Deprecation Notice

This project served a need originally, but I no longer use or maintain it. I use and highly recommend ESPHome, which supports everything this project can handle and much, much more. ESPHome has a local API with a native integration with Home Assistant, but can also be used separately from Home Assistant using the MQTT component.

As an example, this is an initial configuration you could use in ESPHome to replace this whole project for an RGB light using MQTT:

esphome:
  name: rgb-light # Update this.

esp8266:
  # Update to match your board. See: https://esphome.io/components/esp8266.html
  board: d1_mini

wifi:
  ssid: wifi_ssid # Update this (ideally using !secrets)
  password: wifi_password # Update this (ideally using !secrets)

mqtt:
  broker: 192.168.1.2 # Update this.
  username: username # Update this (ideally using !secrets)
  password: password # Update this (ideally using !secrets)

logger:
ota:

output:
  - platform: esp8266_pwm
    id: red_pin
    pin: GPIO0 # Update this.
  - platform: esp8266_pwm
    id: green_pin
    pin: GPIO2 # Update this.
  - platform: esp8266_pwm
    id: blue_pin
    pin: GPIO3 # Update this.

light:
  - platform: rgb
    name: "RGB Light"
    red: red_pin
    green: green_pin
    blue: blue_pin

See the relevant light components for more help:

• Monochromatic Light
• RGB Light
• RGBW Light

Thank you for using this repo and providing feedback. Going forward, I've moved some of my development attention to supporting ESPHome.

Previous README below.

---

ESP8266 MQTT RGB(W) Lights Using JSON for Home Assistant

This project adds an easy way to create DIY lighting for Home Assistant, an amazing, extensible, open-source home automation system.

I was frustrated that the built-in MQTT light didn't support transitions (fading between colors/brightnesses), and that it uses multiple separate calls to set the different values (state (on/off), brightness, color), so I decided to make my own version. As of version 0.26, the MQTT JSON light platform has been merged into Home Assistant.

By sending a JSON payload (in an MQTT message), Home Assistant can include whichever fields are necessary, reducing the round trips from 3 to 1. For example, this is a sample payload including most of the fields:

{
  "state": "ON",
  "brightness": 120,
  "color": {
    "r": 255,
    "g": 100,
    "b": 100
  },
  "transition": 5
}

Installation/Configuration

To set this system up, you need to configure the MQTT light component in Home Assistant and set up a light to control. This guide assumes that you already have Home Assistant set up and running. If not, see the installation guides here.

The Home Assistant Side

1. In your configuration.yaml, add the following, depending on the supported features of the light:

   # Only one color:
   light:
     - platform: mqtt
       schema: json
       name: mqtt_json_light_1
       state_topic: "home/json_brightness"
       command_topic: "home/json_brightness/set"
       brightness: true
       effect: true
       effect_list: [flash]
       optimistic: false
       qos: 0
   
   # RGB:
   light:
     - platform: mqtt
       schema: json
       name: mqtt_json_light_2
       state_topic: "home/rgb1"
       command_topic: "home/rgb1/set"
       brightness: true
       rgb: true
       effect: true
       effect_list: [colorfade_slow, colorfade_fast, flash]
       optimistic: false
       qos: 0
   
   # RGBW:
   light:
     - platform: mqtt
       schema: json
       name: mqtt_json_light_3
       state_topic: "home/rgbw1"
       command_topic: "home/rgbw1/set"
       brightness: true
       rgb: true
       white_value: true
       effect: true
       effect_list: [colorfade_slow, colorfade_fast, flash]
       optimistic: false
       qos: 0

2. Set the name, state_topic, and command_topic to values that make sense for you.

3. Restart Home Assistant. Depending on how you installed it, the process differs. For a Raspberry Pi All-in-One install, use sudo systemctl restart home-assistant.service (or just restart the Pi).

The Light Side

I'm using ESP8266-01 microcontrollers for my lights because they are so cheap and small. The downside of the size and price is that programming them can be a bit of a hassle. There are many sites that go into detail, so I won't do it here. You'll need an ESP set up to work with the Arduino IDE. See the readme here for instructions. Another good device to work with is the Wemos D1 Mini, which has a built-in micro-USB port and is much easier to program.

1. Using the Library Manager in the Arduino IDE, install ArduinoJSON and PubSubClient. You can find the Library Manager in the "Sketch" menu under "Include Library" -> "Manage Libraries..."

• NOTE:: At the moment, this project only supports ArduinoJSON version 5. The default is now version 6, so you'll have to specify the version to install in the dropdown in the Library Manager window.

2. Open the mqtt_esp8266_light project in the Arduino IDE.
3. Update the config-sample.h file with your settings for LED type, pin numbers, WiFi settings, and MQTT settings.
4. Review the comments to help with the options. For the CONFIG_STRIP option, choose one of BRIGHTNESS, RGB, or RGBW.
5. Ensure that the CONFIG_MQTT_CLIENT_ID setting is a unique value for your network.
6. Set CONFIG_MQTT_TOPIC_STATE and CONFIG_MQTT_TOPIC_SET to match the values you put in your configuration.yaml.
7. Save the configuration file as config.h.
8. Open the .ino file in the Arduino IDE and upload to an ESP with the correct connections.

About the DEPRECATED Folder

Originally, there were separate Arduino sketches for each of the supported light types. This quickly became redundant and hard-to-maintain, so the new, unified sketch was created.

Please use this (mqtt_esp8266_light) sketch going forward. The deprecated sketches will not receive new features and will be removed from the project in the future.

Wiring

For an RGB LED strip using N-MOSFETs for control, you'll want to wire it similar to this:

Note that the MOSFETs have pull-up resistors in this setup. This means that the lights may flash on when the module resets, but it was necessary to keep the ESP's pins in the right start state.