-
Notifications
You must be signed in to change notification settings - Fork 0
/
README.kconfig
158 lines (116 loc) · 6 KB
/
README.kconfig
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
Kconfig in U-Boot
=================
This document describes the configuration infrastructure of U-Boot.
The conventional configuration was replaced by Kconfig at v2014.10-rc1 release.
Language Specification
----------------------
Kconfig originates in Linux Kernel.
See the file "Documentation/kbuild/kconfig*.txt" in your Linux Kernel
source directory for a basic specification of Kconfig.
Difference from Linux's Kconfig
-------------------------------
Here are some worth-mentioning configuration targets.
- silentoldconfig
This target updates .config, include/generated/autoconf.h and
include/configs/* as in Linux. In U-Boot, it also does the following
for the compatibility with the old configuration system:
* create a symbolic link "arch/${ARCH}/include/asm/arch" pointing to
the SoC/CPU specific header directory
* create include/config.h
* create include/autoconf.mk
* create spl/include/autoconf.mk (SPL and TPL only)
* create tpl/include/autoconf.mk (TPL only)
If we could completely switch to Kconfig in a long run
(i.e. remove all the include/configs/*.h), those additional processings
above would be removed.
- defconfig
In U-Boot, "make defconfig" is a shorthand of "make sandbox_defconfig"
- <board>_defconfig
Now it works as in Linux.
The prefixes such as "+S:" in *_defconfig are deprecated.
You can simply remove the prefixes. Do not add them for new boards.
- <board>_config
This does not exist in Linux's Kconfig.
"make <board>_config" works the same as "make <board>_defconfig".
Prior to Kconfig, in U-Boot, "make <board>_config" was used for the
configuration. It is still supported for backward compatibility, so
we do not need to update the distro recipes.
The other configuration targets work as in Linux Kernel.
Migration steps to Kconfig
--------------------------
Prior to Kconfig, the C preprocessor based board configuration had been used
in U-Boot.
Although Kconfig was introduced and some configs have been moved to Kconfig,
many of configs are still defined in C header files. It will take a very
long term to move all of them to Kconfig. In the interim, the two different
configuration infrastructures should coexist.
The configuration files are generated by both Kconfig and the old preprocessor
based configuration as follows:
Configuration files for use in C sources
- include/generated/autoconf.h (generated by Kconfig for Normal)
- include/configs/<board>.h (exists for all boards)
Configuration file for use in makefiles
- include/config/auto.conf (generated by Kconfig)
- include/autoconf.mk (generated by the old config for Normal)
- spl/include/autoconfig.mk (generated by the old config for SPL)
- tpl/include/autoconfig.mk (generated by the old config for TPL)
When adding a new CONFIG macro, it is highly recommended to add it to Kconfig
rather than to a header file.
Conversion from boards.cfg to Kconfig
-------------------------------------
Prior to Kconfig, boards.cfg was a primary database that contained Arch, CPU,
SoC, etc. of all the supported boards. It was deleted when switching to
Kconfig. Each field of boards.cfg was converted as follows:
Status -> "S:" entry of MAINTAINERS
Arch -> CONFIG_SYS_ARCH defined by Kconfig
CPU -> CONFIG_SYS_CPU defined by Kconfig
SoC -> CONFIG_SYS_SOC defined by Kconfig
Vendor -> CONFIG_SYS_VENDOR defined by Kconfig
Board -> CONFIG_SYS_BOARD defined by Kconfig
Target -> File name of defconfig (configs/<target>_defconfig)
Options -> CONFIG_SYS_EXTRA_OPTIONS defined by Kconfig
Maintainers -> "M:" entry of MAINTAINERS
Tips to add/remove boards
-------------------------
When adding a new board, the following steps are generally needed:
[1] Add a header file include/configs/<target>.h
[2] Make sure to define necessary CONFIG_SYS_* in Kconfig:
Define CONFIG_SYS_CPU="cpu" to compile arch/<arch>/cpu/<cpu>
Define CONFIG_SYS_SOC="soc" to compile arch/<arch>/cpu/<cpu>/<soc>
Define CONFIG_SYS_VENDOR="vendor" to compile board/<vendor>/common/*
and board/<vendor>/<board>/*
Define CONFIG_SYS_BOARD="board" to compile board/<board>/*
(or board/<vendor>/<board>/* if CONFIG_SYS_VENDOR is defined)
Define CONFIG_SYS_CONFIG_NAME="target" to include
include/configs/<target>.h
[3] Add a new entry to the board select menu in Kconfig.
The board select menu is located in arch/<arch>/Kconfig or
arch/<arch>/*/Kconfig.
[4] Add a MAINTAINERS file
It is generally placed at board/<board>/MAINTAINERS or
board/<vendor>/<board>/MAINTAINERS
[5] Add configs/<target>_defconfig
When removing an obsolete board, the following steps are generally needed:
[1] Remove configs/<target>_defconfig
[2] Remove include/configs/<target>.h if it is not used by any other boards
[3] Remove board/<vendor>/<board>/* or board/<board>/* if it is not used
by any other boards
[4] Update MAINTAINERS if necessary
[5] Remove the unused entry from the board select menu in Kconfig
[6] Add an entry to doc/README.scrapyard
TODO
----
- The option field of boards.cfg, which was used for the pre-Kconfig
configuration, moved to CONFIG_SYS_EXTRA_OPTIONS verbatim now.
Board maintainers are expected to implement proper Kconfig options
and switch over to them. Eventually CONFIG_SYS_EXTRA_OPTIONS will go away.
CONFIG_SYS_EXTRA_OPTIONS should not be used for new boards.
- In the pre-Kconfig, a single board had multiple entries in the boards.cfg
file with differences in the option fields. The corresponding defconfig
files were auto-generated when switching to Kconfig. Now we have too many
defconfig files compared with the number of the supported boards. It is
recommended to have only one defconfig per board and allow users to select
the config options.
- Move the config macros in header files to Kconfig. When we move at least
macros used in makefiles, we can drop include/autoconfig.mk, which makes
the build scripts much simpler.