axi_demux.sv

// Copyright (c) 2019 ETH Zurich and University of Bologna.
// Copyright and related rights are licensed under the Solderpad Hardware
// License, Version 0.51 (the "License"); you may not use this file except in
// compliance with the License.  You may obtain a copy of the License at
// http://solderpad.org/licenses/SHL-0.51. Unless required by applicable law
// or agreed to in writing, software, hardware and materials distributed under
// this License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR
// CONDITIONS OF ANY KIND, either express or implied. See the License for the
// specific language governing permissions and limitations under the License.
//
// Authors:
// - Wolfgang Roenninger <wroennin@iis.ee.ethz.ch>
// - Andreas Kurth <akurth@iis.ee.ethz.ch>

`include "common_cells/registers.svh"

// axi_demux: Demultiplex an AXI bus from one slave port to multiple master ports.
// See `doc/axi_demux.md` for the documentation, including the definition of parameters and ports.
module axi_demux #(
  parameter int unsigned AxiIdWidth     = 32'd0,
  parameter type         aw_chan_t      = logic,
  parameter type         w_chan_t       = logic,
  parameter type         b_chan_t       = logic,
  parameter type         ar_chan_t      = logic,
  parameter type         r_chan_t       = logic,
  parameter type         req_t          = logic,
  parameter type         resp_t         = logic,
  parameter int unsigned NoMstPorts     = 32'd0,
  parameter int unsigned MaxTrans       = 32'd8,
  parameter int unsigned AxiLookBits    = 32'd3,
  parameter bit          UniqueIds      = 1'b0,
  parameter bit          FallThrough    = 1'b0,
  parameter bit          SpillAw        = 1'b1,
  parameter bit          SpillW         = 1'b0,
  parameter bit          SpillB         = 1'b0,
  parameter bit          SpillAr        = 1'b1,
  parameter bit          SpillR         = 1'b0,
  // Dependent parameters, DO NOT OVERRIDE!
  parameter int unsigned SelectWidth    = (NoMstPorts > 32'd1) ? $clog2(NoMstPorts) : 32'd1,
  parameter type         select_t       = logic [SelectWidth-1:0]
) (
  input  logic                     clk_i,
  input  logic                     rst_ni,
  input  logic                     test_i,
  // Slave Port
  input  req_t                     slv_req_i,
  input  select_t                  slv_aw_select_i,
  input  select_t                  slv_ar_select_i,
  output resp_t                    slv_resp_o,
  // Master Ports
  output req_t    [NoMstPorts-1:0] mst_reqs_o,
  input  resp_t   [NoMstPorts-1:0] mst_resps_i
);

  localparam int unsigned IdCounterWidth = MaxTrans > 1 ? $clog2(MaxTrans) : 1;

  //--------------------------------------
  // Typedefs for the FIFOs / Queues
  //--------------------------------------
  typedef struct packed {
    aw_chan_t aw_chan;
    select_t  aw_select;
  } aw_chan_select_t;
  typedef struct packed {
    ar_chan_t ar_chan;
    select_t  ar_select;
  } ar_chan_select_t;

  // pass through if only one master port
  if (NoMstPorts == 32'h1) begin : gen_no_demux
    assign mst_reqs_o[0] = slv_req_i;
    assign slv_resp_o    = mst_resps_i;
  // other non degenerate cases
  end else begin : gen_demux

    //--------------------------------------
    //--------------------------------------
    // Signal Declarations
    //--------------------------------------
    //--------------------------------------

    //--------------------------------------
    // Write Transaction
    //--------------------------------------
    // comes from spill register at input
    aw_chan_select_t          slv_aw_chan_select;
    logic                     slv_aw_valid,       slv_aw_ready;

    // AW ID counter
    select_t                  lookup_aw_select;
    logic                     aw_select_occupied, aw_id_cnt_full;
    logic                     aw_push;
    // Upon an ATOP load, inject IDs from the AW into the AR channel
    logic                     atop_inject;

    // W FIFO: stores the decision to which master W beats should go
    logic                     w_fifo_pop;
    logic                     w_fifo_full,        w_fifo_empty;
    select_t                  w_select;

    // Register which locks the AW valid signal
    logic                     lock_aw_valid_d,    lock_aw_valid_q, load_aw_lock;
    logic                     aw_valid,           aw_ready;

    // W channel from spill reg
    w_chan_t                  slv_w_chan;
    logic                     slv_w_valid,        slv_w_ready;

    // B channles input into the arbitration
    b_chan_t [NoMstPorts-1:0] mst_b_chans;
    logic    [NoMstPorts-1:0] mst_b_valids,       mst_b_readies;

    // B channel to spill register
    b_chan_t                  slv_b_chan;
    logic                     slv_b_valid,        slv_b_ready;

    //--------------------------------------
    // Read Transaction
    //--------------------------------------
    // comes from spill register at input
    ar_chan_select_t          slv_ar_chan_select;
    logic                     slv_ar_valid,       slv_ar_ready;

    // AR ID counter
    select_t                  lookup_ar_select;
    logic                     ar_select_occupied, ar_id_cnt_full;
    logic                     ar_push;

    // Register which locks the AR valid signel
    logic                     lock_ar_valid_d,    lock_ar_valid_q, load_ar_lock;
    logic                     ar_valid,           ar_ready;

    // R channles input into the arbitration
    r_chan_t [NoMstPorts-1:0] mst_r_chans;
    logic    [NoMstPorts-1:0] mst_r_valids, mst_r_readies;

    // R channel to spill register
    r_chan_t                  slv_r_chan;
    logic                     slv_r_valid,        slv_r_ready;

    //--------------------------------------
    //--------------------------------------
    // Channel Control
    //--------------------------------------
    //--------------------------------------

    //--------------------------------------
    // AW Channel
    //--------------------------------------
    // spill register at the channel input
    `ifdef TARGET_VSIM
    // Workaround for bug in Questa 2020.2 and 2021.1: Flatten the struct into a logic vector before
    // instantiating `spill_register`.
    typedef logic [$bits(aw_chan_select_t)-1:0] aw_chan_select_flat_t;
    `else
    typedef aw_chan_select_t aw_chan_select_flat_t;
    `endif
    aw_chan_select_flat_t slv_aw_chan_select_in_flat,
                          slv_aw_chan_select_out_flat;
    assign slv_aw_chan_select_in_flat = {slv_req_i.aw, slv_aw_select_i};
    spill_register #(
      .T       ( aw_chan_select_flat_t        ),
      .Bypass  ( ~SpillAw                     ) // because module param indicates if we want a spill reg
    ) i_aw_spill_reg (
      .clk_i   ( clk_i                        ),
      .rst_ni  ( rst_ni                       ),
      .valid_i ( slv_req_i.aw_valid           ),
      .ready_o ( slv_resp_o.aw_ready          ),
      .data_i  ( slv_aw_chan_select_in_flat   ),
      .valid_o ( slv_aw_valid                 ),
      .ready_i ( slv_aw_ready                 ),
      .data_o  ( slv_aw_chan_select_out_flat  )
    );
    assign slv_aw_chan_select = slv_aw_chan_select_out_flat;

    // Control of the AW handshake
    always_comb begin
      // AXI Handshakes
      slv_aw_ready = 1'b0;
      aw_valid     = 1'b0;
      // `lock_aw_valid`, used to be protocol conform as it is not allowed to deassert
      // a valid if there was no corresponding ready. As this process has to be able to inject
      // an AXI ID into the counter of the AR channel on an ATOP, there could be a case where
      // this process waits on `aw_ready` but in the mean time on the AR channel the counter gets
      // full.
      lock_aw_valid_d = lock_aw_valid_q;
      load_aw_lock    = 1'b0;
      // AW ID counter and W FIFO
      aw_push      = 1'b0;
      // ATOP injection into ar counter
      atop_inject  = 1'b0;
      // we had an arbitration decision, the valid is locked, wait for the transaction
      if (lock_aw_valid_q) begin
        aw_valid = 1'b1;
        // transaction
        if (aw_ready) begin
          slv_aw_ready    = 1'b1;
          lock_aw_valid_d = 1'b0;
          load_aw_lock    = 1'b1;
          atop_inject     = slv_aw_chan_select.aw_chan.atop[5]; // inject the ATOP if necessary
        end
      end else begin
        // Process can start handling a transaction if its `i_aw_id_counter` and `w_fifo` have
        // space in them. Further check if we could inject something on the AR channel.
        if (!aw_id_cnt_full && !w_fifo_full && !ar_id_cnt_full) begin
          // there is a valid AW vector make the id lookup and go further, if it passes
          if (slv_aw_valid && (!aw_select_occupied ||
             (slv_aw_chan_select.aw_select == lookup_aw_select))) begin
            // connect the handshake
            aw_valid     = 1'b1;
            // push arbitration to the W FIFO regardless, do not wait for the AW transaction
            aw_push      = 1'b1;
            // on AW transaction
            if (aw_ready) begin
              slv_aw_ready = 1'b1;
              atop_inject  = slv_aw_chan_select.aw_chan.atop[5];
            // no AW transaction this cycle, lock the decision
            end else begin
              lock_aw_valid_d = 1'b1;
              load_aw_lock    = 1'b1;
            end
          end
        end
      end
    end

    // lock the valid signal, as the selection gets pushed into the W FIFO on first assertion,
    // prevent further pushing
    `FFLARN(lock_aw_valid_q, lock_aw_valid_d, load_aw_lock, '0, clk_i, rst_ni)

    if (UniqueIds) begin : gen_unique_ids_aw
      // If the `UniqueIds` parameter is set, each write transaction has an ID that is unique among
      // all in-flight write transactions, or all write transactions with a given ID target the same
      // master port as all write transactions with the same ID, or both.  This means that the
      // signals that are driven by the ID counters if this parameter is not set can instead be
      // derived from existing signals.  The ID counters can therefore be omitted.
      assign lookup_aw_select = slv_aw_chan_select.aw_select;
      assign aw_select_occupied = 1'b0;
      assign aw_id_cnt_full = 1'b0;
    end else begin : gen_aw_id_counter
      axi_demux_id_counters #(
        .AxiIdBits         ( AxiLookBits    ),
        .CounterWidth      ( IdCounterWidth ),
        .mst_port_select_t ( select_t       )
      ) i_aw_id_counter (
        .clk_i                        ( clk_i                                         ),
        .rst_ni                       ( rst_ni                                        ),
        .lookup_axi_id_i              ( slv_aw_chan_select.aw_chan.id[0+:AxiLookBits] ),
        .lookup_mst_select_o          ( lookup_aw_select                              ),
        .lookup_mst_select_occupied_o ( aw_select_occupied                            ),
        .full_o                       ( aw_id_cnt_full                                ),
        .inject_axi_id_i              ( '0                                            ),
        .inject_i                     ( 1'b0                                          ),
        .push_axi_id_i                ( slv_aw_chan_select.aw_chan.id[0+:AxiLookBits] ),
        .push_mst_select_i            ( slv_aw_chan_select.aw_select                  ),
        .push_i                       ( aw_push                                       ),
        .pop_axi_id_i                 ( slv_b_chan.id[0+:AxiLookBits]                 ),
        .pop_i                        ( slv_b_valid & slv_b_ready                     )
      );
      // pop from ID counter on outward transaction
    end

    // FIFO to save W selection
    fifo_v3 #(
      .FALL_THROUGH ( FallThrough ),
      .DEPTH        ( MaxTrans    ),
      .dtype        ( select_t    )
    ) i_w_fifo (
      .clk_i     ( clk_i                        ),
      .rst_ni    ( rst_ni                       ),
      .flush_i   ( 1'b0                         ),
      .testmode_i( test_i                       ),
      .full_o    ( w_fifo_full                  ),
      .empty_o   ( w_fifo_empty                 ),
      .usage_o   (                              ),
      .data_i    ( slv_aw_chan_select.aw_select ),
      .push_i    ( aw_push                      ), // controlled from proc_aw_chan
      .data_o    ( w_select                     ), // where the w beat should go
      .pop_i     ( w_fifo_pop                   )  // controlled from proc_w_chan
    );

    //--------------------------------------
    //  W Channel
    //--------------------------------------
    spill_register #(
      .T       ( w_chan_t ),
      .Bypass  ( ~SpillW  )
    ) i_w_spill_reg(
      .clk_i   ( clk_i              ),
      .rst_ni  ( rst_ni             ),
      .valid_i ( slv_req_i.w_valid  ),
      .ready_o ( slv_resp_o.w_ready ),
      .data_i  ( slv_req_i.w        ),
      .valid_o ( slv_w_valid        ),
      .ready_i ( slv_w_ready        ),
      .data_o  ( slv_w_chan         )
    );

    //--------------------------------------
    //  B Channel
    //--------------------------------------
    // optional spill register
    spill_register #(
      .T       ( b_chan_t ),
      .Bypass  ( ~SpillB  )
    ) i_b_spill_reg (
      .clk_i   ( clk_i              ),
      .rst_ni  ( rst_ni             ),
      .valid_i ( slv_b_valid        ),
      .ready_o ( slv_b_ready        ),
      .data_i  ( slv_b_chan         ),
      .valid_o ( slv_resp_o.b_valid ),
      .ready_i ( slv_req_i.b_ready  ),
      .data_o  ( slv_resp_o.b       )
    );

    // Arbitration of the different B responses
    rr_arb_tree #(
      .NumIn    ( NoMstPorts ),
      .DataType ( b_chan_t   ),
      .AxiVldRdy( 1'b1       ),
      .LockIn   ( 1'b1       )
    ) i_b_mux (
      .clk_i  ( clk_i         ),
      .rst_ni ( rst_ni        ),
      .flush_i( 1'b0          ),
      .rr_i   ( '0            ),
      .req_i  ( mst_b_valids  ),
      .gnt_o  ( mst_b_readies ),
      .data_i ( mst_b_chans   ),
      .gnt_i  ( slv_b_ready   ),
      .req_o  ( slv_b_valid   ),
      .data_o ( slv_b_chan    ),
      .idx_o  (               )
    );

    //--------------------------------------
    //  AR Channel
    //--------------------------------------
    `ifdef TARGET_VSIM
    // Workaround for bug in Questa 2020.2 and 2021.1: Flatten the struct into a logic vector before
    // instantiating `spill_register`.
    typedef logic [$bits(ar_chan_select_t)-1:0] ar_chan_select_flat_t;
    `else
    typedef ar_chan_select_t ar_chan_select_flat_t;
    `endif
    ar_chan_select_flat_t slv_ar_chan_select_in_flat,
                          slv_ar_chan_select_out_flat;
    assign slv_ar_chan_select_in_flat = {slv_req_i.ar, slv_ar_select_i};
    spill_register #(
      .T       ( ar_chan_select_flat_t        ),
      .Bypass  ( ~SpillAr                     )
    ) i_ar_spill_reg (
      .clk_i   ( clk_i                        ),
      .rst_ni  ( rst_ni                       ),
      .valid_i ( slv_req_i.ar_valid           ),
      .ready_o ( slv_resp_o.ar_ready          ),
      .data_i  ( slv_ar_chan_select_in_flat   ),
      .valid_o ( slv_ar_valid                 ),
      .ready_i ( slv_ar_ready                 ),
      .data_o  ( slv_ar_chan_select_out_flat  )
    );
    assign slv_ar_chan_select = slv_ar_chan_select_out_flat;

    // control of the AR handshake
    always_comb begin
      // AXI Handshakes
      slv_ar_ready    = 1'b0;
      ar_valid        = 1'b0;
      // `lock_ar_valid`: Used to be protocol conform as it is not allowed to deassert `ar_valid`
      // if there was no corresponding `ar_ready`. There is the possibility that an injection
      // of a R response from an `atop` from the AW channel can change the occupied flag of the
      // `i_ar_id_counter`, even if it was previously empty. This FF prevents the deassertion.
      lock_ar_valid_d = lock_ar_valid_q;
      load_ar_lock    = 1'b0;
      // AR id counter
      ar_push         = 1'b0;
      // The process had an arbitration decision in a previous cycle, the valid is locked,
      // wait for the AR transaction.
      if (lock_ar_valid_q) begin
        ar_valid = 1'b1;
        // transaction
        if (ar_ready) begin
          slv_ar_ready    = 1'b1;
          ar_push         = 1'b1;
          lock_ar_valid_d = 1'b0;
          load_ar_lock    = 1'b1;
        end
      end else begin
        // The process can start handling AR transaction if `i_ar_id_counter` has space.
        if (!ar_id_cnt_full) begin
          // There is a valid AR, so look the ID up.
          if (slv_ar_valid && (!ar_select_occupied ||
             (slv_ar_chan_select.ar_select == lookup_ar_select))) begin
            // connect the AR handshake
            ar_valid     = 1'b1;
            // on transaction
            if (ar_ready) begin
              slv_ar_ready = 1'b1;
              ar_push      = 1'b1;
            // no transaction this cycle, lock the valid decision!
            end else begin
              lock_ar_valid_d = 1'b1;
              load_ar_lock    = 1'b1;
            end
          end
        end
      end
    end

    // this ff is needed so that ar does not get de-asserted if an atop gets injected
    `FFLARN(lock_ar_valid_q, lock_ar_valid_d, load_ar_lock, '0, clk_i, rst_ni)

    if (UniqueIds) begin : gen_unique_ids_ar
      // If the `UniqueIds` parameter is set, each read transaction has an ID that is unique among
      // all in-flight read transactions, or all read transactions with a given ID target the same
      // master port as all read transactions with the same ID, or both.  This means that the
      // signals that are driven by the ID counters if this parameter is not set can instead be
      // derived from existing signals.  The ID counters can therefore be omitted.
      assign lookup_ar_select = slv_ar_chan_select.ar_select;
      assign ar_select_occupied = 1'b0;
      assign ar_id_cnt_full = 1'b0;
    end else begin : gen_ar_id_counter
      axi_demux_id_counters #(
        .AxiIdBits         ( AxiLookBits    ),
        .CounterWidth      ( IdCounterWidth ),
        .mst_port_select_t ( select_t       )
      ) i_ar_id_counter (
        .clk_i                        ( clk_i                                         ),
        .rst_ni                       ( rst_ni                                        ),
        .lookup_axi_id_i              ( slv_ar_chan_select.ar_chan.id[0+:AxiLookBits] ),
        .lookup_mst_select_o          ( lookup_ar_select                              ),
        .lookup_mst_select_occupied_o ( ar_select_occupied                            ),
        .full_o                       ( ar_id_cnt_full                                ),
        .inject_axi_id_i              ( slv_aw_chan_select.aw_chan.id[0+:AxiLookBits] ),
        .inject_i                     ( atop_inject                                   ),
        .push_axi_id_i                ( slv_ar_chan_select.ar_chan.id[0+:AxiLookBits] ),
        .push_mst_select_i            ( slv_ar_chan_select.ar_select                  ),
        .push_i                       ( ar_push                                       ),
        .pop_axi_id_i                 ( slv_r_chan.id[0+:AxiLookBits]                 ),
        .pop_i                        ( slv_r_valid & slv_r_ready & slv_r_chan.last   )
      );
    end

    //--------------------------------------
    //  R Channel
    //--------------------------------------
    // optional spill register
    spill_register #(
      .T       ( r_chan_t ),
      .Bypass  ( ~SpillR  )
    ) i_r_spill_reg (
      .clk_i   ( clk_i              ),
      .rst_ni  ( rst_ni             ),
      .valid_i ( slv_r_valid        ),
      .ready_o ( slv_r_ready        ),
      .data_i  ( slv_r_chan         ),
      .valid_o ( slv_resp_o.r_valid ),
      .ready_i ( slv_req_i.r_ready  ),
      .data_o  ( slv_resp_o.r       )
    );

    // Arbitration of the different r responses
    rr_arb_tree #(
      .NumIn    ( NoMstPorts ),
      .DataType ( r_chan_t   ),
      .AxiVldRdy( 1'b1       ),
      .LockIn   ( 1'b1       )
    ) i_r_mux (
      .clk_i  ( clk_i         ),
      .rst_ni ( rst_ni        ),
      .flush_i( 1'b0          ),
      .rr_i   ( '0            ),
      .req_i  ( mst_r_valids  ),
      .gnt_o  ( mst_r_readies ),
      .data_i ( mst_r_chans   ),
      .gnt_i  ( slv_r_ready   ),
      .req_o  ( slv_r_valid   ),
      .data_o ( slv_r_chan    ),
      .idx_o  (               )
    );

   assign ar_ready = ar_valid & mst_resps_i[slv_ar_chan_select.ar_select].ar_ready;
   assign aw_ready = aw_valid & mst_resps_i[slv_aw_chan_select.aw_select].aw_ready;

    // process that defines the individual demuxes and assignments for the arbitration
    // as mst_reqs_o has to be drivem from the same always comb block!
    always_comb begin
      // default assignments
      mst_reqs_o  = '0;
      slv_w_ready = 1'b0;
      w_fifo_pop  = 1'b0;

      for (int unsigned i = 0; i < NoMstPorts; i++) begin
        // AW channel
        mst_reqs_o[i].aw       = slv_aw_chan_select.aw_chan;
        mst_reqs_o[i].aw_valid = 1'b0;
        if (aw_valid && (slv_aw_chan_select.aw_select == i)) begin
          mst_reqs_o[i].aw_valid = 1'b1;
        end

        //  W channel
        mst_reqs_o[i].w       = slv_w_chan;
        mst_reqs_o[i].w_valid = 1'b0;
        if (!w_fifo_empty && (w_select == i)) begin
          mst_reqs_o[i].w_valid = slv_w_valid;
          slv_w_ready           = mst_resps_i[i].w_ready;
          w_fifo_pop            = slv_w_valid & mst_resps_i[i].w_ready & slv_w_chan.last;
        end

        //  B channel
        mst_reqs_o[i].b_ready = mst_b_readies[i];

        // AR channel
        mst_reqs_o[i].ar       = slv_ar_chan_select.ar_chan;
        mst_reqs_o[i].ar_valid = 1'b0;
        if (ar_valid && (slv_ar_chan_select.ar_select == i)) begin
          mst_reqs_o[i].ar_valid = 1'b1;
        end

        //  R channel
        mst_reqs_o[i].r_ready = mst_r_readies[i];
      end
    end
    // unpack the response B and R channels for the arbitration
    for (genvar i = 0; i < NoMstPorts; i++) begin : gen_b_channels
      assign mst_b_chans[i]        = mst_resps_i[i].b;
      assign mst_b_valids[i]       = mst_resps_i[i].b_valid;
      assign mst_r_chans[i]        = mst_resps_i[i].r;
      assign mst_r_valids[i]       = mst_resps_i[i].r_valid;
    end


// Validate parameters.
// pragma translate_off
`ifndef VERILATOR
`ifndef XSIM
    initial begin: validate_params
      no_mst_ports: assume (NoMstPorts > 0) else
        $fatal(1, "The Number of slaves (NoMstPorts) has to be at least 1");
      AXI_ID_BITS:  assume (AxiIdWidth >= AxiLookBits) else
        $fatal(1, "AxiIdBits has to be equal or smaller than AxiIdWidth.");
    end
    default disable iff (!rst_ni);
    aw_select: assume property( @(posedge clk_i) (slv_req_i.aw_valid |->
                                                 (slv_aw_select_i < NoMstPorts))) else
      $fatal(1, "slv_aw_select_i is %d: AW has selected a slave that is not defined.\
                 NoMstPorts: %d", slv_aw_select_i, NoMstPorts);
    ar_select: assume property( @(posedge clk_i) (slv_req_i.ar_valid |->
                                                 (slv_ar_select_i < NoMstPorts))) else
      $fatal(1, "slv_ar_select_i is %d: AR has selected a slave that is not defined.\
                 NoMstPorts: %d", slv_ar_select_i, NoMstPorts);
    aw_valid_stable: assert property( @(posedge clk_i) (aw_valid && !aw_ready) |=> aw_valid) else
      $fatal(1, "aw_valid was deasserted, when aw_ready = 0 in last cycle.");
    ar_valid_stable: assert property( @(posedge clk_i)
                               (ar_valid && !ar_ready) |=> ar_valid) else
      $fatal(1, "ar_valid was deasserted, when ar_ready = 0 in last cycle.");
    aw_stable: assert property( @(posedge clk_i) (aw_valid && !aw_ready)
                               |=> $stable(slv_aw_chan_select)) else
      $fatal(1, "slv_aw_chan_select unstable with valid set.");
    ar_stable: assert property( @(posedge clk_i) (ar_valid && !ar_ready)
                               |=> $stable(slv_ar_chan_select)) else
      $fatal(1, "slv_aw_chan_select unstable with valid set.");
    internal_ar_select: assert property( @(posedge clk_i)
        (ar_valid |-> slv_ar_chan_select.ar_select < NoMstPorts))
      else $fatal(1, "slv_ar_chan_select.ar_select illegal while ar_valid.");
    internal_aw_select: assert property( @(posedge clk_i)
        (aw_valid |-> slv_aw_chan_select.aw_select < NoMstPorts))
      else $fatal(1, "slv_aw_chan_select.aw_select illegal while aw_valid.");
`endif
`endif
// pragma translate_on
  end
endmodule

module axi_demux_id_counters #(
  // the lower bits of the AXI ID that should be considered, results in 2**AXI_ID_BITS counters
  parameter int unsigned AxiIdBits         = 2,
  parameter int unsigned CounterWidth      = 4,
  parameter type         mst_port_select_t = logic
) (
  input                        clk_i,   // Clock
  input                        rst_ni,  // Asynchronous reset active low
  // lookup
  input  logic [AxiIdBits-1:0] lookup_axi_id_i,
  output mst_port_select_t     lookup_mst_select_o,
  output logic                 lookup_mst_select_occupied_o,
  // push
  output logic                 full_o,
  input  logic [AxiIdBits-1:0] push_axi_id_i,
  input  mst_port_select_t     push_mst_select_i,
  input  logic                 push_i,
  // inject ATOPs in AR channel
  input  logic [AxiIdBits-1:0] inject_axi_id_i,
  input  logic                 inject_i,
  // pop
  input  logic [AxiIdBits-1:0] pop_axi_id_i,
  input  logic                 pop_i
);
  localparam int unsigned NoCounters = 2**AxiIdBits;
  typedef logic [CounterWidth-1:0] cnt_t;

  // registers, each gets loaded when push_en[i]
  mst_port_select_t [NoCounters-1:0] mst_select_q;

  // counter signals
  logic [NoCounters-1:0] push_en, inject_en, pop_en, occupied, cnt_full;

  //-----------------------------------
  // Lookup
  //-----------------------------------
  assign lookup_mst_select_o          = mst_select_q[lookup_axi_id_i];
  assign lookup_mst_select_occupied_o = occupied[lookup_axi_id_i];
  //-----------------------------------
  // Push and Pop
  //-----------------------------------
  assign push_en   = (push_i)   ? (1 << push_axi_id_i)   : '0;
  assign inject_en = (inject_i) ? (1 << inject_axi_id_i) : '0;
  assign pop_en    = (pop_i)    ? (1 << pop_axi_id_i)    : '0;
  assign full_o    = |cnt_full;
  // counters
  for (genvar i = 0; i < NoCounters; i++) begin : gen_counters
    logic cnt_en, cnt_down, overflow;
    cnt_t cnt_delta, in_flight;
    always_comb begin
      unique case ({push_en[i], inject_en[i], pop_en[i]})
        3'b001  : begin // pop_i = -1
          cnt_en    = 1'b1;
          cnt_down  = 1'b1;
          cnt_delta = cnt_t'(1);
        end
        3'b010  : begin // inject_i = +1
          cnt_en    = 1'b1;
          cnt_down  = 1'b0;
          cnt_delta = cnt_t'(1);
        end
     // 3'b011, inject_i & pop_i = 0 --> use default
        3'b100  : begin // push_i = +1
          cnt_en    = 1'b1;
          cnt_down  = 1'b0;
          cnt_delta = cnt_t'(1);
        end
     // 3'b101, push_i & pop_i = 0 --> use default
        3'b110  : begin // push_i & inject_i = +2
          cnt_en    = 1'b1;
          cnt_down  = 1'b0;
          cnt_delta = cnt_t'(2);
        end
        3'b111  : begin // push_i & inject_i & pop_i = +1
          cnt_en    = 1'b1;
          cnt_down  = 1'b0;
          cnt_delta = cnt_t'(1);
        end
        default : begin // do nothing to the counters
          cnt_en    = 1'b0;
          cnt_down  = 1'b0;
          cnt_delta = cnt_t'(0);
        end
      endcase
    end

    delta_counter #(
      .WIDTH           ( CounterWidth ),
      .STICKY_OVERFLOW ( 1'b0         )
    ) i_in_flight_cnt (
      .clk_i      ( clk_i     ),
      .rst_ni     ( rst_ni    ),
      .clear_i    ( 1'b0      ),
      .en_i       ( cnt_en    ),
      .load_i     ( 1'b0      ),
      .down_i     ( cnt_down  ),
      .delta_i    ( cnt_delta ),
      .d_i        ( '0        ),
      .q_o        ( in_flight ),
      .overflow_o ( overflow  )
    );
    assign occupied[i] = |in_flight;
    assign cnt_full[i] = overflow | (&in_flight);

    // holds the selection signal for this id
    `FFLARN(mst_select_q[i], push_mst_select_i, push_en[i], '0, clk_i, rst_ni)

// pragma translate_off
`ifndef VERILATOR
`ifndef XSIM
    // Validate parameters.
    cnt_underflow: assert property(
      @(posedge clk_i) disable iff (~rst_ni) (pop_en[i] |=> !overflow)) else
        $fatal(1, "axi_demux_id_counters > Counter: %0d underflowed.\
                   The reason is probably a faulty AXI response.", i);
`endif
`endif
// pragma translate_on
  end
endmodule

// interface wrapper
`include "axi/assign.svh"
`include "axi/typedef.svh"
module axi_demux_intf #(
  parameter int unsigned AXI_ID_WIDTH     = 32'd0, // Synopsys DC requires default value for params
  parameter int unsigned AXI_ADDR_WIDTH   = 32'd0,
  parameter int unsigned AXI_DATA_WIDTH   = 32'd0,
  parameter int unsigned AXI_USER_WIDTH   = 32'd0,
  parameter int unsigned NO_MST_PORTS     = 32'd3,
  parameter int unsigned MAX_TRANS        = 32'd8,
  parameter int unsigned AXI_LOOK_BITS    = 32'd3,
  parameter bit          UNIQUE_IDS       = 1'b0,
  parameter bit          FALL_THROUGH     = 1'b0,
  parameter bit          SPILL_AW         = 1'b1,
  parameter bit          SPILL_W          = 1'b0,
  parameter bit          SPILL_B          = 1'b0,
  parameter bit          SPILL_AR         = 1'b1,
  parameter bit          SPILL_R          = 1'b0,
  // Dependent parameters, DO NOT OVERRIDE!
  parameter int unsigned SELECT_WIDTH   = (NO_MST_PORTS > 32'd1) ? $clog2(NO_MST_PORTS) : 32'd1,
  parameter type         select_t       = logic [SELECT_WIDTH-1:0] // MST port select type
) (
  input  logic    clk_i,                 // Clock
  input  logic    rst_ni,                // Asynchronous reset active low
  input  logic    test_i,                // Testmode enable
  input  select_t slv_aw_select_i,       // has to be stable, when aw_valid
  input  select_t slv_ar_select_i,       // has to be stable, when ar_valid
  AXI_BUS.Slave   slv,                   // slave port
  AXI_BUS.Master  mst [NO_MST_PORTS-1:0] // master ports
);

  typedef logic [AXI_ID_WIDTH-1:0]       id_t;
  typedef logic [AXI_ADDR_WIDTH-1:0]   addr_t;
  typedef logic [AXI_DATA_WIDTH-1:0]   data_t;
  typedef logic [AXI_DATA_WIDTH/8-1:0] strb_t;
  typedef logic [AXI_USER_WIDTH-1:0]   user_t;
  `AXI_TYPEDEF_AW_CHAN_T(aw_chan_t, addr_t, id_t, user_t)
  `AXI_TYPEDEF_W_CHAN_T(w_chan_t, data_t, strb_t, user_t)
  `AXI_TYPEDEF_B_CHAN_T(b_chan_t, id_t, user_t)
  `AXI_TYPEDEF_AR_CHAN_T(ar_chan_t, addr_t, id_t, user_t)
  `AXI_TYPEDEF_R_CHAN_T(r_chan_t, data_t, id_t, user_t)
  `AXI_TYPEDEF_REQ_T(req_t, aw_chan_t, w_chan_t, ar_chan_t)
  `AXI_TYPEDEF_RESP_T(resp_t, b_chan_t, r_chan_t)

  req_t                     slv_req;
  resp_t                    slv_resp;
  req_t  [NO_MST_PORTS-1:0] mst_req;
  resp_t [NO_MST_PORTS-1:0] mst_resp;

  `AXI_ASSIGN_TO_REQ(slv_req, slv)
  `AXI_ASSIGN_FROM_RESP(slv, slv_resp)

  for (genvar i = 0; i < NO_MST_PORTS; i++) begin : gen_assign_mst_ports
    `AXI_ASSIGN_FROM_REQ(mst[i], mst_req[i])
    `AXI_ASSIGN_TO_RESP(mst_resp[i], mst[i])
  end

  axi_demux #(
    .AxiIdWidth     ( AXI_ID_WIDTH  ), // ID Width
    .aw_chan_t      ( aw_chan_t     ), // AW Channel Type
    .w_chan_t       (  w_chan_t     ), //  W Channel Type
    .b_chan_t       (  b_chan_t     ), //  B Channel Type
    .ar_chan_t      ( ar_chan_t     ), // AR Channel Type
    .r_chan_t       (  r_chan_t     ), //  R Channel Type
    .req_t          (     req_t     ),
    .resp_t         (    resp_t     ),
    .NoMstPorts     ( NO_MST_PORTS  ),
    .MaxTrans       ( MAX_TRANS     ),
    .AxiLookBits    ( AXI_LOOK_BITS ),
    .UniqueIds      ( UNIQUE_IDS    ),
    .FallThrough    ( FALL_THROUGH  ),
    .SpillAw        ( SPILL_AW      ),
    .SpillW         ( SPILL_W       ),
    .SpillB         ( SPILL_B       ),
    .SpillAr        ( SPILL_AR      ),
    .SpillR         ( SPILL_R       )
  ) i_axi_demux (
    .clk_i,   // Clock
    .rst_ni,  // Asynchronous reset active low
    .test_i,  // Testmode enable
    // slave port
    .slv_req_i       ( slv_req         ),
    .slv_aw_select_i ( slv_aw_select_i ),
    .slv_ar_select_i ( slv_ar_select_i ),
    .slv_resp_o      ( slv_resp        ),
    // master port
    .mst_reqs_o      ( mst_req         ),
    .mst_resps_i     ( mst_resp        )
  );
endmodule