forked from torvalds/linux
-
Notifications
You must be signed in to change notification settings - Fork 0
/
adm1026.c
1780 lines (1594 loc) · 58.3 KB
/
adm1026.c
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
/*
adm1026.c - Part of lm_sensors, Linux kernel modules for hardware
monitoring
Copyright (C) 2002, 2003 Philip Pokorny <[email protected]>
Copyright (C) 2004 Justin Thiessen <[email protected]>
Chip details at:
<http://www.analog.com/UploadedFiles/Data_Sheets/779263102ADM1026_a.pdf>
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/jiffies.h>
#include <linux/i2c.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/hwmon-vid.h>
#include <linux/err.h>
#include <linux/mutex.h>
/* Addresses to scan */
static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
static int gpio_input[17] = { -1, -1, -1, -1, -1, -1, -1, -1, -1,
-1, -1, -1, -1, -1, -1, -1, -1 };
static int gpio_output[17] = { -1, -1, -1, -1, -1, -1, -1, -1, -1,
-1, -1, -1, -1, -1, -1, -1, -1 };
static int gpio_inverted[17] = { -1, -1, -1, -1, -1, -1, -1, -1, -1,
-1, -1, -1, -1, -1, -1, -1, -1 };
static int gpio_normal[17] = { -1, -1, -1, -1, -1, -1, -1, -1, -1,
-1, -1, -1, -1, -1, -1, -1, -1 };
static int gpio_fan[8] = { -1, -1, -1, -1, -1, -1, -1, -1 };
module_param_array(gpio_input, int, NULL, 0);
MODULE_PARM_DESC(gpio_input, "List of GPIO pins (0-16) to program as inputs");
module_param_array(gpio_output, int, NULL, 0);
MODULE_PARM_DESC(gpio_output, "List of GPIO pins (0-16) to program as "
"outputs");
module_param_array(gpio_inverted, int, NULL, 0);
MODULE_PARM_DESC(gpio_inverted, "List of GPIO pins (0-16) to program as "
"inverted");
module_param_array(gpio_normal, int, NULL, 0);
MODULE_PARM_DESC(gpio_normal, "List of GPIO pins (0-16) to program as "
"normal/non-inverted");
module_param_array(gpio_fan, int, NULL, 0);
MODULE_PARM_DESC(gpio_fan, "List of GPIO pins (0-7) to program as fan tachs");
/* Many ADM1026 constants specified below */
/* The ADM1026 registers */
#define ADM1026_REG_CONFIG1 0x00
#define CFG1_MONITOR 0x01
#define CFG1_INT_ENABLE 0x02
#define CFG1_INT_CLEAR 0x04
#define CFG1_AIN8_9 0x08
#define CFG1_THERM_HOT 0x10
#define CFG1_DAC_AFC 0x20
#define CFG1_PWM_AFC 0x40
#define CFG1_RESET 0x80
#define ADM1026_REG_CONFIG2 0x01
/* CONFIG2 controls FAN0/GPIO0 through FAN7/GPIO7 */
#define ADM1026_REG_CONFIG3 0x07
#define CFG3_GPIO16_ENABLE 0x01
#define CFG3_CI_CLEAR 0x02
#define CFG3_VREF_250 0x04
#define CFG3_GPIO16_DIR 0x40
#define CFG3_GPIO16_POL 0x80
#define ADM1026_REG_E2CONFIG 0x13
#define E2CFG_READ 0x01
#define E2CFG_WRITE 0x02
#define E2CFG_ERASE 0x04
#define E2CFG_ROM 0x08
#define E2CFG_CLK_EXT 0x80
/* There are 10 general analog inputs and 7 dedicated inputs
* They are:
* 0 - 9 = AIN0 - AIN9
* 10 = Vbat
* 11 = 3.3V Standby
* 12 = 3.3V Main
* 13 = +5V
* 14 = Vccp (CPU core voltage)
* 15 = +12V
* 16 = -12V
*/
static u16 ADM1026_REG_IN[] = {
0x30, 0x31, 0x32, 0x33, 0x34, 0x35,
0x36, 0x37, 0x27, 0x29, 0x26, 0x2a,
0x2b, 0x2c, 0x2d, 0x2e, 0x2f
};
static u16 ADM1026_REG_IN_MIN[] = {
0x58, 0x59, 0x5a, 0x5b, 0x5c, 0x5d,
0x5e, 0x5f, 0x6d, 0x49, 0x6b, 0x4a,
0x4b, 0x4c, 0x4d, 0x4e, 0x4f
};
static u16 ADM1026_REG_IN_MAX[] = {
0x50, 0x51, 0x52, 0x53, 0x54, 0x55,
0x56, 0x57, 0x6c, 0x41, 0x6a, 0x42,
0x43, 0x44, 0x45, 0x46, 0x47
};
/* Temperatures are:
* 0 - Internal
* 1 - External 1
* 2 - External 2
*/
static u16 ADM1026_REG_TEMP[] = { 0x1f, 0x28, 0x29 };
static u16 ADM1026_REG_TEMP_MIN[] = { 0x69, 0x48, 0x49 };
static u16 ADM1026_REG_TEMP_MAX[] = { 0x68, 0x40, 0x41 };
static u16 ADM1026_REG_TEMP_TMIN[] = { 0x10, 0x11, 0x12 };
static u16 ADM1026_REG_TEMP_THERM[] = { 0x0d, 0x0e, 0x0f };
static u16 ADM1026_REG_TEMP_OFFSET[] = { 0x1e, 0x6e, 0x6f };
#define ADM1026_REG_FAN(nr) (0x38 + (nr))
#define ADM1026_REG_FAN_MIN(nr) (0x60 + (nr))
#define ADM1026_REG_FAN_DIV_0_3 0x02
#define ADM1026_REG_FAN_DIV_4_7 0x03
#define ADM1026_REG_DAC 0x04
#define ADM1026_REG_PWM 0x05
#define ADM1026_REG_GPIO_CFG_0_3 0x08
#define ADM1026_REG_GPIO_CFG_4_7 0x09
#define ADM1026_REG_GPIO_CFG_8_11 0x0a
#define ADM1026_REG_GPIO_CFG_12_15 0x0b
/* CFG_16 in REG_CFG3 */
#define ADM1026_REG_GPIO_STATUS_0_7 0x24
#define ADM1026_REG_GPIO_STATUS_8_15 0x25
/* STATUS_16 in REG_STATUS4 */
#define ADM1026_REG_GPIO_MASK_0_7 0x1c
#define ADM1026_REG_GPIO_MASK_8_15 0x1d
/* MASK_16 in REG_MASK4 */
#define ADM1026_REG_COMPANY 0x16
#define ADM1026_REG_VERSTEP 0x17
/* These are the recognized values for the above regs */
#define ADM1026_COMPANY_ANALOG_DEV 0x41
#define ADM1026_VERSTEP_GENERIC 0x40
#define ADM1026_VERSTEP_ADM1026 0x44
#define ADM1026_REG_MASK1 0x18
#define ADM1026_REG_MASK2 0x19
#define ADM1026_REG_MASK3 0x1a
#define ADM1026_REG_MASK4 0x1b
#define ADM1026_REG_STATUS1 0x20
#define ADM1026_REG_STATUS2 0x21
#define ADM1026_REG_STATUS3 0x22
#define ADM1026_REG_STATUS4 0x23
#define ADM1026_FAN_ACTIVATION_TEMP_HYST -6
#define ADM1026_FAN_CONTROL_TEMP_RANGE 20
#define ADM1026_PWM_MAX 255
/* Conversions. Rounding and limit checking is only done on the TO_REG
* variants. Note that you should be a bit careful with which arguments
* these macros are called: arguments may be evaluated more than once.
*/
/* IN are scaled acording to built-in resistors. These are the
* voltages corresponding to 3/4 of full scale (192 or 0xc0)
* NOTE: The -12V input needs an additional factor to account
* for the Vref pullup resistor.
* NEG12_OFFSET = SCALE * Vref / V-192 - Vref
* = 13875 * 2.50 / 1.875 - 2500
* = 16000
*
* The values in this table are based on Table II, page 15 of the
* datasheet.
*/
static int adm1026_scaling[] = { /* .001 Volts */
2250, 2250, 2250, 2250, 2250, 2250,
1875, 1875, 1875, 1875, 3000, 3330,
3330, 4995, 2250, 12000, 13875
};
#define NEG12_OFFSET 16000
#define SCALE(val, from, to) (((val)*(to) + ((from)/2))/(from))
#define INS_TO_REG(n, val) (SENSORS_LIMIT(SCALE(val, adm1026_scaling[n], 192),\
0, 255))
#define INS_FROM_REG(n, val) (SCALE(val, 192, adm1026_scaling[n]))
/* FAN speed is measured using 22.5kHz clock and counts for 2 pulses
* and we assume a 2 pulse-per-rev fan tach signal
* 22500 kHz * 60 (sec/min) * 2 (pulse) / 2 (pulse/rev) == 1350000
*/
#define FAN_TO_REG(val, div) ((val) <= 0 ? 0xff : \
SENSORS_LIMIT(1350000/((val)*(div)), 1, 254))
#define FAN_FROM_REG(val, div) ((val) == 0 ? -1:(val) == 0xff ? 0 : \
1350000/((val)*(div)))
#define DIV_FROM_REG(val) (1<<(val))
#define DIV_TO_REG(val) ((val) >= 8 ? 3 : (val) >= 4 ? 2 : (val) >= 2 ? 1 : 0)
/* Temperature is reported in 1 degC increments */
#define TEMP_TO_REG(val) (SENSORS_LIMIT(((val)+((val)<0 ? -500 : 500))/1000,\
-127, 127))
#define TEMP_FROM_REG(val) ((val) * 1000)
#define OFFSET_TO_REG(val) (SENSORS_LIMIT(((val)+((val)<0 ? -500 : 500))/1000,\
-127, 127))
#define OFFSET_FROM_REG(val) ((val) * 1000)
#define PWM_TO_REG(val) (SENSORS_LIMIT(val, 0, 255))
#define PWM_FROM_REG(val) (val)
#define PWM_MIN_TO_REG(val) ((val) & 0xf0)
#define PWM_MIN_FROM_REG(val) (((val) & 0xf0) + ((val) >> 4))
/* Analog output is a voltage, and scaled to millivolts. The datasheet
* indicates that the DAC could be used to drive the fans, but in our
* example board (Arima HDAMA) it isn't connected to the fans at all.
*/
#define DAC_TO_REG(val) (SENSORS_LIMIT(((((val)*255)+500)/2500), 0, 255))
#define DAC_FROM_REG(val) (((val)*2500)/255)
/* Chip sampling rates
*
* Some sensors are not updated more frequently than once per second
* so it doesn't make sense to read them more often than that.
* We cache the results and return the saved data if the driver
* is called again before a second has elapsed.
*
* Also, there is significant configuration data for this chip
* So, we keep the config data up to date in the cache
* when it is written and only sample it once every 5 *minutes*
*/
#define ADM1026_DATA_INTERVAL (1 * HZ)
#define ADM1026_CONFIG_INTERVAL (5 * 60 * HZ)
/* We allow for multiple chips in a single system.
*
* For each registered ADM1026, we need to keep state information
* at client->data. The adm1026_data structure is dynamically
* allocated, when a new client structure is allocated. */
struct pwm_data {
u8 pwm;
u8 enable;
u8 auto_pwm_min;
};
struct adm1026_data {
struct device *hwmon_dev;
struct mutex update_lock;
int valid; /* !=0 if following fields are valid */
unsigned long last_reading; /* In jiffies */
unsigned long last_config; /* In jiffies */
u8 in[17]; /* Register value */
u8 in_max[17]; /* Register value */
u8 in_min[17]; /* Register value */
s8 temp[3]; /* Register value */
s8 temp_min[3]; /* Register value */
s8 temp_max[3]; /* Register value */
s8 temp_tmin[3]; /* Register value */
s8 temp_crit[3]; /* Register value */
s8 temp_offset[3]; /* Register value */
u8 fan[8]; /* Register value */
u8 fan_min[8]; /* Register value */
u8 fan_div[8]; /* Decoded value */
struct pwm_data pwm1; /* Pwm control values */
u8 vrm; /* VRM version */
u8 analog_out; /* Register value (DAC) */
long alarms; /* Register encoding, combined */
long alarm_mask; /* Register encoding, combined */
long gpio; /* Register encoding, combined */
long gpio_mask; /* Register encoding, combined */
u8 gpio_config[17]; /* Decoded value */
u8 config1; /* Register value */
u8 config2; /* Register value */
u8 config3; /* Register value */
};
static int adm1026_probe(struct i2c_client *client,
const struct i2c_device_id *id);
static int adm1026_detect(struct i2c_client *client,
struct i2c_board_info *info);
static int adm1026_remove(struct i2c_client *client);
static int adm1026_read_value(struct i2c_client *client, u8 reg);
static int adm1026_write_value(struct i2c_client *client, u8 reg, int value);
static void adm1026_print_gpio(struct i2c_client *client);
static void adm1026_fixup_gpio(struct i2c_client *client);
static struct adm1026_data *adm1026_update_device(struct device *dev);
static void adm1026_init_client(struct i2c_client *client);
static const struct i2c_device_id adm1026_id[] = {
{ "adm1026", 0 },
{ }
};
MODULE_DEVICE_TABLE(i2c, adm1026_id);
static struct i2c_driver adm1026_driver = {
.class = I2C_CLASS_HWMON,
.driver = {
.name = "adm1026",
},
.probe = adm1026_probe,
.remove = adm1026_remove,
.id_table = adm1026_id,
.detect = adm1026_detect,
.address_list = normal_i2c,
};
static int adm1026_read_value(struct i2c_client *client, u8 reg)
{
int res;
if (reg < 0x80) {
/* "RAM" locations */
res = i2c_smbus_read_byte_data(client, reg) & 0xff;
} else {
/* EEPROM, do nothing */
res = 0;
}
return res;
}
static int adm1026_write_value(struct i2c_client *client, u8 reg, int value)
{
int res;
if (reg < 0x80) {
/* "RAM" locations */
res = i2c_smbus_write_byte_data(client, reg, value);
} else {
/* EEPROM, do nothing */
res = 0;
}
return res;
}
static void adm1026_init_client(struct i2c_client *client)
{
int value, i;
struct adm1026_data *data = i2c_get_clientdata(client);
dev_dbg(&client->dev, "Initializing device\n");
/* Read chip config */
data->config1 = adm1026_read_value(client, ADM1026_REG_CONFIG1);
data->config2 = adm1026_read_value(client, ADM1026_REG_CONFIG2);
data->config3 = adm1026_read_value(client, ADM1026_REG_CONFIG3);
/* Inform user of chip config */
dev_dbg(&client->dev, "ADM1026_REG_CONFIG1 is: 0x%02x\n",
data->config1);
if ((data->config1 & CFG1_MONITOR) == 0) {
dev_dbg(&client->dev, "Monitoring not currently "
"enabled.\n");
}
if (data->config1 & CFG1_INT_ENABLE) {
dev_dbg(&client->dev, "SMBALERT interrupts are "
"enabled.\n");
}
if (data->config1 & CFG1_AIN8_9) {
dev_dbg(&client->dev, "in8 and in9 enabled. "
"temp3 disabled.\n");
} else {
dev_dbg(&client->dev, "temp3 enabled. in8 and "
"in9 disabled.\n");
}
if (data->config1 & CFG1_THERM_HOT) {
dev_dbg(&client->dev, "Automatic THERM, PWM, "
"and temp limits enabled.\n");
}
if (data->config3 & CFG3_GPIO16_ENABLE) {
dev_dbg(&client->dev, "GPIO16 enabled. THERM "
"pin disabled.\n");
} else {
dev_dbg(&client->dev, "THERM pin enabled. "
"GPIO16 disabled.\n");
}
if (data->config3 & CFG3_VREF_250) {
dev_dbg(&client->dev, "Vref is 2.50 Volts.\n");
} else {
dev_dbg(&client->dev, "Vref is 1.82 Volts.\n");
}
/* Read and pick apart the existing GPIO configuration */
value = 0;
for (i = 0;i <= 15;++i) {
if ((i & 0x03) == 0) {
value = adm1026_read_value(client,
ADM1026_REG_GPIO_CFG_0_3 + i/4);
}
data->gpio_config[i] = value & 0x03;
value >>= 2;
}
data->gpio_config[16] = (data->config3 >> 6) & 0x03;
/* ... and then print it */
adm1026_print_gpio(client);
/* If the user asks us to reprogram the GPIO config, then
* do it now.
*/
if (gpio_input[0] != -1 || gpio_output[0] != -1
|| gpio_inverted[0] != -1 || gpio_normal[0] != -1
|| gpio_fan[0] != -1) {
adm1026_fixup_gpio(client);
}
/* WE INTENTIONALLY make no changes to the limits,
* offsets, pwms, fans and zones. If they were
* configured, we don't want to mess with them.
* If they weren't, the default is 100% PWM, no
* control and will suffice until 'sensors -s'
* can be run by the user. We DO set the default
* value for pwm1.auto_pwm_min to its maximum
* so that enabling automatic pwm fan control
* without first setting a value for pwm1.auto_pwm_min
* will not result in potentially dangerous fan speed decrease.
*/
data->pwm1.auto_pwm_min=255;
/* Start monitoring */
value = adm1026_read_value(client, ADM1026_REG_CONFIG1);
/* Set MONITOR, clear interrupt acknowledge and s/w reset */
value = (value | CFG1_MONITOR) & (~CFG1_INT_CLEAR & ~CFG1_RESET);
dev_dbg(&client->dev, "Setting CONFIG to: 0x%02x\n", value);
data->config1 = value;
adm1026_write_value(client, ADM1026_REG_CONFIG1, value);
/* initialize fan_div[] to hardware defaults */
value = adm1026_read_value(client, ADM1026_REG_FAN_DIV_0_3) |
(adm1026_read_value(client, ADM1026_REG_FAN_DIV_4_7) << 8);
for (i = 0;i <= 7;++i) {
data->fan_div[i] = DIV_FROM_REG(value & 0x03);
value >>= 2;
}
}
static void adm1026_print_gpio(struct i2c_client *client)
{
struct adm1026_data *data = i2c_get_clientdata(client);
int i;
dev_dbg(&client->dev, "GPIO config is:\n");
for (i = 0;i <= 7;++i) {
if (data->config2 & (1 << i)) {
dev_dbg(&client->dev, "\t%sGP%s%d\n",
data->gpio_config[i] & 0x02 ? "" : "!",
data->gpio_config[i] & 0x01 ? "OUT" : "IN",
i);
} else {
dev_dbg(&client->dev, "\tFAN%d\n", i);
}
}
for (i = 8;i <= 15;++i) {
dev_dbg(&client->dev, "\t%sGP%s%d\n",
data->gpio_config[i] & 0x02 ? "" : "!",
data->gpio_config[i] & 0x01 ? "OUT" : "IN",
i);
}
if (data->config3 & CFG3_GPIO16_ENABLE) {
dev_dbg(&client->dev, "\t%sGP%s16\n",
data->gpio_config[16] & 0x02 ? "" : "!",
data->gpio_config[16] & 0x01 ? "OUT" : "IN");
} else {
/* GPIO16 is THERM */
dev_dbg(&client->dev, "\tTHERM\n");
}
}
static void adm1026_fixup_gpio(struct i2c_client *client)
{
struct adm1026_data *data = i2c_get_clientdata(client);
int i;
int value;
/* Make the changes requested. */
/* We may need to unlock/stop monitoring or soft-reset the
* chip before we can make changes. This hasn't been
* tested much. FIXME
*/
/* Make outputs */
for (i = 0;i <= 16;++i) {
if (gpio_output[i] >= 0 && gpio_output[i] <= 16) {
data->gpio_config[gpio_output[i]] |= 0x01;
}
/* if GPIO0-7 is output, it isn't a FAN tach */
if (gpio_output[i] >= 0 && gpio_output[i] <= 7) {
data->config2 |= 1 << gpio_output[i];
}
}
/* Input overrides output */
for (i = 0;i <= 16;++i) {
if (gpio_input[i] >= 0 && gpio_input[i] <= 16) {
data->gpio_config[gpio_input[i]] &= ~ 0x01;
}
/* if GPIO0-7 is input, it isn't a FAN tach */
if (gpio_input[i] >= 0 && gpio_input[i] <= 7) {
data->config2 |= 1 << gpio_input[i];
}
}
/* Inverted */
for (i = 0;i <= 16;++i) {
if (gpio_inverted[i] >= 0 && gpio_inverted[i] <= 16) {
data->gpio_config[gpio_inverted[i]] &= ~ 0x02;
}
}
/* Normal overrides inverted */
for (i = 0;i <= 16;++i) {
if (gpio_normal[i] >= 0 && gpio_normal[i] <= 16) {
data->gpio_config[gpio_normal[i]] |= 0x02;
}
}
/* Fan overrides input and output */
for (i = 0;i <= 7;++i) {
if (gpio_fan[i] >= 0 && gpio_fan[i] <= 7) {
data->config2 &= ~(1 << gpio_fan[i]);
}
}
/* Write new configs to registers */
adm1026_write_value(client, ADM1026_REG_CONFIG2, data->config2);
data->config3 = (data->config3 & 0x3f)
| ((data->gpio_config[16] & 0x03) << 6);
adm1026_write_value(client, ADM1026_REG_CONFIG3, data->config3);
for (i = 15, value = 0;i >= 0;--i) {
value <<= 2;
value |= data->gpio_config[i] & 0x03;
if ((i & 0x03) == 0) {
adm1026_write_value(client,
ADM1026_REG_GPIO_CFG_0_3 + i/4,
value);
value = 0;
}
}
/* Print the new config */
adm1026_print_gpio(client);
}
static struct adm1026_data *adm1026_update_device(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct adm1026_data *data = i2c_get_clientdata(client);
int i;
long value, alarms, gpio;
mutex_lock(&data->update_lock);
if (!data->valid
|| time_after(jiffies, data->last_reading + ADM1026_DATA_INTERVAL)) {
/* Things that change quickly */
dev_dbg(&client->dev, "Reading sensor values\n");
for (i = 0;i <= 16;++i) {
data->in[i] =
adm1026_read_value(client, ADM1026_REG_IN[i]);
}
for (i = 0;i <= 7;++i) {
data->fan[i] =
adm1026_read_value(client, ADM1026_REG_FAN(i));
}
for (i = 0;i <= 2;++i) {
/* NOTE: temp[] is s8 and we assume 2's complement
* "conversion" in the assignment */
data->temp[i] =
adm1026_read_value(client, ADM1026_REG_TEMP[i]);
}
data->pwm1.pwm = adm1026_read_value(client,
ADM1026_REG_PWM);
data->analog_out = adm1026_read_value(client,
ADM1026_REG_DAC);
/* GPIO16 is MSbit of alarms, move it to gpio */
alarms = adm1026_read_value(client, ADM1026_REG_STATUS4);
gpio = alarms & 0x80 ? 0x0100 : 0; /* GPIO16 */
alarms &= 0x7f;
alarms <<= 8;
alarms |= adm1026_read_value(client, ADM1026_REG_STATUS3);
alarms <<= 8;
alarms |= adm1026_read_value(client, ADM1026_REG_STATUS2);
alarms <<= 8;
alarms |= adm1026_read_value(client, ADM1026_REG_STATUS1);
data->alarms = alarms;
/* Read the GPIO values */
gpio |= adm1026_read_value(client,
ADM1026_REG_GPIO_STATUS_8_15);
gpio <<= 8;
gpio |= adm1026_read_value(client,
ADM1026_REG_GPIO_STATUS_0_7);
data->gpio = gpio;
data->last_reading = jiffies;
}; /* last_reading */
if (!data->valid ||
time_after(jiffies, data->last_config + ADM1026_CONFIG_INTERVAL)) {
/* Things that don't change often */
dev_dbg(&client->dev, "Reading config values\n");
for (i = 0;i <= 16;++i) {
data->in_min[i] = adm1026_read_value(client,
ADM1026_REG_IN_MIN[i]);
data->in_max[i] = adm1026_read_value(client,
ADM1026_REG_IN_MAX[i]);
}
value = adm1026_read_value(client, ADM1026_REG_FAN_DIV_0_3)
| (adm1026_read_value(client, ADM1026_REG_FAN_DIV_4_7)
<< 8);
for (i = 0;i <= 7;++i) {
data->fan_min[i] = adm1026_read_value(client,
ADM1026_REG_FAN_MIN(i));
data->fan_div[i] = DIV_FROM_REG(value & 0x03);
value >>= 2;
}
for (i = 0; i <= 2; ++i) {
/* NOTE: temp_xxx[] are s8 and we assume 2's
* complement "conversion" in the assignment
*/
data->temp_min[i] = adm1026_read_value(client,
ADM1026_REG_TEMP_MIN[i]);
data->temp_max[i] = adm1026_read_value(client,
ADM1026_REG_TEMP_MAX[i]);
data->temp_tmin[i] = adm1026_read_value(client,
ADM1026_REG_TEMP_TMIN[i]);
data->temp_crit[i] = adm1026_read_value(client,
ADM1026_REG_TEMP_THERM[i]);
data->temp_offset[i] = adm1026_read_value(client,
ADM1026_REG_TEMP_OFFSET[i]);
}
/* Read the STATUS/alarm masks */
alarms = adm1026_read_value(client, ADM1026_REG_MASK4);
gpio = alarms & 0x80 ? 0x0100 : 0; /* GPIO16 */
alarms = (alarms & 0x7f) << 8;
alarms |= adm1026_read_value(client, ADM1026_REG_MASK3);
alarms <<= 8;
alarms |= adm1026_read_value(client, ADM1026_REG_MASK2);
alarms <<= 8;
alarms |= adm1026_read_value(client, ADM1026_REG_MASK1);
data->alarm_mask = alarms;
/* Read the GPIO values */
gpio |= adm1026_read_value(client,
ADM1026_REG_GPIO_MASK_8_15);
gpio <<= 8;
gpio |= adm1026_read_value(client, ADM1026_REG_GPIO_MASK_0_7);
data->gpio_mask = gpio;
/* Read various values from CONFIG1 */
data->config1 = adm1026_read_value(client,
ADM1026_REG_CONFIG1);
if (data->config1 & CFG1_PWM_AFC) {
data->pwm1.enable = 2;
data->pwm1.auto_pwm_min =
PWM_MIN_FROM_REG(data->pwm1.pwm);
}
/* Read the GPIO config */
data->config2 = adm1026_read_value(client,
ADM1026_REG_CONFIG2);
data->config3 = adm1026_read_value(client,
ADM1026_REG_CONFIG3);
data->gpio_config[16] = (data->config3 >> 6) & 0x03;
value = 0;
for (i = 0;i <= 15;++i) {
if ((i & 0x03) == 0) {
value = adm1026_read_value(client,
ADM1026_REG_GPIO_CFG_0_3 + i/4);
}
data->gpio_config[i] = value & 0x03;
value >>= 2;
}
data->last_config = jiffies;
}; /* last_config */
data->valid = 1;
mutex_unlock(&data->update_lock);
return data;
}
static ssize_t show_in(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
int nr = sensor_attr->index;
struct adm1026_data *data = adm1026_update_device(dev);
return sprintf(buf, "%d\n", INS_FROM_REG(nr, data->in[nr]));
}
static ssize_t show_in_min(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
int nr = sensor_attr->index;
struct adm1026_data *data = adm1026_update_device(dev);
return sprintf(buf, "%d\n", INS_FROM_REG(nr, data->in_min[nr]));
}
static ssize_t set_in_min(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
int nr = sensor_attr->index;
struct i2c_client *client = to_i2c_client(dev);
struct adm1026_data *data = i2c_get_clientdata(client);
int val = simple_strtol(buf, NULL, 10);
mutex_lock(&data->update_lock);
data->in_min[nr] = INS_TO_REG(nr, val);
adm1026_write_value(client, ADM1026_REG_IN_MIN[nr], data->in_min[nr]);
mutex_unlock(&data->update_lock);
return count;
}
static ssize_t show_in_max(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
int nr = sensor_attr->index;
struct adm1026_data *data = adm1026_update_device(dev);
return sprintf(buf, "%d\n", INS_FROM_REG(nr, data->in_max[nr]));
}
static ssize_t set_in_max(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
int nr = sensor_attr->index;
struct i2c_client *client = to_i2c_client(dev);
struct adm1026_data *data = i2c_get_clientdata(client);
int val = simple_strtol(buf, NULL, 10);
mutex_lock(&data->update_lock);
data->in_max[nr] = INS_TO_REG(nr, val);
adm1026_write_value(client, ADM1026_REG_IN_MAX[nr], data->in_max[nr]);
mutex_unlock(&data->update_lock);
return count;
}
#define in_reg(offset) \
static SENSOR_DEVICE_ATTR(in##offset##_input, S_IRUGO, show_in, \
NULL, offset); \
static SENSOR_DEVICE_ATTR(in##offset##_min, S_IRUGO | S_IWUSR, \
show_in_min, set_in_min, offset); \
static SENSOR_DEVICE_ATTR(in##offset##_max, S_IRUGO | S_IWUSR, \
show_in_max, set_in_max, offset);
in_reg(0);
in_reg(1);
in_reg(2);
in_reg(3);
in_reg(4);
in_reg(5);
in_reg(6);
in_reg(7);
in_reg(8);
in_reg(9);
in_reg(10);
in_reg(11);
in_reg(12);
in_reg(13);
in_reg(14);
in_reg(15);
static ssize_t show_in16(struct device *dev, struct device_attribute *attr, char *buf)
{
struct adm1026_data *data = adm1026_update_device(dev);
return sprintf(buf, "%d\n", INS_FROM_REG(16, data->in[16]) -
NEG12_OFFSET);
}
static ssize_t show_in16_min(struct device *dev, struct device_attribute *attr, char *buf)
{
struct adm1026_data *data = adm1026_update_device(dev);
return sprintf(buf, "%d\n", INS_FROM_REG(16, data->in_min[16])
- NEG12_OFFSET);
}
static ssize_t set_in16_min(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct adm1026_data *data = i2c_get_clientdata(client);
int val = simple_strtol(buf, NULL, 10);
mutex_lock(&data->update_lock);
data->in_min[16] = INS_TO_REG(16, val + NEG12_OFFSET);
adm1026_write_value(client, ADM1026_REG_IN_MIN[16], data->in_min[16]);
mutex_unlock(&data->update_lock);
return count;
}
static ssize_t show_in16_max(struct device *dev, struct device_attribute *attr, char *buf)
{
struct adm1026_data *data = adm1026_update_device(dev);
return sprintf(buf, "%d\n", INS_FROM_REG(16, data->in_max[16])
- NEG12_OFFSET);
}
static ssize_t set_in16_max(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct adm1026_data *data = i2c_get_clientdata(client);
int val = simple_strtol(buf, NULL, 10);
mutex_lock(&data->update_lock);
data->in_max[16] = INS_TO_REG(16, val+NEG12_OFFSET);
adm1026_write_value(client, ADM1026_REG_IN_MAX[16], data->in_max[16]);
mutex_unlock(&data->update_lock);
return count;
}
static SENSOR_DEVICE_ATTR(in16_input, S_IRUGO, show_in16, NULL, 16);
static SENSOR_DEVICE_ATTR(in16_min, S_IRUGO | S_IWUSR, show_in16_min, set_in16_min, 16);
static SENSOR_DEVICE_ATTR(in16_max, S_IRUGO | S_IWUSR, show_in16_max, set_in16_max, 16);
/* Now add fan read/write functions */
static ssize_t show_fan(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
int nr = sensor_attr->index;
struct adm1026_data *data = adm1026_update_device(dev);
return sprintf(buf, "%d\n", FAN_FROM_REG(data->fan[nr],
data->fan_div[nr]));
}
static ssize_t show_fan_min(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
int nr = sensor_attr->index;
struct adm1026_data *data = adm1026_update_device(dev);
return sprintf(buf, "%d\n", FAN_FROM_REG(data->fan_min[nr],
data->fan_div[nr]));
}
static ssize_t set_fan_min(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
int nr = sensor_attr->index;
struct i2c_client *client = to_i2c_client(dev);
struct adm1026_data *data = i2c_get_clientdata(client);
int val = simple_strtol(buf, NULL, 10);
mutex_lock(&data->update_lock);
data->fan_min[nr] = FAN_TO_REG(val, data->fan_div[nr]);
adm1026_write_value(client, ADM1026_REG_FAN_MIN(nr),
data->fan_min[nr]);
mutex_unlock(&data->update_lock);
return count;
}
#define fan_offset(offset) \
static SENSOR_DEVICE_ATTR(fan##offset##_input, S_IRUGO, show_fan, NULL, \
offset - 1); \
static SENSOR_DEVICE_ATTR(fan##offset##_min, S_IRUGO | S_IWUSR, \
show_fan_min, set_fan_min, offset - 1);
fan_offset(1);
fan_offset(2);
fan_offset(3);
fan_offset(4);
fan_offset(5);
fan_offset(6);
fan_offset(7);
fan_offset(8);
/* Adjust fan_min to account for new fan divisor */
static void fixup_fan_min(struct device *dev, int fan, int old_div)
{
struct i2c_client *client = to_i2c_client(dev);
struct adm1026_data *data = i2c_get_clientdata(client);
int new_min;
int new_div = data->fan_div[fan];
/* 0 and 0xff are special. Don't adjust them */
if (data->fan_min[fan] == 0 || data->fan_min[fan] == 0xff) {
return;
}
new_min = data->fan_min[fan] * old_div / new_div;
new_min = SENSORS_LIMIT(new_min, 1, 254);
data->fan_min[fan] = new_min;
adm1026_write_value(client, ADM1026_REG_FAN_MIN(fan), new_min);
}
/* Now add fan_div read/write functions */
static ssize_t show_fan_div(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
int nr = sensor_attr->index;
struct adm1026_data *data = adm1026_update_device(dev);
return sprintf(buf, "%d\n", data->fan_div[nr]);
}
static ssize_t set_fan_div(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
int nr = sensor_attr->index;
struct i2c_client *client = to_i2c_client(dev);
struct adm1026_data *data = i2c_get_clientdata(client);
int val, orig_div, new_div, shift;
val = simple_strtol(buf, NULL, 10);
new_div = DIV_TO_REG(val);
if (new_div == 0) {
return -EINVAL;
}
mutex_lock(&data->update_lock);
orig_div = data->fan_div[nr];
data->fan_div[nr] = DIV_FROM_REG(new_div);
if (nr < 4) { /* 0 <= nr < 4 */
shift = 2 * nr;
adm1026_write_value(client, ADM1026_REG_FAN_DIV_0_3,
((DIV_TO_REG(orig_div) & (~(0x03 << shift))) |
(new_div << shift)));
} else { /* 3 < nr < 8 */
shift = 2 * (nr - 4);
adm1026_write_value(client, ADM1026_REG_FAN_DIV_4_7,
((DIV_TO_REG(orig_div) & (~(0x03 << (2 * shift)))) |
(new_div << shift)));
}
if (data->fan_div[nr] != orig_div) {
fixup_fan_min(dev, nr, orig_div);
}
mutex_unlock(&data->update_lock);
return count;
}
#define fan_offset_div(offset) \
static SENSOR_DEVICE_ATTR(fan##offset##_div, S_IRUGO | S_IWUSR, \
show_fan_div, set_fan_div, offset - 1);
fan_offset_div(1);
fan_offset_div(2);
fan_offset_div(3);
fan_offset_div(4);
fan_offset_div(5);
fan_offset_div(6);
fan_offset_div(7);
fan_offset_div(8);
/* Temps */
static ssize_t show_temp(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
int nr = sensor_attr->index;
struct adm1026_data *data = adm1026_update_device(dev);
return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp[nr]));
}
static ssize_t show_temp_min(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
int nr = sensor_attr->index;
struct adm1026_data *data = adm1026_update_device(dev);
return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp_min[nr]));
}
static ssize_t set_temp_min(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
int nr = sensor_attr->index;
struct i2c_client *client = to_i2c_client(dev);
struct adm1026_data *data = i2c_get_clientdata(client);
int val = simple_strtol(buf, NULL, 10);
mutex_lock(&data->update_lock);
data->temp_min[nr] = TEMP_TO_REG(val);
adm1026_write_value(client, ADM1026_REG_TEMP_MIN[nr],
data->temp_min[nr]);
mutex_unlock(&data->update_lock);
return count;
}
static ssize_t show_temp_max(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
int nr = sensor_attr->index;
struct adm1026_data *data = adm1026_update_device(dev);