klipper-macros

This is a collection of macros for the Klipper 3D printer firmware. I originally created this repo just to have a consistent set of macros shared between my own 3D printers. But since I've found them useful, I thought other people might as well.

What can I do with these?

Most of these macros improve basic functionality (e.g. selectable build sheets ) and Klipper compatability with g-code targeting Marlin printers. However, there are also some nice extras:

• Schedule commands at heights and layer changes - This is similar to what your slicer can already do, but I find it simpler, and you can schedule these commands while a print is active. As an example of usage, I added an LCD menu item to pause the print at the next layer change. This way the pause won't mar the print by e.g. pausing inside an external perimeter.
• Dynamically scale heaters and fans - This makes it easy to do things like persistently adjust fan settings during a live print, or maintain simpler slicer profiles by moving things like a heater bump for a hardened steel nozzle into state stored on the printer.
• Cleaner LCD menu interface - I've simplified the menus and provided a much easier way to customize materials in the LCD menu (or at least I think so). I've also added confirmation dialogs for commands that would abort an active print.
• Optimized mesh bed leveling - Probes only within the printed area, which can save a lot of time on smaller prints.
• Automated purge lines - Set the desired extrusion length as variable_start_purge_length in your config and a correctly sized set of purge lines will be extruded in front of the print area immediately before the print starts.

A few warnings...

• BACK UP YOUR FULL CONFIG BEFORE MAKING ANY CHANGES!!! I've seen so many newcomers desperately looking for help on public forums because they didn't have a good config to fall back to after messing up their current config while experimenting with other people's macros. You'll save yourself and everyone else a whole lot of time and nuisance if you just make sure you always have a working config backed up.
• You really should avoid custom macros like this until you're comfortable using Klipper with a basic config. Advanced Klipper macros tend to rely extensively on monkey patching, which can lead to problems with unusual configurations or when mixing macros from various sources. So, you really want to know what you're doing before including someone else's macros—particularly when including macros with overlapping functionality from different sources.
• You must have a heater_bed, extruder, and other sections listed below configured, otherwise the macros will force a printer shutdown at startup. Unfortunately, the Klipper macro system doesn't have a more graceful way of handling this sort of thing.
• The multi-extruder and chamber heater functionality is very under-tested and may have bugs, since I haven't used it much at all. Patches welcome.
• There's probably other stuff I haven't used enough to test thoroughly, so use these macros at your own risk.

Installation

To install the macros, first clone this repository inside of your printer_data/config directory with the following command.

git clone https://github.com/jschuh/klipper-macros.git

Then paste the below sections into your printer.cfg to get started. Or even better, paste all of it into a seperate file in the same path as your config, and include that file. That will make it easier if you want to remove these macros in the future.

You may need to customize some settings for your own config. All configurable settings are in globals.cfg, and can be overridden by creating a corresponding variable with a new value in your [gcode_macro _km_options] section.

Note: The paths in this README follow Moonraker's data folder structure. You may need to change them if you are using a different structure.

Note: Make sure you don't currently have any macros that provide the same basic function as the macros in this repository (e.g. the default Mainsail or fluidd macros). As a rule, you should avoid using multiple sets of macros that override the same base macro (unless you really know what you're doing) because conflicting macros can cause all sorts of weird and frustrating problems.

Note: If you have a [homing_override] section you will need to update any G28 commands in the gcode part to use G28.6245197 instead (which is the renamed version of Klipper's built-in G28). Failure to do this will cause G28 commands to error out with the message Macro G28 called recursively.

Klipper Setup

# All customizations are documented in globals.cfg. Just copy a variable from
# there into the section below, and change the value to meet your needs.

[gcode_macro _km_options]
# These are examples of some likely customizations:
# Any sheets in the below list will be available with a configurable offset.
#variable_bed_surfaces: ['smooth_1','texture_1']
# Length (in mm) of filament to load (bowden tubes will be longer).
#variable_load_length: 90.0
# Hide the Octoprint LCD menu since I don't use it.
#variable_menu_show_octoprint: False
# Customize the filament menus (up to 10 entries).
#variable_menu_temperature: [
#  {'name' : 'PLA',  'extruder' : 200.0, 'bed' : 60.0},
#  {'name' : 'PETG', 'extruder' : 230.0, 'bed' : 85.0},
#  {'name' : 'ABS',  'extruder' : 245.0, 'bed' : 110.0, 'chamber' : 60}]
# Length of filament (in millimeters) to purge at print start.
#variable_start_purge_length: 30 # This value works for most setups.
gcode: # This line is required by Klipper.
# Any code you put here will run at klipper startup, after the initialization
# for these macros. For example, you could uncomment the following line to
# automatically adjust your bed surface offsets to account for any changes made
# to your Z endstop or probe offset.
#  ADJUST_SURFACE_OFFSETS

# This line includes all the standard macros.
[include klipper-macros/*.cfg]
# Uncomment to include features that require specific hardware support.
# LCD menu support for features like bed surface selection and pause next layer.
#[include klipper-macros/optional/lcd_menus.cfg]
# Optimized bed leveling
#[include klipper-macros/optional/bed_mesh.cfg]

# The sections below here are required for the macros to work. If your config
# already has some of these sections you should merge the duplicates into one
# (or if they are identical just remove one of them).
[idle_timeout]
gcode:
  _KM_IDLE_TIMEOUT # This line must be in your idle_timeout section.

[pause_resume]

[respond]

[save_variables]
filename: ~/printer_data/variables.cfg # UPDATE THIS FOR YOUR PATH!!!

[virtual_sdcard]
path: ~/gcode_files # UPDATE THIS FOR YOUR PATH!!!

[display_status]

# Uncomment the sections below if Fluidd complains (because it's confused).
#[gcode_macro CANCEL_PRINT]
#rename_existing: CANCEL_PRINT_FAKE_BASE
#gcode: CANCEL_PRINT_FAKE_BASE {rawparams}

Slicer Configuration

PrusaSlicer / SuperSlicer

PrusaSlicer and its variants are fairly easy to configure. Just open Printer Settings → Custom G-code for your Klipper printer and paste the below text into the relevant sections.

Start G-code

M190 S0
M109 S0
PRINT_START EXTRUDER={first_layer_temperature[initial_tool]} BED=[first_layer_bed_temperature] MESH_MIN={first_layer_print_min[0]},{first_layer_print_min[1]} MESH_MAX={first_layer_print_max[0]},{first_layer_print_max[1]} LAYERS={total_layer_count} NOZZLE_SIZE={nozzle_diameter[0]}

; This is the place to put slicer purge lines if you haven't set a non-zero
; variable_start_purge_length to have START_PRINT automatically purge (e.g. if
; using a Mosaic Palette, which requires the slicer to generate the purge).

End G-code

PRINT_END

Before layer change G-code

;BEFORE_LAYER_CHANGE
;[layer_z]
BEFORE_LAYER_CHANGE HEIGHT=[layer_z] LAYER=[layer_num]

After layer change G-code

;AFTER_LAYER_CHANGE
;[layer_z]
AFTER_LAYER_CHANGE

Ultimaker Cura

Cura is a bit more difficult to configure, and it comes with the following known issues:

• Cura doesn't have proper placeholders for before and after layer changes, so the before triggers all fire and are followed immediately by the after triggers, all of which happens inside the layer change. This probably doesn't matter, but it does mean that you can't use the before and after triggers to avoid running code in the layer change.
• Cura doesn't provide the Z-height of the current layer, so it's inferred from the current nozzle position, which will include the Z-hop if the nozzle is currently raised. This means height based gcode triggers may fire earlier than expected.
• Cura's Insert at layer change fires the After trigger and then the Before trigger (i.e before or after the layer, versus before or after the layer change). These macros and PrusaSlicer do the opposite, which is something to keep in mind if you're used to how Cura does it. Note that these macros do use an Insert at layer change script to force LAYER comment generation, but that doesn't affect the trigger ordering.
• Cura does not provide the first layer bounding rectangle, only the model bounding volume. This means the XY bounding box used to speed up mesh probing may be larger than it needs to be, resulting in bed probing that's not as fast as it could be.

Accepting the caveats, the macros work quite well with Cura if you follow the configuration steps listed below.

Start G-code

M190 S0
M109 S0
PRINT_START EXTRUDER={material_print_temperature_layer_0} BED={material_bed_temperature_layer_0} NOZZLE_SIZE={machine_nozzle_size}

; This is the place to put slicer purge lines if you haven't set a non-zero
; variable_start_purge_length to have START_PRINT automatically purge (e.g. if
; using a Mosaic Palette, which requires the slicer to generate the purge).

End G-code

PRINT_END

Post Processing Plugin

Use the menu item for Extensions → Post Processing → Modify G-Code to open the Post Processing Plugin and add the following four scripts. The scripts must be run in the order listed below and be sure to copy the strings exactly, with no leading or trailing spaces.

Search and Replace

• Search: (\n;(MIN|MAX)X:([^\n]+)\n;\2Y:([^\n]+))
• Replace: \1\nPRINT_START_SET MESH_\2=\3,\4
• Use Regular Expressions: ☑️

Search and Replace

• Search: (\n;LAYER_COUNT:([^\n]+))
• Replace: \1\nINIT_LAYER_GCODE LAYERS=\2\nPRINT_START_SET LAYERS=\2
• Use Regular Expressions: ☑️

Insert at layer change

• When to insert: Before
• G-code to insert: ;BEFORE_LAYER_CHANGE

Search and Replace

• Search: (\n;LAYER:([^\n]+))
• Replace: \1\nBEFORE_LAYER_CHANGE LAYER=\2\nAFTER_LAYER_CHANGE
• Use Regular Expressions: ☑️

Moonraker Configuration

Once you have the macros working and are comfortable using them, you can have Moonraker keep them up to date by adding the following into your moonraker.conf.

[update_manager klipper-macros]
type: git_repo
origin: https://github.com/jschuh/klipper-macros.git
path: ~/printer_data/config/klipper-macros # UPDATE THIS FOR YOUR PATH!!!
primary_branch: main
is_system_service: False
managed_services: klipper

Note: I'd advise against adding the auto-update entries to Moonraker until you have everything working well, because it can make uninstallation a bit harder due to how Moonraker's autoupdate behavior.

Removal

If you choose to uninstall these macros you basically need to reverse the installation steps. However, the most critical parts are listed below.

Klipper Configuration Removal

Ensure that you remove the following from your Klipper config (and any included configs):

• The full [gcode_macro _km_options] section
• Any include sections with klipper-macros in the path
• _KM_IDLE_TIMEOUT in the [idle_timeout] section

If you do not have Moonraker autoupdates configured you can delete the klipper-macros directory with something like the following command (adjusted for your own paths):

rm -rf ~/printer_data/config/klipper-macros

Slicer Configuration Removal

If you do not want to change your slicer config, you should be able to leave it as is, because it generates only a small amount of additional gcode, and the basic parameters should work with any other PRINT_START macros.

Moonraker Configuration Removal

If you've configured Moonraker auto-updates you will need to remove the entire [update_manager klipper-macros] section and restart moonraker prior to deleting the klipper-macros directory, otherwise Moonraker may attempt to recreate it. You may also find that it takes a few Moonraker update checks and restarts before the klipper-macros section disappears from the UI.

Command Reference

Customization

All features are configured by setting variable_ values in the [gcode_macro _km_options] section. All available variables and their purpose are listed in globals.cfg.

Bed Mesh Improvements

BED_MESH_CALIBRATE_FAST

Wraps the Klipper BED_MESH_CALIBRATE command to scale and redistribute the probe points so that only the appropriate area in MESH_MIN and MESH_MAX is probed. This can dramatically reduce probing times for anything that doesn't fill the first layer of the bed. PRINT_START will automatically use this for bed mesh calibration if a [bed_mesh] section is detected in your config.

The following additional configuration options are available from globals.cfg.

• variable_probe_mesh_padding - Extra padding around the rectangle defined by MESH_MIN and MESH_MAX.
• variable_probe_min_count - Minimum number of probes for partial probing of a bed mesh.
• variable_probe_count_scale - Scaling factor to increase probe count for partial bed probes.

Note: See the optional section for additional macros.

Note: The bed mesh optimizations are silently disabled for delta printers and when the mesh parameters include a RELATIVE_REFERENCE_INDEX (which is icnompatible with dynamic mesh generation).

BED_MESH_CHECK

Checks the [bed_mesh] config and warns if mesh_min or mesh_max could allow a move out of range during BED_MESH_CALIBRATE. This is run implictily at Klipper startup and at the start of BED_MESH_CALIBRATE.

Bed Surface

Provides a set of macros for selecting different bed surfaces with correspdonding Z offset adjustments to compensate for their thickness. All available surfaces must be listed in the variable_bed_surfaces array. Corresponding LCD menus for sheet selection and babystepping will be added to Setup and Tune if lcd_menus.cfg is included. Any Z offset adjustments made in the LCD menus, console, or other clients (e.g. Mainsail, Fluidd) will be applied to the current sheet and persisted across restarts.

SET_SURFACE_ACTIVE

Sets the provided surface active (from one listed in listed in variable_bed_surfaces) and adjusts the current Z offset to match the offset for the surface. If no SURFACE argument is provided the available surfaces are listed, with active surface preceded by a *.

• SURFACE - Bed surface with an associated offset.

SET_SURFACE_OFFSET

Directly sets the the Z offset of SURFACE to the value of OFFSET. If no argument for SURFACE is provided the current active surface is used. If no argument for OFFSET is provided the current offset is displayed.

• OFFSET - New Z offset for the given surface.
• SURFACE (default: current surface) - Bed surface.

Note: The SET_GCODE_OFFSET macro is overridden to update the offset for the active surface. This makes the bed surface work with Z offset adjustments made via any interface or client.

ADJUST_SURFACE_OFFSETS

Adjusts surface offsets to account for changes in the Z endstop position or probe Z offset. A message to invoke this command will be shown in the console when a relevant change is made to printer.cfg.

• IGNORE - Set to 1 to reset the saved offsets without adjusting the surfaces.

Beep

Implements the M300 command (if a corresponding [output_pin beeper] section is present). This command causes the speaker to emit an audible tone.

M300

Emits an audible tone.

• P (default: variable_beep_duration) - Duration of tone.
• S (default: variable_beep_frequency) - Frequency of tone.

Draw

Provides convenience methods for extruding along a path and drawing purge lines.

Note: The drawing macros require every extruder config(s) to have correct nozzle_diameter and filament_diameter settings.

DRAW_LINE_TO

Extrudes a line of filament at the specified height and width from the current coordinate to the supplied XY coordinate (using the currently active extruder).

• X (default: current X position) - Absolute X coordinate to draw to.
• Y (default: current Y position) - Absolute Y coordinate to draw to.
• HEIGHT (default: set via SET_DRAW_PARAMS) - Height (in mm) used to calculate extrusion volume.
• WIDTH (default: set via SET_DRAW_PARAMS) - Extrusion width in mm.
• FEEDRATE (default: set via SET_DRAW_PARAMS) - Drawing feedrate in mm/m.

Note: The Z axis position must be set prior to caling this macro. The HEIGHT parameter is used only to calculate the extrusion volume.

SET_DRAW_PARAMS

Sets the default parameters used by DRAW_LINE_TO. This is helpful in reducing DRAW_LINE_TO command line lengths (particluarly important when debugging in the console).

• HEIGHT (optional; 0.2mm at startup) - Height (in mm) used to calculate extrusion volume.
• WIDTH (optional; nozzle diameter at startup) - Extrusion width in mm.
• FEEDRATE (optional; 1200mm/m at startup) - Drawing feedrate in mm/m.

DRAW_PURGE_LINE

Moves to a position at the front edge of the first print layer and purges the specified length of filament as a line (or rows of lines) in front of the supplied print area. If no print area is specified the purge lines are drawn at the front edge of the maximum printable area. If no printable area is set it defaults to the respective axis limits.

• PRINT_MIN (default: variable_print_min) - Upper boundary of print.
• PRINT_MAX (default: variable_print_max) - Lower boundary of print.
• HEIGHT (default: 62.5% of nozzle diameter) - Extrusion height in mm.
• WIDTH (default: 125% of nozzle diameter) - Extrusion width in mm.
• LENGTH (default: variable_start_purge_length) - Length of filament to purge. The default in variable_start_purge_length is also the amount that is automatically purged at print start.

Note: You must set variable_print_min and variable_print_max if the X and Y axis limits in your config allow your toolhead to move outside the printable area (e.g. for dockable probes or purge buckets).

Note: If your print touches the front edge of the bed it will overlap with with the extrusions from DRAW_PURGE_LINE.

Fans

Implements scaling parameters that alter the behavior of the M106 command. Once set, these parameters apply to any fan speed until they are cleared (by default this happens at the start and end of the print).

SET_FAN_SCALING

Sets scaling parameters for the extruder fan.

• BOOST (default: 0) - Added to the fan speed.
• SCALE (default: 1.0) - The BOOST value is added an then the fan speed is multiplied by SCALE.
• MAXIMUM (default: 255) - The fan speed is clamped to no larger than MAXIMUM.
• MINIMUM (default: 0) - The fan speed is clamped to no less than MINIMUM; if this is a non-zero value the fan can be stopped only via the M107 command.
• SPEED (optional) - This specifies a new speed target, otherwise any new adjustments will be applied to the unadjusted value of the last set fan speed.

RESET_FAN_SCALING

• Clears all existing fan scaling factors.

Filament

LOAD_FILAMENT / UNLOAD_FILAMENT

Loads or unloads filament to the nozzle.

• LENGTH (default: variable_load_length) - The length of filament to load or unload.
• SPEED (default: variable_load_speed) - Speed (in mm/m) to feed the filament.
• MINIMUM (default: min_extrude_temp + 5) - Ensures the extruder is heated to at least the specified temperature.

Marlin Compatibility

• The M701 and M702 commands are implemented with a default filament length of variable_load_length.

Heaters

Adds scaling parameters that can alter the behavior of the specified heater. Once set, these parameters apply to any temperature target on that heater until the scalaing parameters are cleared. A zero target temperature will turn the heater off regardless of scaling parameters.

SET_HEATER_SCALING

Sets scaling parameters for the specified heater. If run without any arguments any currently scaled heaters and thier scaling parameters will be listed. By default the scaling is cleared at the start and end of a print.

• HEATER - The name of the heater to scale.
• BOOST (default: 0.0) - Added to a non-zero target temperature.
• SCALE (default: 1.0) - Multiplied with the boosted target temperature.
• MAXIMUM (default: max_temp) - The target temperature is clamped to no larger than MAXIMUM. This value must be between min_temp and min_temp, inclusive.
• MINIMUM (default: min_temp) - A non-zero target temperature is clamped to no less than MINIMUM. This value must be between min_temp and min_temp, inclusive.
• TARGET (optional) - This specifies a new target temperature, otherwise any new adjustments will be applied to the unadjusted value of the last set target temperature.

Note: a zero target temperature will turn the heater off regardless of scaling parameters.

RESET_HEATER_SCALING

Clears current heater scaling.

• HEATER (optional) - The name of the heater to reset.

Note: if no HEATER argument is specified scaling parameters will be reset for all heaters.

SET_HEATER_TEMPERATURE_SCALED

The scaled version of Klipper's SET_HEATER_TEMPERATURE. All arguments are the same and the function is identical, except that scaling values are applied.

TEMPERATURE_WAIT_SCALED

The scaled version of Klipper's TEMPERATURE_WAIT. All arguments are the same and the function is identical, except that scaling values are applied.

Marlin Compatibility

• The chamber heating commands M141 and M191 are implemented if a corresponding [heater_generic chamber] section is defined in the config.
• The R temperature parameter from Marlin is implemented for the M109 and M190 commands. This parameter will cause a wait until the target temperature stabilizes (i.e. the normal Klipper behavior for S).
• The S parameter for the M109 and M190 commands is altered to behave as it does in Marlin. Rather than causing a wait until the temperature stabilizes, the wait will complete as soon as the temperature target is exceeded.
• The M109, M190, M191, M104, M140, and M141 are all overridden to implement the heater scaling described above.

Note: Both SET_HEATER_TEMPERATURE and TEMPERATURE_WAIT are not overriden and will not scale values. This means that heater scaling adjustments made in clients like Mainsail and Fluidd will not be scaled (because that seemed like the clearest behavior). The custom LCD menus will also replace the temperature controls with non-scaling versions. If you use the stock menus you'll get scaled values.

Kinematics

G28

Extends the G28 command to add lazy homing by not re-homing already homed axes when the O argument is included (equivalent to the same argument in Marlin). See Klipper G28 documentation for general information and detail on the other arguments.

• O - Omits axes from the homing procedure if they are already homed.

Note: If you have a [homing_override] section you will need to update any G28 commands in the gcode part to use G28.6245197 instead (which is the renamed version of Klipper's built-in G28). Failure to do this will cause G28 commands to error out with the message Macro G28 called recursively.

Layer Triggers

Provides the capability to run user-specified g-code commands at arbitrary layer changes.

GCODE_AT_LAYER

Runs abritrary, user-provided g-code commands at the user-specified layer or height. If no arguments are specified it will display all currently scheduled g-code commands along with their associated layer or height.

• HEIGHT - Z height (in mm) to run the command. Exactly one of HEIGHT or LAYER must be specified.
• LAYER - Layer number (zero indexed) to run the command. Exactly one of HEIGHT or LAYER must be specified. The special value next may be specified run the command at the next layer change.
• COMMAND - The command to run at layer change. Take care to properly quote spaces and escape any special characters.
• BEFORE (default: 0) - Set to 1 run the command before the layer change (i.e. immediately following completion of the previous layer). By default commands run after the layer change (i.e. immediately preceding the next layer). In most cases this distinction here doesn't matter, but it can be important when dealing with toolchangers or other multi-material printing.

CANCEL_ALL_LAYER_GCODE

Cancels all g-code commands previously scheduled at any layer or height.

Convenient Layer Change Macros

• PAUSE_NEXT_LAYER ...
  • Schedules the current print to pause at the next layer change. See PAUSE macro for additional arguments.
• PAUSE_AT_LAYER { HEIGHT=<pos> | LAYER=<layer> } ...
  • Schedules the current print to pause at the specified layer change. See PAUSE for additional arguments.
• SPEED_AT_LAYER { HEIGHT=<pos> | LAYER=<layer> } SPEED=<percentage>
  • Schedules a feedrate adjustment at the specified layer change. (SPEED parameter behaves the same as the M220 S parameter.)
• FLOW_AT_LAYER { HEIGHT=<pos> | LAYER=<layer> } FLOW=<percentage>
  • Schedules a flow-rate adjustment at the specified layer change. (FLOW parameter behaves the same as the M221 S parameter.)
• FAN_AT_LAYER { HEIGHT=<pos> | LAYER=<layer> } ...
  • Schedules a fan adjustment at the specified layer change. See SET_FAN_SCALING for additional arguments.
• HEATER_AT_LAYER { HEIGHT=<pos> | LAYER=<layer> } ...
  • Schedules a heater adjustment at the specified layer change. See SET_HEATER_SCALING for additional arguments.

Note: If any triggers cause an exception the current print will abort. The convenience macros above validate their arguments as much as is possible to reduce the chances of an aborted print, but they cannot entirely eliminate the risk of a macro doing something that aborts the print.

Park

Implements toolhead parking.

PARK

Parks the toolhead.

• P (default: 2) - Parking mode
  • P=0 - If current Z-pos is lower than Z-park then the nozzle will be raised to reach Z-park height
  • P=1 - No matter the current Z-pos, the nozzle will be raised/lowered to reach Z-park height.
  • P=2 - The nozzle height will be raised by Z-park amount but never going over the machine’s Z height limit.
• X (default: variable_park_x) - Absolute X parking coordinate.
• Y (default: variable_park_y) - Absolute Y parking coordinate.
• Z (default: variable_park_z) - Z parking coordinate applied according to the P parameter.
• LAZY (default: 1) - Will home any unhomed axes if needed and will not move any axis if already homed and parked (even if P=2).

Note: If a print is in progress the larger of the tallest printed layer or the current Z position will be used as the current Z position, to avoid collisions with already printed objects during a sequential print.

Marlin Compatibility

• The G27 command is implemented with a default P0 argument.

Pause, Resume, Cancel

PAUSE

Pauses the current print.

• X (default: variable_park_x) - Absolute X parking coordinate.
• Y (default: variable_park_y) - Absolute Y parking coordinate.
• Z (default: variable_park_z) - Relative Z parking coordinate
• E (default: 5) - Retraction length to prevent ooze.
• B (default: 10) - Number of beeps to emit (if M300 is enabled).

RESUME

• E (default: 5) - Retraction length to prevent ooze.

CANCEL_PRINT

Cancels the print and performs all the same functions as PRINT_END.

Marlin Compatibility

• The M24, M25, M600, M601, and M602 commands are all implemented by wrapping the above commands.

Print Start and End

PRINT_START

Sets up the printer prior to starting a print (called from the slicer's print start g-code). A target CHAMBER temperature may be provided if a [heater_generic chamber] section is present in the klipper config. If MESH_MIN and MESH_MAX are provided, then BED_MESH_CALIBRATE will probe only the area within the specified rectangle, and will scale the number of probes to the appropriate density (this can dramatically reduce probe times for smaller prints).

• BED - Bed heater starting temperature.
• EXTRUDER - Extruder heater starting temperature.
• CHAMBER (optional) - Chamber heater starting temperature.
• MESH_MIN (optional) - Minimum x,y coordinate of the first layer.
• MESH_MAX (optional) - Maximum x,y coordinate of the first layer.
• NOZZLE_SIZE (default: nozzle_diameter) - Nozzle diameter of the primary extruder.
• LAYERS (optional) - Total number of layers in the print.

PRINT_END

Parks the printhead, shuts down heaters, fans, etc, and performs general state housekeeping at the end of the print (called from the slicer's print end g-code).

Velocity

These are some basic wrappers for Klipper's analogs to some of Marlin's velocity related commands, such as accelleration, jerk, and linear advance.

Marlin Compatibility

• The M201, M203, M204, and M205 commands are implemented by calling Klipper's SET_VELOCITY_LIMIT command. For calls that set the ACCEL parameter, the ACCEL_TO_DECEL parameter is also set and scaled by variable_velocity_decel_scale (default: 0.5).
• The M900 command is implemented by calling Klipper's SET_PRESSURE_ADVANCE command. The K factor is scaled by variable_pressure_advance_scale (default: -1.0). If the scaling value is negative the M900 command has no effect.

Optional Configs

Bed Mesh

BED_MESH_CALIBRATE and G20

Overrides the default BED_MESH_CALIBRATE to use BED_MESH_CALIBRATE_FAST instead, and adds the G20 command.

Configuration:

[include klipper-macros/optional/bed_mesh.cfg]

Requirements: A properly configured bed_mesh section.

LCD Menus

Adds relevant menu items to an LCD display and improves some existing functionality. See the customization section above for more information on how to configure specific behaviors.

• Confirmation added for cancelling the print or disabling steppers during a print.
• Several temperature menu changes:
  • Up to 10 filaments and their corresponding temperatures can be set via variable_menu_temperature.
  • Per filament chamber temperature controls are available if a [heater_generic chamber] section is configured.
  • The cooldown commands are moved to the top level temperature menu.
• The filament loading commands are replaced with macros that use the lengths and speeds specified in variable_load_length and variable_load_speed, which includes a priming phase at the end of the load (controlled via variable_load_priming_length and variable_load_priming_speed).
• Bed surface management is integrated into the setup and tuning menus.
• The SD card menu has been streamlined for printing and non-printing modes.
• The setup menu includes host shutdown, host restart, speed, and flow controls.
• You can hide the Octoprint or SD card menus if you don't use them (via variable_menu_show_octoprint and variable_menu_show_sdcard, respectively).

Configuration:

[include klipper-macros/optional/lcd_menus.cfg]

Requirements: A properly configured display section.