diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 95e93eb28893..fa1b470ab2d0 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -1478,6 +1478,15 @@
// Enable if SD detect is rendered useless (e.g., by using an SD extender)
//#define NO_SD_DETECT
+ // Multiple volume support - EXPERIMENTAL.
+ //#define MULTI_VOLUME
+ #if ENABLED(MULTI_VOLUME)
+ #define VOLUME_SD_ONBOARD
+ #define VOLUME_USB_FLASH_DRIVE
+ #define DEFAULT_VOLUME SD_ONBOARD
+ #define DEFAULT_SHARED_VOLUME USB_FLASH_DRIVE
+ #endif
+
#endif // SDSUPPORT
/**
diff --git a/Marlin/src/HAL/DUE/usb/sd_mmc_spi_mem.cpp b/Marlin/src/HAL/DUE/usb/sd_mmc_spi_mem.cpp
index d92d332c1efd..3dcbbaecd28f 100644
--- a/Marlin/src/HAL/DUE/usb/sd_mmc_spi_mem.cpp
+++ b/Marlin/src/HAL/DUE/usb/sd_mmc_spi_mem.cpp
@@ -32,7 +32,7 @@ Ctrl_status sd_mmc_spi_test_unit_ready() {
Ctrl_status sd_mmc_spi_read_capacity(uint32_t *nb_sector) {
if (!IS_SD_INSERTED() || IS_SD_PRINTING() || IS_SD_FILE_OPEN() || !card.isMounted())
return CTRL_NO_PRESENT;
- *nb_sector = card.getSd2Card().cardSize() - 1;
+ *nb_sector = card.diskIODriver()->cardSize() - 1;
return CTRL_GOOD;
}
@@ -74,24 +74,24 @@ Ctrl_status sd_mmc_spi_usb_read_10(uint32_t addr, uint16_t nb_sector) {
#endif
// Start reading
- if (!card.getSd2Card().readStart(addr))
+ if (!card.diskIODriver()->readStart(addr))
return CTRL_FAIL;
// For each specified sector
while (nb_sector--) {
// Read a sector
- card.getSd2Card().readData(sector_buf);
+ card.diskIODriver()->readData(sector_buf);
// RAM -> USB
if (!udi_msc_trans_block(true, sector_buf, SD_MMC_BLOCK_SIZE, nullptr)) {
- card.getSd2Card().readStop();
+ card.diskIODriver()->readStop();
return CTRL_FAIL;
}
}
// Stop reading
- card.getSd2Card().readStop();
+ card.diskIODriver()->readStop();
// Done
return CTRL_GOOD;
@@ -113,7 +113,7 @@ Ctrl_status sd_mmc_spi_usb_write_10(uint32_t addr, uint16_t nb_sector) {
}
#endif
- if (!card.getSd2Card().writeStart(addr, nb_sector))
+ if (!card.diskIODriver()->writeStart(addr, nb_sector))
return CTRL_FAIL;
// For each specified sector
@@ -121,16 +121,16 @@ Ctrl_status sd_mmc_spi_usb_write_10(uint32_t addr, uint16_t nb_sector) {
// USB -> RAM
if (!udi_msc_trans_block(false, sector_buf, SD_MMC_BLOCK_SIZE, nullptr)) {
- card.getSd2Card().writeStop();
+ card.diskIODriver()->writeStop();
return CTRL_FAIL;
}
// Write a sector
- card.getSd2Card().writeData(sector_buf);
+ card.diskIODriver()->writeData(sector_buf);
}
// Stop writing
- card.getSd2Card().writeStop();
+ card.diskIODriver()->writeStop();
// Done
return CTRL_GOOD;
diff --git a/Marlin/src/HAL/STM32/msc_sd.cpp b/Marlin/src/HAL/STM32/msc_sd.cpp
index 63ce7808f183..20e1ab3cf96c 100644
--- a/Marlin/src/HAL/STM32/msc_sd.cpp
+++ b/Marlin/src/HAL/STM32/msc_sd.cpp
@@ -30,54 +30,66 @@
class Sd2CardUSBMscHandler : public USBMscHandler {
public:
+ DiskIODriver* diskIODriver() {
+ #if ENABLED(MULTI_VOLUME)
+ #if SHARED_VOLUME_IS(SD_ONBOARD)
+ return &card.media_sd_spi;
+ #elif SHARED_VOLUME_IS(USB_FLASH_DRIVE)
+ return &card.media_usbFlashDrive;
+ #endif
+ #else
+ return diskIODriver();
+ #endif
+ }
+
bool GetCapacity(uint32_t *pBlockNum, uint16_t *pBlockSize) {
- *pBlockNum = card.getSd2Card().cardSize();
+ *pBlockNum = diskIODriver()->cardSize();
*pBlockSize = BLOCK_SIZE;
return true;
}
bool Write(uint8_t *pBuf, uint32_t blkAddr, uint16_t blkLen) {
- auto sd2card = card.getSd2Card();
+ auto sd2card = diskIODriver();
// single block
if (blkLen == 1) {
watchdog_refresh();
- sd2card.writeBlock(blkAddr, pBuf);
+ sd2card->writeBlock(blkAddr, pBuf);
return true;
}
// multi block optmization
- sd2card.writeStart(blkAddr, blkLen);
+ sd2card->writeStart(blkAddr, blkLen);
while (blkLen--) {
watchdog_refresh();
- sd2card.writeData(pBuf);
+ sd2card->writeData(pBuf);
pBuf += BLOCK_SIZE;
}
- sd2card.writeStop();
+ sd2card->writeStop();
return true;
}
bool Read(uint8_t *pBuf, uint32_t blkAddr, uint16_t blkLen) {
- auto sd2card = card.getSd2Card();
+ auto sd2card = diskIODriver();
// single block
if (blkLen == 1) {
watchdog_refresh();
- sd2card.readBlock(blkAddr, pBuf);
+ sd2card->readBlock(blkAddr, pBuf);
return true;
}
// multi block optmization
- sd2card.readStart(blkAddr);
+ sd2card->readStart(blkAddr);
while (blkLen--) {
watchdog_refresh();
- sd2card.readData(pBuf);
+ sd2card->readData(pBuf);
pBuf += BLOCK_SIZE;
}
- sd2card.readStop();
+ sd2card->readStop();
return true;
}
bool IsReady() {
- return card.isMounted();
+ return diskIODriver()->isReady();
}
};
@@ -105,8 +117,8 @@ USBMscHandler *pSingleMscHandler = &usbMscHandler;
void MSC_SD_init() {
USBDevice.end();
delay(200);
- USBDevice.begin();
USBDevice.registerMscHandlers(1, &pSingleMscHandler, Marlin_STORAGE_Inquirydata);
+ USBDevice.begin();
}
#endif // __STM32F1__ && HAS_SD_HOST_DRIVE
diff --git a/Marlin/src/MarlinCore.cpp b/Marlin/src/MarlinCore.cpp
index 738f9a8d7894..842429a40737 100644
--- a/Marlin/src/MarlinCore.cpp
+++ b/Marlin/src/MarlinCore.cpp
@@ -757,7 +757,7 @@ void idle(TERN_(ADVANCED_PAUSE_FEATURE, bool no_stepper_sleep/*=false*/)) {
TERN_(SDSUPPORT, card.manage_media());
// Handle USB Flash Drive insert / remove
- TERN_(USB_FLASH_DRIVE_SUPPORT, Sd2Card::idle());
+ TERN_(USB_FLASH_DRIVE_SUPPORT, card.diskIODriver()->idle());
// Announce Host Keepalive state (if any)
TERN_(HOST_KEEPALIVE_FEATURE, gcode.host_keepalive());
diff --git a/Marlin/src/inc/Conditionals_adv.h b/Marlin/src/inc/Conditionals_adv.h
index 3bd77d754597..735e6464d93f 100644
--- a/Marlin/src/inc/Conditionals_adv.h
+++ b/Marlin/src/inc/Conditionals_adv.h
@@ -245,7 +245,7 @@
#define _CUTTER_POWER_PERCENT 2
#define _CUTTER_POWER_RPM 3
#define _CUTTER_POWER(V) _CAT(_CUTTER_POWER_, V)
- #define CUTTER_UNIT_IS(V) (_CUTTER_POWER(CUTTER_POWER_UNIT) == _CUTTER_POWER(V))
+ #define CUTTER_UNIT_IS(V) (_CUTTER_POWER(CUTTER_POWER_UNIT) == _CUTTER_POWER(V))
#endif
// Add features that need hardware PWM here
diff --git a/Marlin/src/inc/Conditionals_post.h b/Marlin/src/inc/Conditionals_post.h
index 337cf2a950e4..f00dd6ec97ad 100644
--- a/Marlin/src/inc/Conditionals_post.h
+++ b/Marlin/src/inc/Conditionals_post.h
@@ -356,6 +356,15 @@
#define SD_DETECT_STATE LOW
#endif
#endif
+
+ #if DISABLED(USB_FLASH_DRIVE_SUPPORT) || BOTH(MULTI_VOLUME, VOLUME_SD_ONBOARD)
+ #if ENABLED(SDIO_SUPPORT)
+ #define NEED_SD2CARD_SDIO 1
+ #else
+ #define NEED_SD2CARD_SPI 1
+ #endif
+ #endif
+
#endif
#if ANY(HAS_GRAPHICAL_TFT, LCD_USE_DMA_FSMC, HAS_FSMC_GRAPHICAL_TFT, HAS_SPI_GRAPHICAL_TFT) || !PIN_EXISTS(SD_DETECT)
diff --git a/Marlin/src/lcd/extui/lib/mks_ui/draw_keyboard.cpp b/Marlin/src/lcd/extui/lib/mks_ui/draw_keyboard.cpp
index a05c558beb7a..3572991813a0 100644
--- a/Marlin/src/lcd/extui/lib/mks_ui/draw_keyboard.cpp
+++ b/Marlin/src/lcd/extui/lib/mks_ui/draw_keyboard.cpp
@@ -148,7 +148,7 @@ static void lv_kb_event_cb(lv_obj_t *kb, lv_event_t event) {
public_buf_l[6] = 0x00;
raw_send_to_wifi((uint8_t*)public_buf_l, 6);
- last_disp_state = KEY_BOARD_UI;
+ last_disp_state = KEYBOARD_UI;
lv_clear_keyboard();
wifi_tips_type = TIPS_TYPE_JOINING;
lv_draw_wifi_tips();
@@ -216,7 +216,7 @@ static void lv_kb_event_cb(lv_obj_t *kb, lv_event_t event) {
}
void lv_draw_keyboard() {
- scr = lv_screen_create(KEY_BOARD_UI, "");
+ scr = lv_screen_create(KEYBOARD_UI, "");
// Create styles for the keyboard
static lv_style_t rel_style, pr_style;
diff --git a/Marlin/src/lcd/extui/lib/mks_ui/draw_media_select.cpp b/Marlin/src/lcd/extui/lib/mks_ui/draw_media_select.cpp
new file mode 100644
index 000000000000..6dc816cc234e
--- /dev/null
+++ b/Marlin/src/lcd/extui/lib/mks_ui/draw_media_select.cpp
@@ -0,0 +1,73 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see .
+ *
+ */
+#include "../../../../inc/MarlinConfigPre.h"
+
+#if BOTH(HAS_TFT_LVGL_UI, MULTI_VOLUME)
+
+#include "draw_ui.h"
+#include
+
+#include "../../../../inc/MarlinConfig.h"
+#include "../../../../sd/cardreader.h"
+
+extern lv_group_t *g;
+static lv_obj_t *scr;
+
+enum {
+ ID_T_USB_DISK = 1,
+ ID_T_SD_DISK,
+ ID_T_RETURN
+};
+
+#if ENABLED(MKS_TEST)
+ extern uint8_t curent_disp_ui;
+#endif
+
+static void event_handler(lv_obj_t *obj, lv_event_t event) {
+ if (event != LV_EVENT_RELEASED) return;
+ lv_clear_media_select();
+ switch (obj->mks_obj_id) {
+ case ID_T_USB_DISK: card.changeMedia(&card.media_usbFlashDrive); break;
+ case ID_T_SD_DISK: card.changeMedia(&card.media_sd_spi); break;
+ case ID_T_RETURN:
+ TERN_(MKS_TEST, curent_disp_ui = 1);
+ lv_draw_ready_print();
+ return;
+ }
+ lv_draw_print_file();
+}
+
+void lv_draw_media_select() {
+ scr = lv_screen_create(MEDIA_SELECT_UI);
+ lv_big_button_create(scr, "F:/bmp_sd.bin", media_select_menu.sd_disk, INTERVAL_V, titleHeight, event_handler, ID_T_SD_DISK);
+ lv_big_button_create(scr, "F:/bmp_usb_disk.bin", media_select_menu.usb_disk, BTN_X_PIXEL + INTERVAL_V * 2, titleHeight, event_handler, ID_T_USB_DISK);
+ lv_big_button_create(scr, "F:/bmp_return.bin", common_menu.text_back, BTN_X_PIXEL * 3 + INTERVAL_V * 4, BTN_Y_PIXEL + INTERVAL_H + titleHeight, event_handler, ID_T_RETURN);
+}
+
+void lv_clear_media_select() {
+ #if HAS_ROTARY_ENCODER
+ if (gCfgItems.encoder_enable) lv_group_remove_all_objs(g);
+ #endif
+ lv_obj_del(scr);
+}
+
+#endif // HAS_TFT_LVGL_UI
diff --git a/Marlin/src/lcd/extui/lib/mks_ui/draw_media_select.h b/Marlin/src/lcd/extui/lib/mks_ui/draw_media_select.h
new file mode 100644
index 000000000000..a698714a9dce
--- /dev/null
+++ b/Marlin/src/lcd/extui/lib/mks_ui/draw_media_select.h
@@ -0,0 +1,33 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see .
+ *
+ */
+#pragma once
+
+#ifdef __cplusplus
+ extern "C" { /* C-declarations for C++ */
+#endif
+
+extern void lv_draw_media_select();
+extern void lv_clear_media_select();
+
+#ifdef __cplusplus
+ } /* C-declarations for C++ */
+#endif
diff --git a/Marlin/src/lcd/extui/lib/mks_ui/draw_print_file.cpp b/Marlin/src/lcd/extui/lib/mks_ui/draw_print_file.cpp
index d32851f76167..17f5d95d2ae0 100644
--- a/Marlin/src/lcd/extui/lib/mks_ui/draw_print_file.cpp
+++ b/Marlin/src/lcd/extui/lib/mks_ui/draw_print_file.cpp
@@ -177,7 +177,7 @@ static void event_handler(lv_obj_t *obj, lv_event_t event) {
}
else {
lv_clear_print_file();
- lv_draw_ready_print();
+ TERN(MULTI_VOLUME, lv_draw_media_select(), lv_draw_ready_print());
}
}
else {
@@ -248,6 +248,7 @@ static char test_public_buf_l[40];
void disp_gcode_icon(uint8_t file_num) {
uint8_t i;
+ // TODO: set current media title?!
scr = lv_screen_create(PRINT_FILE_UI, "");
// Create image buttons
diff --git a/Marlin/src/lcd/extui/lib/mks_ui/draw_ready_print.cpp b/Marlin/src/lcd/extui/lib/mks_ui/draw_ready_print.cpp
index d02e774b94cb..09784b51845b 100644
--- a/Marlin/src/lcd/extui/lib/mks_ui/draw_ready_print.cpp
+++ b/Marlin/src/lcd/extui/lib/mks_ui/draw_ready_print.cpp
@@ -73,7 +73,7 @@ static void event_handler(lv_obj_t *obj, lv_event_t event) {
case ID_INFO_EXT: uiCfg.curTempType = 0; lv_draw_preHeat(); break;
case ID_INFO_BED: uiCfg.curTempType = 1; lv_draw_preHeat(); break;
case ID_INFO_FAN: lv_draw_fan(); break;
- case ID_PRINT: lv_draw_print_file(); break;
+ case ID_PRINT: TERN(MULTI_VOLUME, lv_draw_media_select(), lv_draw_print_file()); break;
}
}
diff --git a/Marlin/src/lcd/extui/lib/mks_ui/draw_ui.cpp b/Marlin/src/lcd/extui/lib/mks_ui/draw_ui.cpp
index 51e187435c04..0a99df08e5a4 100644
--- a/Marlin/src/lcd/extui/lib/mks_ui/draw_ui.cpp
+++ b/Marlin/src/lcd/extui/lib/mks_ui/draw_ui.cpp
@@ -447,111 +447,63 @@ char *getDispText(int index) {
ZERO(public_buf_l);
switch (disp_state_stack._disp_state[index]) {
- case PRINT_READY_UI:
- strcpy(public_buf_l, main_menu.title);
- break;
- case PRINT_FILE_UI:
- strcpy(public_buf_l, file_menu.title);
- break;
+ case PRINT_READY_UI: strcpy(public_buf_l, main_menu.title); break;
+ case PRINT_FILE_UI: strcpy(public_buf_l, file_menu.title); break;
case PRINTING_UI:
- if (disp_state_stack._disp_state[disp_state_stack._disp_index] == PRINTING_UI
- #ifndef TFT35
- || disp_state_stack._disp_state[disp_state_stack._disp_index] == OPERATE_UI
- || disp_state_stack._disp_state[disp_state_stack._disp_index] == PAUSE_UI
- #endif
- ) strcpy(public_buf_l, common_menu.print_special_title);
- else strcpy(public_buf_l, printing_menu.title);
- break;
- case MOVE_MOTOR_UI:
- strcpy(public_buf_l, move_menu.title);
+ switch (disp_state_stack._disp_state[disp_state_stack._disp_index]) {
+ IF_DISABLED(TFT35, case OPERATE_UI: case PAUSE_UI:)
+ case PRINTING_UI: strcpy(public_buf_l, common_menu.print_special_title); break;
+ default: strcpy(public_buf_l, printing_menu.title); break;
+ }
break;
+ case MOVE_MOTOR_UI: strcpy(public_buf_l, move_menu.title); break;
case OPERATE_UI:
- if (disp_state_stack._disp_state[disp_state_stack._disp_index] == PRINTING_UI
- #ifndef TFT35
- || disp_state_stack._disp_state[disp_state_stack._disp_index] == OPERATE_UI
- || disp_state_stack._disp_state[disp_state_stack._disp_index] == PAUSE_UI
- #endif
- ) strcpy(public_buf_l, common_menu.operate_special_title);
- else strcpy(public_buf_l, operation_menu.title);
+ switch (disp_state_stack._disp_state[disp_state_stack._disp_index]) {
+ IF_DISABLED(TFT35, case OPERATE_UI: case PAUSE_UI:)
+ case PRINTING_UI: strcpy(public_buf_l, common_menu.operate_special_title); break;
+ default: strcpy(public_buf_l, operation_menu.title); break;
+ }
break;
case PAUSE_UI:
- if (disp_state_stack._disp_state[disp_state_stack._disp_index] == PRINTING_UI
- || disp_state_stack._disp_state[disp_state_stack._disp_index] == OPERATE_UI
- || disp_state_stack._disp_state[disp_state_stack._disp_index] == PAUSE_UI
- ) strcpy(public_buf_l, common_menu.pause_special_title);
- else strcpy(public_buf_l, pause_menu.title);
- break;
-
- case EXTRUSION_UI:
- strcpy(public_buf_l, extrude_menu.title);
- break;
- case CHANGE_SPEED_UI:
- strcpy(public_buf_l, speed_menu.title);
- break;
- case FAN_UI:
- strcpy(public_buf_l, fan_menu.title);
+ switch (disp_state_stack._disp_state[disp_state_stack._disp_index]) {
+ case OPERATE_UI:
+ case PAUSE_UI:
+ case PRINTING_UI: strcpy(public_buf_l, common_menu.pause_special_title); break;
+ default: strcpy(public_buf_l, pause_menu.title); break;
+ }
break;
+ case EXTRUSION_UI: strcpy(public_buf_l, extrude_menu.title); break;
+ case CHANGE_SPEED_UI: strcpy(public_buf_l, speed_menu.title); break;
+ case FAN_UI: strcpy(public_buf_l, fan_menu.title); break;
case PRE_HEAT_UI:
- if ((disp_state_stack._disp_state[disp_state_stack._disp_index - 1] == OPERATE_UI))
- strcpy(public_buf_l, preheat_menu.adjust_title);
- else strcpy(public_buf_l, preheat_menu.title);
- break;
- case SET_UI:
- strcpy(public_buf_l, set_menu.title);
- break;
- case ZERO_UI:
- strcpy(public_buf_l, home_menu.title);
- break;
- case SPRAYER_UI: break;
- case MACHINE_UI: break;
- case LANGUAGE_UI:
- strcpy(public_buf_l, language_menu.title);
- break;
- case ABOUT_UI:
- strcpy(public_buf_l, about_menu.title);
- break;
- case LOG_UI: break;
- case DISK_UI:
- strcpy(public_buf_l, filesys_menu.title);
- break;
- case DIALOG_UI:
- strcpy(public_buf_l, common_menu.dialog_confirm_title);
- break;
- case WIFI_UI:
- strcpy(public_buf_l, wifi_menu.title);
+ switch (disp_state_stack._disp_state[disp_state_stack._disp_index]) {
+ case OPERATE_UI: strcpy(public_buf_l, preheat_menu.adjust_title);
+ default: strcpy(public_buf_l, preheat_menu.title); break;
+ }
break;
+ case SET_UI: strcpy(public_buf_l, set_menu.title); break;
+ case ZERO_UI: strcpy(public_buf_l, home_menu.title); break;
+ case SPRAYER_UI: break;
+ case MACHINE_UI: break;
+ case LANGUAGE_UI: strcpy(public_buf_l, language_menu.title); break;
+ case ABOUT_UI: strcpy(public_buf_l, about_menu.title); break;
+ case LOG_UI: break;
+ case DISK_UI: strcpy(public_buf_l, filesys_menu.title); break;
+ case DIALOG_UI: strcpy(public_buf_l, common_menu.dialog_confirm_title); break;
+ case WIFI_UI: strcpy(public_buf_l, wifi_menu.title); break;
case MORE_UI:
- case PRINT_MORE_UI:
- strcpy(public_buf_l, more_menu.title);
- break;
- case FILAMENTCHANGE_UI:
- strcpy(public_buf_l, filament_menu.title);
- break;
+ case PRINT_MORE_UI: strcpy(public_buf_l, more_menu.title); break;
+ case FILAMENTCHANGE_UI: strcpy(public_buf_l, filament_menu.title); break;
case LEVELING_UI:
- case MESHLEVELING_UI:
- strcpy(public_buf_l, leveling_menu.title);
- break;
- case BIND_UI:
- strcpy(public_buf_l, cloud_menu.title);
- break;
- case TOOL_UI:
- strcpy(public_buf_l, tool_menu.title);
- break;
- case WIFI_LIST_UI:
- #if ENABLED(MKS_WIFI_MODULE)
- strcpy(public_buf_l, list_menu.title);
- break;
- #endif
- case MACHINE_PARA_UI:
- strcpy(public_buf_l, MachinePara_menu.title);
- break;
- case BABY_STEP_UI:
- strcpy(public_buf_l, operation_menu.babystep);
- break;
- case EEPROM_SETTINGS_UI:
- strcpy(public_buf_l, eeprom_menu.title);
- break;
+ case MESHLEVELING_UI: strcpy(public_buf_l, leveling_menu.title); break;
+ case BIND_UI: strcpy(public_buf_l, cloud_menu.title); break;
+ case TOOL_UI: strcpy(public_buf_l, tool_menu.title); break;
+ case WIFI_LIST_UI: TERN_(MKS_WIFI_MODULE, strcpy(public_buf_l, list_menu.title)); break;
+ case MACHINE_PARA_UI: strcpy(public_buf_l, MachinePara_menu.title); break;
+ case BABY_STEP_UI: strcpy(public_buf_l, operation_menu.babystep); break;
+ case EEPROM_SETTINGS_UI: strcpy(public_buf_l, eeprom_menu.title); break;
+ case MEDIA_SELECT_UI: strcpy(public_buf_l, media_select_menu.title); break;
default: break;
}
@@ -828,11 +780,9 @@ void GUI_RefreshPage() {
}
break;
- case OPERATE_UI:
- break;
+ case OPERATE_UI: break;
- case PAUSE_UI:
- break;
+ case PAUSE_UI: break;
case FAN_UI:
if (temps_update_flag) {
@@ -841,8 +791,7 @@ void GUI_RefreshPage() {
}
break;
- case MOVE_MOTOR_UI:
- break;
+ case MOVE_MOTOR_UI: break;
#if ENABLED(MKS_WIFI_MODULE)
case WIFI_UI:
@@ -852,10 +801,9 @@ void GUI_RefreshPage() {
}
break;
- case BIND_UI:
- refresh_bind_ui();
- break;
+ case BIND_UI: refresh_bind_ui(); break;
#endif
+
case FILAMENTCHANGE_UI:
if (temps_update_flag) {
temps_update_flag = false;
@@ -866,10 +814,8 @@ void GUI_RefreshPage() {
filament_dialog_handle();
TERN_(MKS_WIFI_MODULE, wifi_scan_handle());
break;
- case MESHLEVELING_UI:
- break;
- case HARDWARE_TEST_UI:
- break;
+ case MESHLEVELING_UI: break;
+ case HARDWARE_TEST_UI: break;
case WIFI_LIST_UI:
#if ENABLED(MKS_WIFI_MODULE)
if (printing_rate_update_flag) {
@@ -878,8 +824,8 @@ void GUI_RefreshPage() {
}
#endif
break;
- case KEY_BOARD_UI:
- break;
+ case KEYBOARD_UI: break;
+
#if ENABLED(MKS_WIFI_MODULE)
case WIFI_TIPS_UI:
switch (wifi_tips_type) {
@@ -932,6 +878,7 @@ void GUI_RefreshPage() {
disp_z_offset_value();
}
break;
+
default: break;
}
@@ -982,7 +929,7 @@ void clear_cur_ui() {
#if ENABLED(MKS_WIFI_MODULE)
case WIFI_LIST_UI: lv_clear_wifi_list(); break;
#endif
- case KEY_BOARD_UI: lv_clear_keyboard(); break;
+ case KEYBOARD_UI: lv_clear_keyboard(); break;
#if ENABLED(MKS_WIFI_MODULE)
case WIFI_TIPS_UI: lv_clear_wifi_tips(); break;
#endif
@@ -1013,9 +960,9 @@ void clear_cur_ui() {
case NUMBER_KEY_UI: lv_clear_number_key(); break;
case BABY_STEP_UI: lv_clear_baby_stepping(); break;
case PAUSE_POS_UI: lv_clear_pause_position(); break;
- #if HAS_TRINAMIC_CONFIG
- case TMC_CURRENT_UI: lv_clear_tmc_current_settings(); break;
- #endif
+ #if HAS_TRINAMIC_CONFIG
+ case TMC_CURRENT_UI: lv_clear_tmc_current_settings(); break;
+ #endif
case EEPROM_SETTINGS_UI: lv_clear_eeprom_settings(); break;
#if HAS_STEALTHCHOP
case TMC_MODE_UI: lv_clear_tmc_step_mode_settings(); break;
@@ -1032,6 +979,9 @@ void clear_cur_ui() {
#if ENABLED(TOUCH_SCREEN_CALIBRATION)
case TOUCH_CALIBRATION_UI: lv_clear_touch_calibration_screen(); break;
#endif
+ #if ENABLED(MULTI_VOLUME)
+ case MEDIA_SELECT_UI: lv_clear_media_select(); break;
+ #endif
default: break;
}
}
@@ -1087,7 +1037,7 @@ void draw_return_ui() {
#if ENABLED(MKS_WIFI_MODULE)
case WIFI_LIST_UI: lv_draw_wifi_list(); break;
#endif
- case KEY_BOARD_UI: lv_draw_keyboard(); break;
+ case KEYBOARD_UI: lv_draw_keyboard(); break;
#if ENABLED(MKS_WIFI_MODULE)
case WIFI_TIPS_UI: lv_draw_wifi_tips(); break;
#endif
diff --git a/Marlin/src/lcd/extui/lib/mks_ui/draw_ui.h b/Marlin/src/lcd/extui/lib/mks_ui/draw_ui.h
index 6577d80cdf0c..2809e4e93791 100644
--- a/Marlin/src/lcd/extui/lib/mks_ui/draw_ui.h
+++ b/Marlin/src/lcd/extui/lib/mks_ui/draw_ui.h
@@ -76,6 +76,7 @@
#include "draw_homing_sensitivity_settings.h"
#include "draw_baby_stepping.h"
#include "draw_keyboard.h"
+#include "draw_media_select.h"
#include "draw_encoder_settings.h"
#include "../../../../inc/MarlinConfigPre.h"
@@ -289,7 +290,7 @@ typedef enum {
TOOL_UI,
HARDWARE_TEST_UI,
WIFI_LIST_UI,
- KEY_BOARD_UI,
+ KEYBOARD_UI,
WIFI_TIPS_UI,
MACHINE_PARA_UI,
MACHINE_SETTINGS_UI,
@@ -327,6 +328,7 @@ typedef enum {
ENCODER_SETTINGS_UI,
TOUCH_CALIBRATION_UI,
GCODE_UI,
+ MEDIA_SELECT_UI,
} DISP_STATE;
typedef struct {
diff --git a/Marlin/src/lcd/extui/lib/mks_ui/pic_manager.cpp b/Marlin/src/lcd/extui/lib/mks_ui/pic_manager.cpp
index 36f276c21b28..9318b50d2bca 100644
--- a/Marlin/src/lcd/extui/lib/mks_ui/pic_manager.cpp
+++ b/Marlin/src/lcd/extui/lib/mks_ui/pic_manager.cpp
@@ -197,6 +197,13 @@ static const char assets[][LONG_FILENAME_LENGTH] = {
"bmp_cloud.bin",
#endif
+ #if ENABLED(MULTI_VOLUME)
+ "bmp_usb_disk.bin",
+ // "bmp_usb_disk_sel.bin",
+ "bmp_sd.bin",
+ // "bmp_sd_sel.bin",
+ #endif
+
// Babystep screen
"bmp_baby_move0_01.bin",
"bmp_baby_move0_05.bin",
diff --git a/Marlin/src/lcd/extui/lib/mks_ui/tft_Language_en.h b/Marlin/src/lcd/extui/lib/mks_ui/tft_Language_en.h
index 104e1fdcafd6..b6eef183682a 100644
--- a/Marlin/src/lcd/extui/lib/mks_ui/tft_Language_en.h
+++ b/Marlin/src/lcd/extui/lib/mks_ui/tft_Language_en.h
@@ -540,6 +540,7 @@
#define USB_DRIVE_BACK_EN "< Back"
#define FILE_PAGES_EN "%d/%d"
#define FILE_NEXT_PAGE_EN "Next Page"
+#define MEDIA_SELECT_TITLE_EN "Select Media"
//BUILD PLATE
#define PLATE_TITLE_EN "Build Plate"
diff --git a/Marlin/src/lcd/extui/lib/mks_ui/tft_multi_language.cpp b/Marlin/src/lcd/extui/lib/mks_ui/tft_multi_language.cpp
index 20b7d5f60603..5e37acb2b4d8 100644
--- a/Marlin/src/lcd/extui/lib/mks_ui/tft_multi_language.cpp
+++ b/Marlin/src/lcd/extui/lib/mks_ui/tft_multi_language.cpp
@@ -56,6 +56,7 @@ tool_menu_def tool_menu;
MachinePara_menu_def MachinePara_menu;
pause_msg_def pause_msg_menu;
eeprom_def eeprom_menu;
+media_select_menu_def media_select_menu;
machine_common_def machine_menu;
void machine_setting_disp() {
@@ -821,6 +822,10 @@ void disp_language_init() {
filament_menu.stat_temp = TEXT_VALUE;
+ media_select_menu.title = MEDIA_SELECT_TITLE_EN;
+ media_select_menu.sd_disk = SD_CARD_TITLE_EN;
+ media_select_menu.usb_disk = USB_DRIVE_TITLE_EN;
+
machine_menu.key_0 = KEYBOARD_KEY0_EN;
machine_menu.key_1 = KEYBOARD_KEY1_EN;
machine_menu.key_2 = KEYBOARD_KEY2_EN;
diff --git a/Marlin/src/lcd/extui/lib/mks_ui/tft_multi_language.h b/Marlin/src/lcd/extui/lib/mks_ui/tft_multi_language.h
index 61e3524c5838..79faad74e208 100644
--- a/Marlin/src/lcd/extui/lib/mks_ui/tft_multi_language.h
+++ b/Marlin/src/lcd/extui/lib/mks_ui/tft_multi_language.h
@@ -706,6 +706,14 @@ typedef struct tool_menu_disp {
extern tool_menu_def tool_menu;
+typedef struct media_select_menu_disp {
+ const char *title;
+ const char *sd_disk;
+ const char *usb_disk;
+} media_select_menu_def;
+
+extern media_select_menu_def media_select_menu;
+
typedef struct MachinePara_menu_disp {
const char *title;
const char *MachineSetting;
diff --git a/Marlin/src/lcd/extui/lib/mks_ui/wifi_module.cpp b/Marlin/src/lcd/extui/lib/mks_ui/wifi_module.cpp
index 6c2afeafd3dc..1162f7a228ed 100644
--- a/Marlin/src/lcd/extui/lib/mks_ui/wifi_module.cpp
+++ b/Marlin/src/lcd/extui/lib/mks_ui/wifi_module.cpp
@@ -1142,7 +1142,7 @@ static void wifi_list_msg_handle(uint8_t * msg, uint16_t msgLen) {
int8_t valid_name_num;
if (msgLen <= 0) return;
- if (disp_state == KEY_BOARD_UI) return;
+ if (disp_state == KEYBOARD_UI) return;
wifi_list.getNameNum = msg[0];
diff --git a/Marlin/src/sd/Sd2Card.cpp b/Marlin/src/sd/Sd2Card.cpp
index 28049c7e7e39..3e714fe9fefe 100644
--- a/Marlin/src/sd/Sd2Card.cpp
+++ b/Marlin/src/sd/Sd2Card.cpp
@@ -30,7 +30,7 @@
#include "../inc/MarlinConfig.h"
-#if ENABLED(SDSUPPORT) && NONE(USB_FLASH_DRIVE_SUPPORT, SDIO_SUPPORT)
+#if NEED_SD2CARD_SPI
/* Enable FAST CRC computations - You can trade speed for FLASH space if
* needed by disabling the following define */
@@ -88,7 +88,7 @@
#endif
// Send command and return error code. Return zero for OK
-uint8_t Sd2Card::cardCommand(const uint8_t cmd, const uint32_t arg) {
+uint8_t DiskIODriver_SPI_SD::cardCommand(const uint8_t cmd, const uint32_t arg) {
// Select card
chipSelect();
@@ -133,7 +133,7 @@ uint8_t Sd2Card::cardCommand(const uint8_t cmd, const uint32_t arg) {
* \return The number of 512 byte data blocks in the card
* or zero if an error occurs.
*/
-uint32_t Sd2Card::cardSize() {
+uint32_t DiskIODriver_SPI_SD::cardSize() {
csd_t csd;
if (!readCSD(&csd)) return 0;
if (csd.v1.csd_ver == 0) {
@@ -155,12 +155,12 @@ uint32_t Sd2Card::cardSize() {
}
}
-void Sd2Card::chipDeselect() {
+void DiskIODriver_SPI_SD::chipDeselect() {
extDigitalWrite(chipSelectPin_, HIGH);
spiSend(0xFF); // Ensure MISO goes high impedance
}
-void Sd2Card::chipSelect() {
+void DiskIODriver_SPI_SD::chipSelect() {
spiInit(spiRate_);
extDigitalWrite(chipSelectPin_, LOW);
}
@@ -178,7 +178,7 @@ void Sd2Card::chipSelect() {
*
* \return true for success, false for failure.
*/
-bool Sd2Card::erase(uint32_t firstBlock, uint32_t lastBlock) {
+bool DiskIODriver_SPI_SD::erase(uint32_t firstBlock, uint32_t lastBlock) {
if (ENABLED(SDCARD_READONLY)) return false;
csd_t csd;
@@ -216,7 +216,7 @@ bool Sd2Card::erase(uint32_t firstBlock, uint32_t lastBlock) {
* \return true if single block erase is supported.
* false if single block erase is not supported.
*/
-bool Sd2Card::eraseSingleBlockEnable() {
+bool DiskIODriver_SPI_SD::eraseSingleBlockEnable() {
csd_t csd;
return readCSD(&csd) ? csd.v1.erase_blk_en : false;
}
@@ -230,7 +230,7 @@ bool Sd2Card::eraseSingleBlockEnable() {
* \return true for success, false for failure.
* The reason for failure can be determined by calling errorCode() and errorData().
*/
-bool Sd2Card::init(const uint8_t sckRateID, const pin_t chipSelectPin) {
+bool DiskIODriver_SPI_SD::init(const uint8_t sckRateID, const pin_t chipSelectPin) {
#if IS_TEENSY_35_36 || IS_TEENSY_40_41
chipSelectPin_ = BUILTIN_SDCARD;
const uint8_t ret = SDHC_CardInit();
@@ -324,10 +324,12 @@ bool Sd2Card::init(const uint8_t sckRateID, const pin_t chipSelectPin) {
}
chipDeselect();
+ ready = true;
return setSckRate(sckRateID);
FAIL:
chipDeselect();
+ ready = false;
return false;
}
@@ -338,7 +340,7 @@ bool Sd2Card::init(const uint8_t sckRateID, const pin_t chipSelectPin) {
* \param[out] dst Pointer to the location that will receive the data.
* \return true for success, false for failure.
*/
-bool Sd2Card::readBlock(uint32_t blockNumber, uint8_t *dst) {
+bool DiskIODriver_SPI_SD::readBlock(uint32_t blockNumber, uint8_t *dst) {
#if IS_TEENSY_35_36 || IS_TEENSY_40_41
return 0 == SDHC_CardReadBlock(dst, blockNumber);
#endif
@@ -378,7 +380,7 @@ bool Sd2Card::readBlock(uint32_t blockNumber, uint8_t *dst) {
*
* \return true for success, false for failure.
*/
-bool Sd2Card::readData(uint8_t *dst) {
+bool DiskIODriver_SPI_SD::readData(uint8_t *dst) {
chipSelect();
return readData(dst, 512);
}
@@ -445,7 +447,7 @@ bool Sd2Card::readData(uint8_t *dst) {
#endif
#endif // SD_CHECK_AND_RETRY
-bool Sd2Card::readData(uint8_t *dst, const uint16_t count) {
+bool DiskIODriver_SPI_SD::readData(uint8_t *dst, const uint16_t count) {
bool success = false;
const millis_t read_timeout = millis() + SD_READ_TIMEOUT;
@@ -477,7 +479,7 @@ bool Sd2Card::readData(uint8_t *dst, const uint16_t count) {
}
/** read CID or CSR register */
-bool Sd2Card::readRegister(const uint8_t cmd, void *buf) {
+bool DiskIODriver_SPI_SD::readRegister(const uint8_t cmd, void *buf) {
uint8_t *dst = reinterpret_cast(buf);
if (cardCommand(cmd, 0)) {
error(SD_CARD_ERROR_READ_REG);
@@ -497,7 +499,7 @@ bool Sd2Card::readRegister(const uint8_t cmd, void *buf) {
*
* \return true for success, false for failure.
*/
-bool Sd2Card::readStart(uint32_t blockNumber) {
+bool DiskIODriver_SPI_SD::readStart(uint32_t blockNumber) {
if (type() != SD_CARD_TYPE_SDHC) blockNumber <<= 9;
const bool success = !cardCommand(CMD18, blockNumber);
@@ -511,7 +513,7 @@ bool Sd2Card::readStart(uint32_t blockNumber) {
*
* \return true for success, false for failure.
*/
-bool Sd2Card::readStop() {
+bool DiskIODriver_SPI_SD::readStop() {
chipSelect();
const bool success = !cardCommand(CMD12, 0);
if (!success) error(SD_CARD_ERROR_CMD12);
@@ -531,7 +533,7 @@ bool Sd2Card::readStop() {
* \return The value one, true, is returned for success and the value zero,
* false, is returned for an invalid value of \a sckRateID.
*/
-bool Sd2Card::setSckRate(const uint8_t sckRateID) {
+bool DiskIODriver_SPI_SD::setSckRate(const uint8_t sckRateID) {
const bool success = (sckRateID <= 6);
if (success) spiRate_ = sckRateID; else error(SD_CARD_ERROR_SCK_RATE);
return success;
@@ -542,12 +544,14 @@ bool Sd2Card::setSckRate(const uint8_t sckRateID) {
* \param[in] timeout_ms Timeout to abort.
* \return true for success, false for timeout.
*/
-bool Sd2Card::waitNotBusy(const millis_t timeout_ms) {
+bool DiskIODriver_SPI_SD::waitNotBusy(const millis_t timeout_ms) {
const millis_t wait_timeout = millis() + timeout_ms;
while (spiRec() != 0xFF) if (ELAPSED(millis(), wait_timeout)) return false;
return true;
}
+void DiskIODriver_SPI_SD::error(const uint8_t code) { errorCode_ = code; }
+
/**
* Write a 512 byte block to an SD card.
*
@@ -555,7 +559,7 @@ bool Sd2Card::waitNotBusy(const millis_t timeout_ms) {
* \param[in] src Pointer to the location of the data to be written.
* \return true for success, false for failure.
*/
-bool Sd2Card::writeBlock(uint32_t blockNumber, const uint8_t *src) {
+bool DiskIODriver_SPI_SD::writeBlock(uint32_t blockNumber, const uint8_t *src) {
if (ENABLED(SDCARD_READONLY)) return false;
#if IS_TEENSY_35_36 || IS_TEENSY_40_41
@@ -586,7 +590,7 @@ bool Sd2Card::writeBlock(uint32_t blockNumber, const uint8_t *src) {
* \param[in] src Pointer to the location of the data to be written.
* \return true for success, false for failure.
*/
-bool Sd2Card::writeData(const uint8_t *src) {
+bool DiskIODriver_SPI_SD::writeData(const uint8_t *src) {
if (ENABLED(SDCARD_READONLY)) return false;
bool success = true;
@@ -601,7 +605,7 @@ bool Sd2Card::writeData(const uint8_t *src) {
}
// Send one block of data for write block or write multiple blocks
-bool Sd2Card::writeData(const uint8_t token, const uint8_t *src) {
+bool DiskIODriver_SPI_SD::writeData(const uint8_t token, const uint8_t *src) {
if (ENABLED(SDCARD_READONLY)) return false;
const uint16_t crc = TERN(SD_CHECK_AND_RETRY, CRC_CCITT(src, 512), 0xFFFF);
@@ -629,7 +633,7 @@ bool Sd2Card::writeData(const uint8_t token, const uint8_t *src) {
*
* \return true for success, false for failure.
*/
-bool Sd2Card::writeStart(uint32_t blockNumber, const uint32_t eraseCount) {
+bool DiskIODriver_SPI_SD::writeStart(uint32_t blockNumber, const uint32_t eraseCount) {
if (ENABLED(SDCARD_READONLY)) return false;
bool success = false;
@@ -650,7 +654,7 @@ bool Sd2Card::writeStart(uint32_t blockNumber, const uint32_t eraseCount) {
*
* \return true for success, false for failure.
*/
-bool Sd2Card::writeStop() {
+bool DiskIODriver_SPI_SD::writeStop() {
if (ENABLED(SDCARD_READONLY)) return false;
bool success = false;
@@ -666,4 +670,4 @@ bool Sd2Card::writeStop() {
return success;
}
-#endif // SDSUPPORT
+#endif // NEED_SD2CARD_SPI
diff --git a/Marlin/src/sd/Sd2Card.h b/Marlin/src/sd/Sd2Card.h
index eb7f9bb2cac1..e0dce02a0236 100644
--- a/Marlin/src/sd/Sd2Card.h
+++ b/Marlin/src/sd/Sd2Card.h
@@ -35,47 +35,50 @@
#include "SdFatConfig.h"
#include "SdInfo.h"
+#include "disk_io_driver.h"
#include
-uint16_t const SD_INIT_TIMEOUT = 2000, // init timeout ms
- SD_ERASE_TIMEOUT = 10000, // erase timeout ms
- SD_READ_TIMEOUT = 300, // read timeout ms
- SD_WRITE_TIMEOUT = 600; // write time out ms
+uint16_t const SD_INIT_TIMEOUT = 2000, // (ms) Init timeout
+ SD_ERASE_TIMEOUT = 10000, // (ms) Erase timeout
+ SD_READ_TIMEOUT = 300, // (ms) Read timeout
+ SD_WRITE_TIMEOUT = 600; // (ms) Write timeout
// SD card errors
-uint8_t const SD_CARD_ERROR_CMD0 = 0x01, // timeout error for command CMD0 (initialize card in SPI mode)
- SD_CARD_ERROR_CMD8 = 0x02, // CMD8 was not accepted - not a valid SD card
- SD_CARD_ERROR_CMD12 = 0x03, // card returned an error response for CMD12 (write stop)
- SD_CARD_ERROR_CMD17 = 0x04, // card returned an error response for CMD17 (read block)
- SD_CARD_ERROR_CMD18 = 0x05, // card returned an error response for CMD18 (read multiple block)
- SD_CARD_ERROR_CMD24 = 0x06, // card returned an error response for CMD24 (write block)
- SD_CARD_ERROR_CMD25 = 0x07, // WRITE_MULTIPLE_BLOCKS command failed
- SD_CARD_ERROR_CMD58 = 0x08, // card returned an error response for CMD58 (read OCR)
- SD_CARD_ERROR_ACMD23 = 0x09, // SET_WR_BLK_ERASE_COUNT failed
- SD_CARD_ERROR_ACMD41 = 0x0A, // ACMD41 initialization process timeout
- SD_CARD_ERROR_BAD_CSD = 0x0B, // card returned a bad CSR version field
- SD_CARD_ERROR_ERASE = 0x0C, // erase block group command failed
- SD_CARD_ERROR_ERASE_SINGLE_BLOCK = 0x0D, // card not capable of single block erase
- SD_CARD_ERROR_ERASE_TIMEOUT = 0x0E, // Erase sequence timed out
- SD_CARD_ERROR_READ = 0x0F, // card returned an error token instead of read data
- SD_CARD_ERROR_READ_REG = 0x10, // read CID or CSD failed
- SD_CARD_ERROR_READ_TIMEOUT = 0x11, // timeout while waiting for start of read data
- SD_CARD_ERROR_STOP_TRAN = 0x12, // card did not accept STOP_TRAN_TOKEN
- SD_CARD_ERROR_WRITE = 0x13, // card returned an error token as a response to a write operation
- SD_CARD_ERROR_WRITE_BLOCK_ZERO = 0x14, // REMOVE - not used ... attempt to write protected block zero
- SD_CARD_ERROR_WRITE_MULTIPLE = 0x15, // card did not go ready for a multiple block write
- SD_CARD_ERROR_WRITE_PROGRAMMING = 0x16, // card returned an error to a CMD13 status check after a write
- SD_CARD_ERROR_WRITE_TIMEOUT = 0x17, // timeout occurred during write programming
- SD_CARD_ERROR_SCK_RATE = 0x18, // incorrect rate selected
- SD_CARD_ERROR_INIT_NOT_CALLED = 0x19, // init() not called
- // 0x1A is unused now, it was: card returned an error for CMD59 (CRC_ON_OFF)
- SD_CARD_ERROR_READ_CRC = 0x1B; // invalid read CRC
+typedef enum : uint8_t {
+ SD_CARD_ERROR_CMD0 = 0x01, // Timeout error for command CMD0 (initialize card in SPI mode)
+ SD_CARD_ERROR_CMD8 = 0x02, // CMD8 was not accepted - not a valid SD card
+ SD_CARD_ERROR_CMD12 = 0x03, // Card returned an error response for CMD12 (write stop)
+ SD_CARD_ERROR_CMD17 = 0x04, // Card returned an error response for CMD17 (read block)
+ SD_CARD_ERROR_CMD18 = 0x05, // Card returned an error response for CMD18 (read multiple block)
+ SD_CARD_ERROR_CMD24 = 0x06, // Card returned an error response for CMD24 (write block)
+ SD_CARD_ERROR_CMD25 = 0x07, // WRITE_MULTIPLE_BLOCKS command failed
+ SD_CARD_ERROR_CMD58 = 0x08, // Card returned an error response for CMD58 (read OCR)
+ SD_CARD_ERROR_ACMD23 = 0x09, // SET_WR_BLK_ERASE_COUNT failed
+ SD_CARD_ERROR_ACMD41 = 0x0A, // ACMD41 initialization process timeout
+ SD_CARD_ERROR_BAD_CSD = 0x0B, // Card returned a bad CSR version field
+ SD_CARD_ERROR_ERASE = 0x0C, // Erase block group command failed
+ SD_CARD_ERROR_ERASE_SINGLE_BLOCK = 0x0D, // Card not capable of single block erase
+ SD_CARD_ERROR_ERASE_TIMEOUT = 0x0E, // Erase sequence timed out
+ SD_CARD_ERROR_READ = 0x0F, // Card returned an error token instead of read data
+ SD_CARD_ERROR_READ_REG = 0x10, // Read CID or CSD failed
+ SD_CARD_ERROR_READ_TIMEOUT = 0x11, // Timeout while waiting for start of read data
+ SD_CARD_ERROR_STOP_TRAN = 0x12, // Card did not accept STOP_TRAN_TOKEN
+ SD_CARD_ERROR_WRITE = 0x13, // Card returned an error token as a response to a write operation
+ SD_CARD_ERROR_WRITE_BLOCK_ZERO = 0x14, // REMOVE - not used ... attempt to write protected block zero
+ SD_CARD_ERROR_WRITE_MULTIPLE = 0x15, // Card did not go ready for a multiple block write
+ SD_CARD_ERROR_WRITE_PROGRAMMING = 0x16, // Card returned an error to a CMD13 status check after a write
+ SD_CARD_ERROR_WRITE_TIMEOUT = 0x17, // Timeout occurred during write programming
+ SD_CARD_ERROR_SCK_RATE = 0x18, // Incorrect rate selected
+ SD_CARD_ERROR_INIT_NOT_CALLED = 0x19, // Init() not called
+ // 0x1A is unused now, it was: card returned an error for CMD59 (CRC_ON_OFF)
+ SD_CARD_ERROR_READ_CRC = 0x1B // Invalid read CRC
+} sd_error_code_t;
// card types
-uint8_t const SD_CARD_TYPE_SD1 = 1, // Standard capacity V1 SD card
- SD_CARD_TYPE_SD2 = 2, // Standard capacity V2 SD card
- SD_CARD_TYPE_SDHC = 3; // High Capacity SD card
+uint8_t const SD_CARD_TYPE_SD1 = 1, // Standard capacity V1 SD card
+ SD_CARD_TYPE_SD2 = 2, // Standard capacity V2 SD card
+ SD_CARD_TYPE_SDHC = 3; // High Capacity SD card
/**
* Define SOFTWARE_SPI to use bit-bang SPI
@@ -93,12 +96,11 @@ uint8_t const SD_CARD_TYPE_SD1 = 1, // Standard capacity V1
* \class Sd2Card
* \brief Raw access to SD and SDHC flash memory cards.
*/
-class Sd2Card {
+class DiskIODriver_SPI_SD : public DiskIODriver {
public:
- Sd2Card() : errorCode_(SD_CARD_ERROR_INIT_NOT_CALLED), type_(0) {}
+ DiskIODriver_SPI_SD() : errorCode_(SD_CARD_ERROR_INIT_NOT_CALLED), type_(0) {}
- uint32_t cardSize();
bool erase(uint32_t firstBlock, uint32_t lastBlock);
bool eraseSingleBlockEnable();
@@ -106,7 +108,7 @@ class Sd2Card {
* Set SD error code.
* \param[in] code value for error code.
*/
- inline void error(const uint8_t code) { errorCode_ = code; }
+ void error(const uint8_t code);
/**
* \return error code for last error. See Sd2Card.h for a list of error codes.
@@ -122,9 +124,15 @@ class Sd2Card {
*
* \return true for success or false for failure.
*/
- bool init(const uint8_t sckRateID, const pin_t chipSelectPin);
+ bool init(const uint8_t sckRateID, const pin_t chipSelectPin) override;
- bool readBlock(uint32_t block, uint8_t *dst);
+ bool setSckRate(const uint8_t sckRateID);
+
+ /**
+ * Return the card type: SD V1, SD V2 or SDHC
+ * \return 0 - SD V1, 1 - SD V2, or 3 - SDHC.
+ */
+ int type() const { return type_; }
/**
* Read a card's CID register. The CID contains card identification
@@ -145,24 +153,27 @@ class Sd2Card {
*
* \return true for success or false for failure.
*/
- inline bool readCSD(csd_t *csd) { return readRegister(CMD9, csd); }
+ inline bool readCSD(csd_t *csd) override { return readRegister(CMD9, csd); }
- bool readData(uint8_t *dst);
- bool readStart(uint32_t blockNumber);
- bool readStop();
- bool setSckRate(const uint8_t sckRateID);
+ bool readData(uint8_t *dst) override;
+ bool readStart(uint32_t blockNumber) override;
+ bool readStop() override;
- /**
- * Return the card type: SD V1, SD V2 or SDHC
- * \return 0 - SD V1, 1 - SD V2, or 3 - SDHC.
- */
- int type() const {return type_;}
- bool writeBlock(uint32_t blockNumber, const uint8_t *src);
- bool writeData(const uint8_t *src);
- bool writeStart(uint32_t blockNumber, const uint32_t eraseCount);
- bool writeStop();
+ bool writeData(const uint8_t *src) override;
+ bool writeStart(const uint32_t blockNumber, const uint32_t eraseCount) override;
+ bool writeStop() override;
+
+ bool readBlock(uint32_t block, uint8_t *dst) override;
+ bool writeBlock(uint32_t blockNumber, const uint8_t *src) override;
+
+ uint32_t cardSize() override;
+
+ bool isReady() override { return ready; };
+
+ void idle() override {}
private:
+ bool ready = false;
uint8_t chipSelectPin_,
errorCode_,
spiRate_,
diff --git a/Marlin/src/sd/Sd2Card_sdio.h b/Marlin/src/sd/Sd2Card_sdio.h
index 10fb757359f4..158034480597 100644
--- a/Marlin/src/sd/Sd2Card_sdio.h
+++ b/Marlin/src/sd/Sd2Card_sdio.h
@@ -23,17 +23,33 @@
#include "../inc/MarlinConfig.h"
-#if ENABLED(SDIO_SUPPORT)
+#include "SdInfo.h"
+#include "disk_io_driver.h"
bool SDIO_Init();
bool SDIO_ReadBlock(uint32_t block, uint8_t *dst);
bool SDIO_WriteBlock(uint32_t block, const uint8_t *src);
-class Sd2Card {
+class DiskIODriver_SDIO : public DiskIODriver {
public:
- bool init(uint8_t sckRateID = 0, uint8_t chipSelectPin = 0) { return SDIO_Init(); }
- bool readBlock(uint32_t block, uint8_t *dst) { return SDIO_ReadBlock(block, dst); }
- bool writeBlock(uint32_t block, const uint8_t *src) { return SDIO_WriteBlock(block, src); }
-};
+ bool init(const uint8_t sckRateID=0, const pin_t chipSelectPin=0) override { return SDIO_Init(); }
+
+ bool readCSD(csd_t *csd) override { return false; }
+
+ bool readStart(const uint32_t block) override { return false; }
+ bool readData(uint8_t *dst) override { return false; }
+ bool readStop() override { return false; }
+
+ bool writeStart(const uint32_t block, const uint32_t) override { return false; }
+ bool writeData(const uint8_t *src) override { return false; }
+ bool writeStop() override { return false; }
-#endif // SDIO_SUPPORT
+ bool readBlock(uint32_t block, uint8_t *dst) override { return SDIO_ReadBlock(block, dst); }
+ bool writeBlock(uint32_t block, const uint8_t *src) override { return SDIO_WriteBlock(block, src); }
+
+ uint32_t cardSize() override { return 0; }
+
+ bool isReady() override { return true; }
+
+ void idle() override {}
+};
diff --git a/Marlin/src/sd/SdFatConfig.h b/Marlin/src/sd/SdFatConfig.h
index 13ac3a748785..dfba64129526 100644
--- a/Marlin/src/sd/SdFatConfig.h
+++ b/Marlin/src/sd/SdFatConfig.h
@@ -39,7 +39,7 @@
*
* Each card requires about 550 bytes of SRAM so use of a Mega is recommended.
*/
-#define USE_MULTIPLE_CARDS 0
+#define USE_MULTIPLE_CARDS 0 //TODO? ENABLED(MULTI_VOLUME)
/**
* Call flush for endl if ENDL_CALLS_FLUSH is nonzero
diff --git a/Marlin/src/sd/SdVolume.cpp b/Marlin/src/sd/SdVolume.cpp
index 7fcebd640d24..1b1fdc5a7c1e 100644
--- a/Marlin/src/sd/SdVolume.cpp
+++ b/Marlin/src/sd/SdVolume.cpp
@@ -41,10 +41,10 @@
// raw block cache
uint32_t SdVolume::cacheBlockNumber_; // current block number
cache_t SdVolume::cacheBuffer_; // 512 byte cache for Sd2Card
- Sd2Card* SdVolume::sdCard_; // pointer to SD card object
+ DiskIODriver *SdVolume::sdCard_; // pointer to SD card object
bool SdVolume::cacheDirty_; // cacheFlush() will write block if true
uint32_t SdVolume::cacheMirrorBlock_; // mirror block for second FAT
-#endif // USE_MULTIPLE_CARDS
+#endif
// find a contiguous group of clusters
bool SdVolume::allocContiguous(uint32_t count, uint32_t *curCluster) {
@@ -326,7 +326,7 @@ int32_t SdVolume::freeClusterCount() {
* Reasons for failure include not finding a valid partition, not finding a valid
* FAT file system in the specified partition or an I/O error.
*/
-bool SdVolume::init(Sd2Card* dev, uint8_t part) {
+bool SdVolume::init(DiskIODriver* dev, uint8_t part) {
uint32_t totalBlocks, volumeStartBlock = 0;
fat32_boot_t *fbs;
diff --git a/Marlin/src/sd/SdVolume.h b/Marlin/src/sd/SdVolume.h
index c2eaf0bd1387..b8e70ca9d7f5 100644
--- a/Marlin/src/sd/SdVolume.h
+++ b/Marlin/src/sd/SdVolume.h
@@ -36,9 +36,11 @@
#if ENABLED(USB_FLASH_DRIVE_SUPPORT)
#include "usb_flashdrive/Sd2Card_FlashDrive.h"
-#elif ENABLED(SDIO_SUPPORT)
+#endif
+
+#if NEED_SD2CARD_SDIO
#include "Sd2Card_sdio.h"
-#else
+#elif NEED_SD2CARD_SPI
#include "Sd2Card.h"
#endif
@@ -47,6 +49,7 @@
//==============================================================================
// SdVolume class
+
/**
* \brief Cache for an SD data block
*/
@@ -84,14 +87,14 @@ class SdVolume {
* Initialize a FAT volume. Try partition one first then try super
* floppy format.
*
- * \param[in] dev The Sd2Card where the volume is located.
+ * \param[in] dev The DiskIODriver where the volume is located.
*
* \return true for success, false for failure.
* Reasons for failure include not finding a valid partition, not finding
* a valid FAT file system or an I/O error.
*/
- bool init(Sd2Card *dev) { return init(dev, 1) ? true : init(dev, 0); }
- bool init(Sd2Card *dev, uint8_t part);
+ bool init(DiskIODriver *dev) { return init(dev, 1) || init(dev, 0); }
+ bool init(DiskIODriver *dev, uint8_t part);
// inline functions that return volume info
uint8_t blocksPerCluster() const { return blocksPerCluster_; } //> \return The volume's cluster size in blocks.
@@ -112,10 +115,10 @@ class SdVolume {
uint32_t rootDirStart() const { return rootDirStart_; }
/**
- * Sd2Card object for this volume
- * \return pointer to Sd2Card object.
+ * DiskIODriver object for this volume
+ * \return pointer to DiskIODriver object.
*/
- Sd2Card* sdCard() { return sdCard_; }
+ DiskIODriver* sdCard() { return sdCard_; }
/**
* Debug access to FAT table
@@ -138,13 +141,13 @@ class SdVolume {
#if USE_MULTIPLE_CARDS
cache_t cacheBuffer_; // 512 byte cache for device blocks
uint32_t cacheBlockNumber_; // Logical number of block in the cache
- Sd2Card *sdCard_; // Sd2Card object for cache
+ DiskIODriver *sdCard_; // DiskIODriver object for cache
bool cacheDirty_; // cacheFlush() will write block if true
uint32_t cacheMirrorBlock_; // block number for mirror FAT
#else
static cache_t cacheBuffer_; // 512 byte cache for device blocks
static uint32_t cacheBlockNumber_; // Logical number of block in the cache
- static Sd2Card *sdCard_; // Sd2Card object for cache
+ static DiskIODriver *sdCard_; // DiskIODriver object for cache
static bool cacheDirty_; // cacheFlush() will write block if true
static uint32_t cacheMirrorBlock_; // block number for mirror FAT
#endif
diff --git a/Marlin/src/sd/cardreader.cpp b/Marlin/src/sd/cardreader.cpp
index 07a57cc6586f..a54884bec127 100644
--- a/Marlin/src/sd/cardreader.cpp
+++ b/Marlin/src/sd/cardreader.cpp
@@ -120,7 +120,16 @@ uint8_t CardReader::workDirDepth;
#endif // SDCARD_SORT_ALPHA
-Sd2Card CardReader::sd2card;
+#if SHARED_VOLUME_IS(USB_FLASH_DRIVE) || ENABLED(USB_FLASH_DRIVE_SUPPORT)
+ DiskIODriver_USBFlash CardReader::media_usbFlashDrive;
+#endif
+#if NEED_SD2CARD_SDIO
+ DiskIODriver_SDIO CardReader::media_sdio;
+#elif NEED_SD2CARD_SPI
+ DiskIODriver_SPI_SD CardReader::media_sd_spi;
+#endif
+
+DiskIODriver* CardReader::driver = nullptr;
SdVolume CardReader::volume;
SdFile CardReader::file;
@@ -133,6 +142,16 @@ SdFile CardReader::file;
uint32_t CardReader::filesize, CardReader::sdpos;
CardReader::CardReader() {
+ changeMedia(&
+ #if SHARED_VOLUME_IS(SD_ONBOARD)
+ media_sd_spi
+ #elif SHARED_VOLUME_IS(USB_FLASH_DRIVE) || ENABLED(USB_FLASH_DRIVE_SUPPORT)
+ media_usbFlashDrive
+ #else
+ TERN(SDIO_SUPPORT, media_sdio, media_sd_spi)
+ #endif
+ );
+
#if ENABLED(SDCARD_SORT_ALPHA)
sort_count = 0;
#if ENABLED(SDSORT_GCODE)
@@ -383,12 +402,12 @@ void CardReader::mount() {
flag.mounted = false;
if (root.isOpen()) root.close();
- if (!sd2card.init(SD_SPI_SPEED, SDSS)
+ if (!driver->init(SD_SPI_SPEED, SDSS)
#if defined(LCD_SDSS) && (LCD_SDSS != SDSS)
- && !sd2card.init(SD_SPI_SPEED, LCD_SDSS)
+ && !driver->init(SD_SPI_SPEED, LCD_SDSS)
#endif
) SERIAL_ECHO_MSG(STR_SD_INIT_FAIL);
- else if (!volume.init(&sd2card))
+ else if (!volume.init(driver))
SERIAL_ERROR_MSG(STR_SD_VOL_INIT_FAIL);
else if (!root.openRoot(&volume))
SERIAL_ERROR_MSG(STR_SD_OPENROOT_FAIL);
diff --git a/Marlin/src/sd/cardreader.h b/Marlin/src/sd/cardreader.h
index f1002e1dab3b..5fdd1222aea4 100644
--- a/Marlin/src/sd/cardreader.h
+++ b/Marlin/src/sd/cardreader.h
@@ -42,6 +42,29 @@ extern const char M23_STR[], M24_STR[];
#define MAXPATHNAMELENGTH (1 + (MAXDIRNAMELENGTH + 1) * (MAX_DIR_DEPTH) + 1 + FILENAME_LENGTH) // "/" + N * ("ADIRNAME/") + "filename.ext"
#include "SdFile.h"
+#include "disk_io_driver.h"
+
+#if ENABLED(USB_FLASH_DRIVE_SUPPORT)
+ #include "usb_flashdrive/Sd2Card_FlashDrive.h"
+#endif
+
+#if NEED_SD2CARD_SDIO
+ #include "Sd2Card_sdio.h"
+#elif NEED_SD2CARD_SPI
+ #include "Sd2Card.h"
+#endif
+
+#if ENABLED(MULTI_VOLUME)
+ #define SV_SD_ONBOARD 1
+ #define SV_USB_FLASH_DRIVE 2
+ #define _VOLUME_ID(N) _CAT(SV_, N)
+ #define SHARED_VOLUME_IS(N) (DEFAULT_SHARED_VOLUME == _VOLUME_ID(N))
+ #if !SHARED_VOLUME_IS(SD_ONBOARD) && !SHARED_VOLUME_IS(USB_FLASH_DRIVE)
+ #error "DEFAULT_SHARED_VOLUME must be either SD_ONBOARD or USB_FLASH_DRIVE."
+ #endif
+#else
+ #define SHARED_VOLUME_IS(...) 0
+#endif
typedef struct {
bool saving:1,
@@ -80,6 +103,8 @@ class CardReader {
CardReader();
+ static void changeMedia(DiskIODriver *_driver) { driver = _driver; }
+
static SdFile getroot() { return root; }
static void mount();
@@ -171,7 +196,8 @@ class CardReader {
static inline int16_t read(void *buf, uint16_t nbyte) { return file.isOpen() ? file.read(buf, nbyte) : -1; }
static inline int16_t write(void *buf, uint16_t nbyte) { return file.isOpen() ? file.write(buf, nbyte) : -1; }
- static Sd2Card& getSd2Card() { return sd2card; }
+ // TODO: rename to diskIODriver()
+ static DiskIODriver* diskIODriver() { return driver; }
#if ENABLED(AUTO_REPORT_SD_STATUS)
//
@@ -181,6 +207,15 @@ class CardReader {
static AutoReporter auto_reporter;
#endif
+ #if SHARED_VOLUME_IS(USB_FLASH_DRIVE) || ENABLED(USB_FLASH_DRIVE_SUPPORT)
+ static DiskIODriver_USBFlash media_usbFlashDrive;
+ #endif
+ #if NEED_SD2CARD_SDIO
+ static DiskIODriver_SDIO media_sdio;
+ #elif NEED_SD2CARD_SPI
+ static DiskIODriver_SPI_SD media_sd_spi;
+ #endif
+
private:
//
// Working directory and parents
@@ -236,7 +271,7 @@ class CardReader {
#if ENABLED(SDSORT_DYNAMIC_RAM)
static uint8_t *isDir;
#elif ENABLED(SDSORT_CACHE_NAMES) || DISABLED(SDSORT_USES_STACK)
- static uint8_t isDir[(SDSORT_LIMIT+7)>>3];
+ static uint8_t isDir[(SDSORT_LIMIT + 7) >> 3];
#endif
#endif
@@ -244,7 +279,7 @@ class CardReader {
#endif // SDCARD_SORT_ALPHA
- static Sd2Card sd2card;
+ static DiskIODriver *driver;
static SdVolume volume;
static SdFile file;
@@ -275,7 +310,7 @@ class CardReader {
};
#if ENABLED(USB_FLASH_DRIVE_SUPPORT)
- #define IS_SD_INSERTED() Sd2Card::isInserted()
+ #define IS_SD_INSERTED() DiskIODriver_USBFlash::isInserted()
#elif PIN_EXISTS(SD_DETECT)
#define IS_SD_INSERTED() (READ(SD_DETECT_PIN) == SD_DETECT_STATE)
#else
diff --git a/Marlin/src/sd/disk_io_driver.h b/Marlin/src/sd/disk_io_driver.h
new file mode 100644
index 000000000000..73c12efcfab0
--- /dev/null
+++ b/Marlin/src/sd/disk_io_driver.h
@@ -0,0 +1,67 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see .
+ *
+ */
+#pragma once
+
+#include
+
+/**
+ * DiskIO Interace
+ *
+ * Interface for low level disk io
+ */
+class DiskIODriver {
+public:
+ /**
+ * Initialize an SD flash memory card with default clock rate and chip
+ * select pin. See sd2Card::init(uint8_t sckRateID, uint8_t chipSelectPin).
+ *
+ * \return true for success or false for failure.
+ */
+ virtual bool init(const uint8_t sckRateID, const pin_t chipSelectPin) = 0; //TODO: only for SPI
+
+ /**
+ * Read a card's CSD register. The CSD contains Card-Specific Data that
+ * provides information regarding access to the card's contents.
+ *
+ * \param[out] csd pointer to area for returned data.
+ *
+ * \return true for success or false for failure.
+ */
+ virtual bool readCSD(csd_t* csd) = 0;
+
+ virtual bool readStart(const uint32_t block) = 0;
+ virtual bool readData(uint8_t* dst) = 0;
+ virtual bool readStop() = 0;
+
+ virtual bool writeStart(const uint32_t block, const uint32_t) = 0;
+ virtual bool writeData(const uint8_t* src) = 0;
+ virtual bool writeStop() = 0;
+
+ virtual bool readBlock(uint32_t block, uint8_t* dst) = 0;
+ virtual bool writeBlock(uint32_t blockNumber, const uint8_t* src) = 0;
+
+ virtual uint32_t cardSize() = 0;
+
+ virtual bool isReady() = 0;
+
+ virtual void idle() = 0;
+};
diff --git a/Marlin/src/sd/usb_flashdrive/Sd2Card_FlashDrive.cpp b/Marlin/src/sd/usb_flashdrive/Sd2Card_FlashDrive.cpp
index dc9efcb672e0..19754184154e 100644
--- a/Marlin/src/sd/usb_flashdrive/Sd2Card_FlashDrive.cpp
+++ b/Marlin/src/sd/usb_flashdrive/Sd2Card_FlashDrive.cpp
@@ -121,7 +121,7 @@ static enum {
uint32_t lun0_capacity;
#endif
-bool Sd2Card::usbStartup() {
+bool DiskIODriver_USBFlash::usbStartup() {
if (state <= DO_STARTUP) {
SERIAL_ECHOPGM("Starting USB host...");
if (!UHS_START) {
@@ -147,7 +147,7 @@ bool Sd2Card::usbStartup() {
// the USB library to monitor for such events. This function also takes care
// of initializing the USB library for the first time.
-void Sd2Card::idle() {
+void DiskIODriver_USBFlash::idle() {
usb.Task();
const uint8_t task_state = usb.getUsbTaskState();
@@ -258,16 +258,16 @@ void Sd2Card::idle() {
// Marlin calls this function to check whether an USB drive is inserted.
// This is equivalent to polling the SD_DETECT when using SD cards.
-bool Sd2Card::isInserted() {
+bool DiskIODriver_USBFlash::isInserted() {
return state == MEDIA_READY;
}
-bool Sd2Card::isReady() {
- return state > DO_STARTUP;
+bool DiskIODriver_USBFlash::isReady() {
+ return state > DO_STARTUP && usb.getUsbTaskState() == UHS_STATE(RUNNING);
}
// Marlin calls this to initialize an SD card once it is inserted.
-bool Sd2Card::init(const uint8_t, const pin_t) {
+bool DiskIODriver_USBFlash::init(const uint8_t, const pin_t) {
if (!isInserted()) return false;
#if USB_DEBUG >= 1
@@ -286,7 +286,7 @@ bool Sd2Card::init(const uint8_t, const pin_t) {
}
// Returns the capacity of the card in blocks.
-uint32_t Sd2Card::cardSize() {
+uint32_t DiskIODriver_USBFlash::cardSize() {
if (!isInserted()) return false;
#if USB_DEBUG < 3
const uint32_t
@@ -295,7 +295,7 @@ uint32_t Sd2Card::cardSize() {
return lun0_capacity;
}
-bool Sd2Card::readBlock(uint32_t block, uint8_t *dst) {
+bool DiskIODriver_USBFlash::readBlock(uint32_t block, uint8_t *dst) {
if (!isInserted()) return false;
#if USB_DEBUG >= 3
if (block >= lun0_capacity) {
@@ -309,7 +309,7 @@ bool Sd2Card::readBlock(uint32_t block, uint8_t *dst) {
return bulk.Read(0, block, 512, 1, dst) == 0;
}
-bool Sd2Card::writeBlock(uint32_t block, const uint8_t *src) {
+bool DiskIODriver_USBFlash::writeBlock(uint32_t block, const uint8_t *src) {
if (!isInserted()) return false;
#if USB_DEBUG >= 3
if (block >= lun0_capacity) {
diff --git a/Marlin/src/sd/usb_flashdrive/Sd2Card_FlashDrive.h b/Marlin/src/sd/usb_flashdrive/Sd2Card_FlashDrive.h
index 320678d091cd..3390bc51becc 100644
--- a/Marlin/src/sd/usb_flashdrive/Sd2Card_FlashDrive.h
+++ b/Marlin/src/sd/usb_flashdrive/Sd2Card_FlashDrive.h
@@ -27,6 +27,7 @@
*/
#include "../SdFatConfig.h"
#include "../SdInfo.h"
+#include "../disk_io_driver.h"
#if DISABLED(USE_OTG_USB_HOST)
/**
@@ -46,7 +47,7 @@
#endif
#endif
-class Sd2Card {
+class DiskIODriver_USBFlash : public DiskIODriver {
private:
uint32_t pos;
@@ -54,25 +55,26 @@ class Sd2Card {
public:
static bool usbStartup();
+ static bool isInserted();
- bool init(const uint8_t sckRateID=0, const pin_t chipSelectPin=TERN(USE_OTG_USB_HOST, 0, SD_CHIP_SELECT_PIN));
+ bool init(const uint8_t sckRateID=0, const pin_t chipSelectPin=TERN(USE_OTG_USB_HOST, 0, SD_CHIP_SELECT_PIN)) override;
- static void idle();
+ inline bool readCSD(csd_t*) override { return true; }
- inline bool readStart(const uint32_t block) { pos = block; return isReady(); }
- inline bool readData(uint8_t *dst) { return readBlock(pos++, dst); }
- inline bool readStop() const { return true; }
+ inline bool readStart(const uint32_t block) override { pos = block; return isReady(); }
+ inline bool readData(uint8_t *dst) override { return readBlock(pos++, dst); }
+ inline bool readStop() override { return true; }
- inline bool writeStart(const uint32_t block, const uint32_t) { pos = block; return isReady(); }
- inline bool writeData(uint8_t *src) { return writeBlock(pos++, src); }
- inline bool writeStop() const { return true; }
+ inline bool writeStart(const uint32_t block, const uint32_t) override { pos = block; return isReady(); }
+ inline bool writeData(const uint8_t *src) override { return writeBlock(pos++, src); }
+ inline bool writeStop() override { return true; }
- bool readBlock(uint32_t block, uint8_t *dst);
- bool writeBlock(uint32_t blockNumber, const uint8_t *src);
+ bool readBlock(uint32_t block, uint8_t *dst) override;
+ bool writeBlock(uint32_t blockNumber, const uint8_t *src) override;
- bool readCSD(csd_t*) { return true; }
+ uint32_t cardSize() override;
- uint32_t cardSize();
- static bool isInserted();
- bool isReady();
+ bool isReady() override;
+
+ void idle() override;
};