forked from openzfs/zfs
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathvdev_id.conf.5
188 lines (161 loc) · 5.28 KB
/
vdev_id.conf.5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
.TH vdev_id.conf 5
.SH NAME
vdev_id.conf \- Configuration file for vdev_id
.SH DESCRIPTION
.I vdev_id.conf
is the configuration file for
.BR vdev_id (8).
It controls the default behavior of
.BR vdev_id (8)
while it is mapping a disk device name to an alias.
.PP
The
.I vdev_id.conf
file uses a simple format consisting of a keyword followed by one or
more values on a single line. Any line not beginning with a recognized
keyword is ignored. Comments may optionally begin with a hash
character.
The following keywords and values are used.
.TP
\fIalias\fR <name> <devlink>
Maps a device link in the /dev directory hierarchy to a new device
name. The udev rule defining the device link must have run prior to
.BR vdev_id (8).
A defined alias takes precedence over a topology-derived name, but the
two naming methods can otherwise coexist. For example, one might name
drives in a JBOD with the sas_direct topology while naming an internal
L2ARC device with an alias.
\fIname\fR - the name of the link to the device that will by created in
/dev/disk/by-vdev.
\fIdevlink\fR - the name of the device link that has already been
defined by udev. This may be an absolute path or the base filename.
.TP
\fIchannel\fR [pci_slot] <port> <name>
Maps a physical path to a channel name (typically representing a single
disk enclosure).
\fIpci_slot\fR - specifies the PCI SLOT of the HBA
hosting the disk enclosure being mapped, as found in the output of
.BR lspci (8).
This argument is not used in sas_switch mode.
\fIport\fR - specifies the numeric identifier of the HBA or SAS switch port
connected to the disk enclosure being mapped.
\fIname\fR - specifies the name of the channel.
.TP
\fIslot\fR <old> <new> [channel]
Maps a disk slot number as reported by the operating system to an
alternative slot number. If the \fIchannel\fR parameter is specified
then the mapping is only applied to slots in the named channel,
otherwise the mapping is applied to all channels. The first-specified
\fIslot\fR rule that can match a slot takes precedence. Therefore a
channel-specific mapping for a given slot should generally appear before
a generic mapping for the same slot. In this way a custom mapping may
be applied to a particular channel and a default mapping applied to the
others.
.TP
\fImultipath\fR <yes|no>
Specifies whether
.BR vdev_id (8)
will handle only dm-multipath devices. If set to "yes" then
.BR vdev_id (8)
will examine the first running component disk of a dm-multipath
device as listed by the
.BR multipath (8)
command to determine the physical path.
.TP
\fItopology\fR <sas_direct|sas_switch>
Identifies a physical topology that governs how physical paths are
mapped to channels.
\fIsas_direct\fR - in this mode a channel is uniquely identified by
a PCI slot and a HBA port number
\fIsas_switch\fR - in this mode a channel is uniquely identified by
a SAS switch port number
.TP
\fIphys_per_port\fR <num>
Specifies the number of PHY devices associated with a SAS HBA port or SAS
switch port.
.BR vdev_id (8)
internally uses this value to determine which HBA or switch port a
device is connected to. The default is 4.
.TP
\fIslot\fR <bay|phy|port|id|lun|ses>
Specifies from which element of a SAS identifier the slot number is
taken. The default is bay.
\fIbay\fR - read the slot number from the bay identifier.
\fIphy\fR - read the slot number from the phy identifier.
\fIport\fR - use the SAS port as the slot number.
\fIid\fR - use the scsi id as the slot number.
\fIlun\fR - use the scsi lun as the slot number.
\fIses\fR - use the SCSI Enclosure Services (SES) enclosure device slot number,
as reported by
.BR sg_ses (8).
This is intended for use only on systems where \fIbay\fR is unsupported,
noting that \fIport\fR and \fIid\fR may be unstable across disk replacement.
.SH EXAMPLES
A non-multipath configuration with direct-attached SAS enclosures and an
arbitrary slot re-mapping.
.P
.nf
multipath no
topology sas_direct
phys_per_port 4
slot bay
# PCI_SLOT HBA PORT CHANNEL NAME
channel 85:00.0 1 A
channel 85:00.0 0 B
channel 86:00.0 1 C
channel 86:00.0 0 D
# Custom mapping for Channel A
# Linux Mapped
# Slot Slot Channel
slot 1 7 A
slot 2 10 A
slot 3 3 A
slot 4 6 A
# Default mapping for B, C, and D
slot 1 4
slot 2 2
slot 3 1
slot 4 3
.fi
.P
A SAS-switch topology. Note that the
.I channel
keyword takes only two arguments in this example.
.P
.nf
topology sas_switch
# SWITCH PORT CHANNEL NAME
channel 1 A
channel 2 B
channel 3 C
channel 4 D
.fi
.P
A multipath configuration. Note that channel names have multiple
definitions - one per physical path.
.P
.nf
multipath yes
# PCI_SLOT HBA PORT CHANNEL NAME
channel 85:00.0 1 A
channel 85:00.0 0 B
channel 86:00.0 1 A
channel 86:00.0 0 B
.fi
.P
A configuration using device link aliases.
.P
.nf
# by-vdev
# name fully qualified or base name of device link
alias d1 /dev/disk/by-id/wwn-0x5000c5002de3b9ca
alias d2 wwn-0x5000c5002def789e
.fi
.P
.SH FILES
.TP
.I /etc/zfs/vdev_id.conf
The configuration file for
.BR vdev_id (8).
.SH SEE ALSO
.BR vdev_id (8)