group: AVD_
// @Path: ../libraries/AP_Avoidance/AP_Avoidance.cpp
GOBJECT(avoidance_adsb, "AVD_", AP_Avoidance_Copter),
#endif
#if AUTOTUNE_ENABLED == ENABLED
// @Param: AUTOTUNE_AXES
// @DisplayName: Autotune axis bitmask
// @Description: 1-byte bitmap of axes to autotune
// @Values: 7:All,1:Roll Only,2:Pitch Only,4:Yaw Only,3:Roll and Pitch,5:Roll and Yaw,6:Pitch and Yaw
// @Bitmask: 0:Roll,1:Pitch,2:Yaw
// @User: Standard
GSCALAR(autotune_axis_bitmask, "AUTOTUNE_AXES", 7), // AUTOTUNE_AXIS_BITMASK_DEFAULT
// @Param: AUTOTUNE_AGGR
// @DisplayName: Autotune aggressiveness
// @Description: Autotune aggressiveness. Defines the bounce back used to detect size of the D term.
// @Range: 0.05 0.10
// @User: Standard
GSCALAR(autotune_aggressiveness, "AUTOTUNE_AGGR", 0.1f),
// @Param: AUTOTUNE_MIN_D
// @DisplayName: AutoTune minimum D
// @Description: Defines the minimum D gain
// @Range: 0.001 0.006
// @User: Standard
GSCALAR(autotune_min_d, "AUTOTUNE_MIN_D", 0.001f),
#endif
// @Group: NTF_
// @Path: ../libraries/AP_Notify/AP_Notify.cpp
GOBJECT(notify, "NTF_", AP_Notify),
#if MODE_THROW_ENABLED == ENABLED
// @Param: THROW_MOT_START
// @DisplayName: Start motors before throwing is detected
// @Description: Used by THROW mode. Controls whether motors will run at the speed set by THR_MIN or will be stopped when armed and waiting for the throw.
// @Values: 0:Stopped,1:Running
// @User: Standard
GSCALAR(throw_motor_start, "THROW_MOT_START", 0),
#endif
#if AP_TERRAIN_AVAILABLE && AC_TERRAIN
// @Param: TERRAIN_FOLLOW
// @DisplayName: Terrain Following use control
// @Description: This enables terrain following for RTL and LAND flight modes. To use this option TERRAIN_ENABLE must be 1 and the GCS must support sending terrain data to the aircraft. In RTL the RTL_ALT will be considered a height above the terrain. In LAND mode the vehicle will slow to LAND_SPEED 10m above terrain (instead of 10m above home). This parameter does not affect AUTO and Guided which use a per-command flag to determine if the height is above-home, absolute or above-terrain.
// @Values: 0:Do Not Use in RTL and Land,1:Use in RTL and Land
// @User: Standard
GSCALAR(terrain_follow, "TERRAIN_FOLLOW", 0),
#endif
#if OSD_ENABLED == ENABLED
// @Group: OSD
// @Path: ../libraries/AP_OSD/AP_OSD.cpp
GOBJECT(osd, "OSD", AP_OSD),
#endif
// @Group:
// @Path: Parameters.cpp
GOBJECT(g2, "", ParametersG2),
AP_VAREND
};
/*
2nd group of parameters
*/
const AP_Param::GroupInfo ParametersG2::var_info[] = {
// @Param: WP_NAVALT_MIN
// @DisplayName: Minimum navigation altitude
// @Description: This is the altitude in meters above which for navigation can begin. This applies in auto takeoff and auto landing.
// @Range: 0 5
// @User: Standard
AP_GROUPINFO("WP_NAVALT_MIN", 1, ParametersG2, wp_navalt_min, 0),
// @Group: BTN_
// @Path: ../libraries/AP_Button/AP_Button.cpp
AP_SUBGROUPINFO(button, "BTN_", 2, ParametersG2, AP_Button),
#if MODE_THROW_ENABLED == ENABLED
// @Param: THROW_NEXTMODE
// @DisplayName: Throw mode's follow up mode
// @Description: Vehicle will switch to this mode after the throw is successfully completed. Default is to stay in throw mode (18)
// @Values: 3:Auto,4:Guided,5:LOITER,6:RTL,9:Land,17:Brake,18:Throw
// @User: Standard
AP_GROUPINFO("THROW_NEXTMODE", 3, ParametersG2, throw_nextmode, 18),
// @Param: THROW_TYPE
// @DisplayName: Type of Type
// @Description: Used by THROW mode. Specifies whether Copter is thrown upward or dropped.
// @Values: 0:Upward Throw,1:Drop
// @User: Standard
AP_GROUPINFO("THROW_TYPE", 4, ParametersG2, throw_type, Copter::ModeThrow::ThrowType_Upward),
#endif
// @Param: GND_EFFECT_COMP
// @DisplayName: Ground Effect Compensation Enable/Disable
// @Description: Ground Effect Compensation Enable/Disable
// @Values: 0:Disabled,1:Enabled
// @User: Advanced
AP_GROUPINFO("GND_EFFECT_COMP", 5, ParametersG2, gndeffect_comp_enabled, 0),
#if ADVANCED_FAILSAFE == ENABLED
// @Group: AFS_
// @Path: ../libraries/AP_AdvancedFailsafe/AP_AdvancedFailsafe.cpp
AP_SUBGROUPINFO(afs, "AFS_", 6, ParametersG2, AP_AdvancedFailsafe),
#endif
// @Param: DEV_OPTIONS
// @DisplayName: Development options
// @Description: Bitmask of developer options. The meanings of the bit fields in this parameter may vary at any time. Developers should check the source code for current meaning
// @Bitmask: 0:ADSBMavlinkProcessing
// @User: Advanced
AP_GROUPINFO("DEV_OPTIONS", 7, ParametersG2, dev_options, 0),
#if BEACON_ENABLED == ENABLED
// @Group: BCN
// @Path: ../libraries/AP_Beacon/AP_Beacon.cpp
AP_SUBGROUPINFO(beacon, "BCN", 14, ParametersG2, AP_Beacon),
#endif
#if PROXIMITY_ENABLED == ENABLED
// @Group: PRX
// @Path: ../libraries/AP_Proximity/AP_Proximity.cpp
AP_SUBGROUPINFO(proximity, "PRX", 8, ParametersG2, AP_Proximity),
#endif
// @Param: ACRO_Y_EXPO
// @DisplayName: Acro Yaw Expo
// @Description: Acro yaw expo to allow faster rotation when stick at edges
// @Values: 0:Disabled,0.1:Very Low,0.2:Low,0.3:Medium,0.4:High,0.5:Very High
// @Range: -0.5 1.0
// @User: Advanced
AP_GROUPINFO("ACRO_Y_EXPO", 9, ParametersG2, acro_y_expo, ACRO_Y_EXPO_DEFAULT),
#if MODE_ACRO_ENABLED == ENABLED
// @Param: ACRO_THR_MID
// @DisplayName: Acro Thr Mid
// @Description: Acro Throttle Mid
// @Range: 0 1
// @User: Advanced
AP_GROUPINFO("ACRO_THR_MID", 10, ParametersG2, acro_thr_mid, ACRO_THR_MID_DEFAULT),
#endif
// @Param: SYSID_ENFORCE
// @DisplayName: GCS sysid enforcement
// @Description: This controls whether packets from other than the expected GCS system ID will be accepted
// @Values: 0:NotEnforced,1:Enforced
// @User: Advanced
AP_GROUPINFO("SYSID_ENFORCE", 11, ParametersG2, sysid_enforce, 0),
#if STATS_ENABLED == ENABLED
// @Group: STAT
// @Path: ../libraries/AP_Stats/AP_Stats.cpp
AP_SUBGROUPINFO(stats, "STAT", 12, ParametersG2, AP_Stats),
#endif
#if GRIPPER_ENABLED == ENABLED
// @Group: GRIP_
// @Path: ../libraries/AP_Gripper/AP_Gripper.cpp
AP_SUBGROUPINFO(gripper, "GRIP_", 13, ParametersG2, AP_Gripper),
#endif
// @Param: FRAME_CLASS
// @DisplayName: Frame Class
// @Description: Controls major frame class for multicopter component
// @Values: 0:Undefined, 1:Quad, 2:Hexa, 3:Octa, 4:OctaQuad, 5:Y6, 6:Heli, 7:Tri, 8:SingleCopter, 9:CoaxCopter, 11:Heli_Dual, 12:DodecaHexa, 13:HeliQuad
// @User: Standard
// @RebootRequired: True
AP_GROUPINFO("FRAME_CLASS", 15, ParametersG2, frame_class, 0),
// @Group: SERVO
// @Path: ../libraries/SRV_Channel/SRV_Channels.cpp
AP_SUBGROUPINFO(servo_channels, "SERVO", 16, ParametersG2, SRV_Channels),
// @Group: RC
// @Path: ../libraries/RC_Channel/RC_Channels.cpp
AP_SUBGROUPINFO(rc_channels, "RC", 17, ParametersG2, RC_Channels_Copter),
#if VISUAL_ODOMETRY_ENABLED == ENABLED
// @Group: VISO
// @Path: ../libraries/AP_VisualOdom/AP_VisualOdom.cpp
AP_SUBGROUPINFO(visual_odom, "VISO", 18, ParametersG2, AP_VisualOdom),
#endif
// @Group: TCAL
// @Path: ../libraries/AP_TempCalibration/AP_TempCalibration.cpp
AP_SUBGROUPINFO(temp_calibration, "TCAL", 19, ParametersG2, AP_TempCalibration),
#if TOY_MODE_ENABLED == ENABLED
// @Group: TMODE
// @Path: toy_mode.cpp
AP_SUBGROUPINFO(toy_mode, "TMODE", 20, ParametersG2, ToyMode),
#endif
#if MODE_SMARTRTL_ENABLED == ENABLED
// @Group: SRTL_
// @Path: ../libraries/AP_SmartRTL/AP_SmartRTL.cpp
AP_SUBGROUPINFO(smart_rtl, "SRTL_", 21, ParametersG2, AP_SmartRTL),
#endif
#if WINCH_ENABLED == ENABLED
// @Group: WENC
// @Path: ../libraries/AP_WheelEncoder/AP_WheelEncoder.cpp
AP_SUBGROUPINFO(wheel_encoder, "WENC", 22, ParametersG2, AP_WheelEncoder),
// @Group: WINCH_
// @Path: ../libraries/AP_Winch/AP_Winch.cpp
AP_SUBGROUPINFO(winch, "WINCH", 23, ParametersG2, AP_Winch),
#endif
// @Param: PILOT_SPEED_DN
// @DisplayName: Pilot maximum vertical speed descending
// @Description: The maximum vertical descending velocity the pilot may request in cm/s
// @Units: cm/s
// @Range: 50 500
// @Increment: 10
// @User: Standard
AP_GROUPINFO("PILOT_SPEED_DN", 24, ParametersG2, pilot_speed_dn, 0),
// @Param: LAND_ALT_LOW
// @DisplayName: Land alt low
// @Description: Altitude during Landing at which vehicle slows to LAND_SPEED
// @Units: cm
// @Range: 100 10000
// @Increment: 10
// @User: Advanced
AP_GROUPINFO("LAND_ALT_LOW", 25, ParametersG2, land_alt_low, 1000),
#if !HAL_MINIMIZE_FEATURES && OPTFLOW == ENABLED
// @Group: FHLD
// @Path: mode_flowhold.cpp
AP_SUBGROUPPTR(mode_flowhold_ptr, "FHLD", 26, ParametersG2, Copter::ModeFlowHold),
#endif
#if MODE_FOLLOW_ENABLED == ENABLED
// @Group: FOLL
// @Path: ../libraries/AP_Follow/AP_Follow.cpp
AP_SUBGROUPINFO(follow, "FOLL", 27, ParametersG2, AP_Follow),
#endif
AP_GROUPEND
};
/*
constructor for g2 object
*/
ParametersG2::ParametersG2(void)
: temp_calibration() // this doesn't actually need constructing, but removing it here is problematic syntax-wise
#if BEACON_ENABLED == ENABLED
, beacon(copter.serial_manager)
#endif
#if PROXIMITY_ENABLED == ENABLED
, proximity(copter.serial_manager)
#endif
#if ADVANCED_FAILSAFE == ENABLED
,afs(copter.mission, copter.gps)
#endif
#if MODE_SMARTRTL_ENABLED == ENABLED
,smart_rtl()
#endif
#if !HAL_MINIMIZE_FEATURES && OPTFLOW == ENABLED
,mode_flowhold_ptr(&copter.mode_flowhold)
#endif
#if MODE_FOLLOW_ENABLED == ENABLED
,follow()
#endif
{
AP_Param::setup_object_defaults(this, var_info);
}
/*
This is a conversion table from old parameter values to new
parameter names. The startup code looks for saved values of the old
parameters and will copy them across to the new parameters if the
new parameter does not yet have a saved value. It then saves the new
value.
Note that this works even if the old parameter has been removed. It
relies on the old k_param index not being removed
The second column below is the index in the var_info[] table for the
old object. This should be zero for top level parameters.
*/
const AP_Param::ConversionInfo conversion_table[] = {
{ Parameters::k_param_battery_monitoring, 0, AP_PARAM_INT8, "BATT_MONITOR" },
{ Parameters::k_param_battery_volt_pin, 0, AP_PARAM_INT8, "BATT_VOLT_PIN" },
{ Parameters::k_param_battery_curr_pin, 0, AP_PARAM_INT8, "BATT_CURR_PIN" },
{ Parameters::k_param_volt_div_ratio, 0, AP_PARAM_FLOAT, "BATT_VOLT_MULT" },
{ Parameters::k_param_curr_amp_per_volt, 0, AP_PARAM_FLOAT, "BATT_AMP_PERVOLT" },
{ Parameters::k_param_pack_capacity, 0, AP_PARAM_INT32, "BATT_CAPACITY" },
{ Parameters::k_param_log_bitmask_old, 0, AP_PARAM_INT16, "LOG_BITMASK" },
{ Parameters::k_param_serial0_baud, 0, AP_PARAM_INT16, "SERIAL0_BAUD" },
{ Parameters::k_param_serial1_baud, 0, AP_PARAM_INT16, "SERIAL1_BAUD" },