ofproto-unixctl.man

.SS "OFPROTO COMMANDS"
These commands manage the core OpenFlow switch implementation (called
\fBofproto\fR).
.
.IP "\fBofproto/list\fR"
Lists the names of the running ofproto instances.  These are the names
that may be used on \fBofproto/trace\fR.
.
.IP "\fBofproto/trace\fR [\fIdpname\fR] \fIodp_flow\fR [\fB\-generate \fR| \fIpacket\fR]"
.IQ "\fBofproto/trace\fR \fIbridge\fR \fIbr_flow\fR [\fB\-generate \fR| \fIpacket\fR]"
.IQ "\fBofproto/trace\-packet\-out\fR [\fB\-consistent\fR] [\fIdpname\fR] \fIodp_flow\fR [\fB\-generate \fR| \fIpacket\fR] \fIactions\fR"
.IQ "\fBofproto/trace\-packet\-out\fR [\fB\-consistent\fR] \fIbridge\fR \fIbr_flow\fR [\fB\-generate \fR| \fIpacket\fR] \fIactions\fR"
Traces the path of an imaginary packet through \fIswitch\fR and
reports the path that it took.  The initial treatment of the packet
varies based on the command:
.
.RS
.IP \(bu
\fBofproto/trace\fR looks the packet up in the OpenFlow flow table, as
if the packet had arrived on an OpenFlow port.
.
.IP \(bu
\fBofproto/trace\-packet\-out\fR applies the specified OpenFlow
\fIactions\fR, as if the packet, flow, and actions had been specified
in an OpenFlow ``packet-out'' request.
.RE
.
.IP
The packet's headers (e.g. source and destination) and metadata
(e.g. input port), together called its ``flow,'' are usually all that
matter for the purpose of tracing a packet.  You can specify the flow
in the following ways:
.
.RS
.IP "\fIdpname\fR \fIodp_flow\fR"
\fIodp_flow\fR is a flow in the form printed by \fBovs\-dpctl\fR(8)'s
\fBdump\-flows\fR command.  If all of your bridges have the same type,
which is the common case, then you can omit \fIdpname\fR, but if you
have bridges of different types (say, both \fBovs-netdev\fR and
\fBovs-system\fR), then you need to specify a \fIdpname\fR to disambiguate.
.
.IP "\fIbridge\fR \fIbr_flow\fR"
\fIbr_flow\fR is a flow in the form similar to that accepted by
\fBovs\-ofctl\fR(8)'s \fBadd\-flow\fR command.  (This is not an
OpenFlow flow: besides other differences, it never contains
wildcards.)  \fIbridge\fR names of the bridge through which
\fIbr_flow\fR should be traced.
.RE
.
.IP
Most commonly, one specifies only a flow, using one of the forms
above, but sometimes one might need to specify an actual packet
instead of just a flow:
.
.RS
.IP "Side effects."
Some actions have side effects.  For example, the \fBnormal\fR action
can update the MAC learning table, and the \fBlearn\fR action can
change OpenFlow tables.  The trace commands only perform side
effects when a packet is specified.  If you want side effects to take
place, then you must supply a packet.
.
.IP
(Output actions are obviously side effects too, but
the trace commands never execute them, even when one specifies a
packet.)
.
.IP "Incomplete information."
Most of the time, Open vSwitch can figure out everything about the
path of a packet using just the flow, but in some special
circumstances it needs to look at parts of the packet that are not
included in the flow.  When this is the case, and you do not supply a
packet, then a trace command will tell you it needs a packet.
.RE
.
.IP
If you wish to include a packet as part of a trace operation, there
are two ways to do it:
.
.RS
.IP \fB\-generate\fR
This option, added to one of the ways to specify a flow already
described, causes Open vSwitch to internally generate a packet with
the flow described and then to use that packet.  If your goal is to
execute side effects, then \fB\-generate\fR is the easiest way to do
it, but \fB\-generate\fR is not a good way to fill in incomplete
information, because it generates packets based on only the flow
information, which means that the packets really do not have any more
information than the flow.
.
.IP \fIpacket\fR
This form supplies an explicit \fIpacket\fR as a sequence of hex
digits.  An Ethernet frame is at least 14 bytes long, so there must be
at least 28 hex digits.  Obviously, it is inconvenient to type in the
hex digits by hand, so the \fBovs\-pcap\fR(1) and
\fBovs\-tcpundump\fR(1) utilities provide easier ways.
.IP
With this form, packet headers are extracted directly from
\fIpacket\fR, so the \fIodp_flow\fR or \fIbr_flow\fR should specify
only metadata. The metadata can be:
.RS
.IP \fIskb_priority\fR
Packet QoS priority.
.IP \fIpkt_mark\fR
Mark of the packet.
.IP \fItun_id\fR
The tunnel ID on which the packet arrived.
.IP \fIin_port\fR
The port on which the packet arrived.
.RE
.RE
.
.IP
The in_port value is kernel datapath port number for the first format
and OpenFlow port number for the second format. The numbering of these
two types of port usually differs and there is no relationship.
.
.IP
\fBofproto\-trace\-packet\-out\fR accepts an additional
\fB\-consistent\fR option.  With this option specified, the command
rejects \fIactions\fR that are inconsistent with the specified packet.
(An example of an inconsistency is attempting to strip the VLAN tag
from a packet that does not have a VLAN tag.)  Open vSwitch ignores
most forms of inconsistency in OpenFlow 1.0 and rejects
inconsistencies in later versions of OpenFlow.  The option is
necessary because the command does not ordinarily imply a particular
OpenFlow version.  One exception is that, when \fIactions\fR includes
an action that only OpenFlow 1.1 and later supports (such as
\fBpush_vlan\fR), \fB\-consistent\fR is automatically enabled.
.IP "\fBofproto/self\-check\fR [\fIswitch\fR]"
Runs an internal consistency check on \fIswitch\fR, if specified,
otherwise on all ofproto instances, and responds with a brief summary
of the results.  If the summary reports any errors, then the Open
vSwitch logs should contain more detailed information.  Please pass
along errors reported by this command to the Open vSwitch developers
as bugs.