forked from zephyrproject-rtos/zephyr
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathi2c_npcx_controller.c
1339 lines (1124 loc) · 38.8 KB
/
i2c_npcx_controller.c
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
/*
* Copyright (c) 2020 Nuvoton Technology Corporation.
*
* SPDX-License-Identifier: Apache-2.0
*/
#include <zephyr/pm/policy.h>
#define DT_DRV_COMPAT nuvoton_npcx_i2c_ctrl
/**
* @file
* @brief Nuvoton NPCX smb/i2c module (controller) driver
*
* This file contains the driver of SMB module (controller) which provides full
* support for a two-wire SMBus/I2C synchronous serial interface. The following
* is the state diagrams for each Zephyr i2c api functions.
*
* case 1: i2c_write()/i2c_burst_write()
*
* All msg data sent? Is there next msg?
* +<----------------+<----------------------+
* | No | | Yes
* +------+ +------------+ | +------- ----+ | +------- -------+ |
* +->| IDLE |-->| WAIT_START |--->| WRITE_FIFO |-+--->| WRITE_SUSPEND |--+
* | +------+ +------------+ +------------+ Yes +---------------+ |
* | Issue START START completed | No
* | +-----------+ |
* +--------------------------------------------| WAIT_STOP |<------------+
* STOP is completed +-----------+ Issue STOP
*
*
* case 2: i2c_read()
*
* All msg data received? Is there next msg?
* +<-----------------+<---------------------+
* | No | | Yes
* +------+ +------------+ | +------- ---+ | +------- ------+ |
* +->| IDLE |-->| WAIT_START |--->| READ_FIFO |---+--->| READ_SUSPEND |--+
* | +------+ +------------+ +------------+ Yes +--------------+ |
* | Issue START START completed | No
* | +-----------+ |
* +------------------------------------------| WAIT_STOP |<--------------+
* STOP is completed +-----------+ Issue STOP
*
*
* case 3: i2c_write_read()/i2c_burst_read()
*
* All msg data sent? Is there next write msg?
* +<----------------+<----------------------+
* | No | | Yes
* +------+ +------------+ | +------- ----+ | +------- -------+ |
* +->| IDLE |-->| WAIT_START |--->| WRITE_FIFO |-+--->| WRITE_SUSPEND |--+
* | +------+ +------------+ +------------+ Yes +---------------+ |
* | Issue START START completed | No
* | +---------------------------------------------------------------+
* | |
* | | All msg data received? Is there next read msg?
* | | +<-----------------+<-----------------------+
* | | | No | | Yes
* | | +--------------+ | +------- ---+ | +------- ------+ |
* | +--| WAIT_RESTART |--->| READ_FIFO |---+--->| READ_SUSPEND |----+
* | +--------------+ +-----------+ Yes +--------------+ |
* | Issue RESTART RESTART completed | No
* | +-----------+ |
* +-------------------------------------------| WAIT_STOP |<-------------+
* STOP is completed +-----------+ Issue STOP
*
*/
#include <assert.h>
#include <zephyr/drivers/clock_control.h>
#include <zephyr/drivers/i2c.h>
#include <zephyr/kernel.h>
#include <zephyr/sys/atomic.h>
#include <soc.h>
#include <zephyr/logging/log.h>
#include <zephyr/irq.h>
LOG_MODULE_REGISTER(i2c_npcx, CONFIG_I2C_LOG_LEVEL);
/* I2C controller mode */
#define NPCX_I2C_BANK_NORMAL 0
#define NPCX_I2C_BANK_FIFO 1
/* Timeout for device should be available after reset (SMBus spec. unit:ms) */
#define I2C_MAX_TIMEOUT 35
/* Timeout for SCL held to low by slave device . (SMBus spec. unit:ms). */
#define I2C_MIN_TIMEOUT 25
/* Default maximum time we allow for an I2C transfer (unit:ms) */
#define I2C_TRANS_TIMEOUT K_MSEC(100)
/*
* NPCX I2C module that supports FIFO mode has 32 bytes Tx FIFO and
* 32 bytes Rx FIFO.
*/
#define NPCX_I2C_FIFO_MAX_SIZE 32
/* Valid bit fields in SMBST register */
#define NPCX_VALID_SMBST_MASK ~(BIT(NPCX_SMBST_XMIT) | BIT(NPCX_SMBST_MASTER))
/* The delay for the I2C bus recovery bitbang in ~100K Hz */
#define I2C_RECOVER_BUS_DELAY_US 5
#define I2C_RECOVER_SCL_RETRY 10
#define I2C_RECOVER_SDA_RETRY 3
/* Supported I2C bus frequency */
enum npcx_i2c_freq {
NPCX_I2C_BUS_SPEED_100KHZ,
NPCX_I2C_BUS_SPEED_400KHZ,
NPCX_I2C_BUS_SPEED_1MHZ,
};
enum npcx_i2c_flag {
NPCX_I2C_FLAG_TARGET,
NPCX_I2C_FLAG_COUNT,
};
/*
* Internal SMBus Interface driver states values, which reflect events
* which occurred on the bus
*/
enum npcx_i2c_oper_state {
NPCX_I2C_IDLE,
NPCX_I2C_WAIT_START,
NPCX_I2C_WAIT_RESTART,
NPCX_I2C_WRITE_FIFO,
NPCX_I2C_WRITE_SUSPEND,
NPCX_I2C_READ_FIFO,
NPCX_I2C_READ_SUSPEND,
NPCX_I2C_WAIT_STOP,
NPCX_I2C_ERROR_RECOVERY,
};
/* I2C timing configuration for each i2c speed */
struct npcx_i2c_timing_cfg {
uint8_t HLDT; /* i2c hold-time (Unit: clocks) */
uint8_t k1; /* k1 = SCL low-time (Unit: clocks) */
uint8_t k2; /* k2 = SCL high-time (Unit: clocks) */
};
/* Device config */
struct i2c_ctrl_config {
uintptr_t base; /* i2c controller base address */
struct npcx_clk_cfg clk_cfg; /* clock configuration */
uint8_t irq; /* i2c controller irq */
};
/* Driver data */
struct i2c_ctrl_data {
struct k_sem lock_sem; /* mutex of i2c controller */
struct k_sem sync_sem; /* semaphore used for synchronization */
uint32_t bus_freq; /* operation freq of i2c */
enum npcx_i2c_oper_state oper_state; /* controller operation state */
int trans_err; /* error code during transaction */
struct i2c_msg *msg; /* cache msg for transaction state machine */
int is_write; /* direction of current msg */
uint8_t *ptr_msg; /* current msg pointer for FIFO read/write */
uint16_t addr; /* slave address of transaction */
uint8_t port; /* current port used the controller */
bool is_configured; /* is port configured? */
const struct npcx_i2c_timing_cfg *ptr_speed_confs;
#ifdef CONFIG_I2C_TARGET
struct i2c_target_config *target_cfg;
atomic_t flags;
#endif
};
/* Driver convenience defines */
#define HAL_I2C_INSTANCE(dev) \
((struct smb_reg *)((const struct i2c_ctrl_config *)(dev)->config)->base)
/* Recommended I2C timing values are based on 15 MHz */
static const struct npcx_i2c_timing_cfg npcx_15m_speed_confs[] = {
[NPCX_I2C_BUS_SPEED_100KHZ] = {.HLDT = 15, .k1 = 76, .k2 = 0},
[NPCX_I2C_BUS_SPEED_400KHZ] = {.HLDT = 7, .k1 = 24, .k2 = 18,},
[NPCX_I2C_BUS_SPEED_1MHZ] = {.HLDT = 7, .k1 = 14, .k2 = 10,},
};
static const struct npcx_i2c_timing_cfg npcx_20m_speed_confs[] = {
[NPCX_I2C_BUS_SPEED_100KHZ] = {.HLDT = 15, .k1 = 102, .k2 = 0},
[NPCX_I2C_BUS_SPEED_400KHZ] = {.HLDT = 7, .k1 = 32, .k2 = 22},
[NPCX_I2C_BUS_SPEED_1MHZ] = {.HLDT = 7, .k1 = 16, .k2 = 10},
};
/* I2C controller inline functions access shared registers */
static inline void i2c_ctrl_start(const struct device *dev)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
inst->SMBCTL1 |= BIT(NPCX_SMBCTL1_START);
}
static inline void i2c_ctrl_stop(const struct device *dev)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
inst->SMBCTL1 |= BIT(NPCX_SMBCTL1_STOP);
}
static inline int i2c_ctrl_bus_busy(const struct device *dev)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
return IS_BIT_SET(inst->SMBCST, NPCX_SMBCST_BB);
}
static inline void i2c_ctrl_bank_sel(const struct device *dev, int bank)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
if (bank) {
inst->SMBCTL3 |= BIT(NPCX_SMBCTL3_BNK_SEL);
} else {
inst->SMBCTL3 &= ~BIT(NPCX_SMBCTL3_BNK_SEL);
}
}
static inline void i2c_ctrl_irq_enable(const struct device *dev, int enable)
{
const struct i2c_ctrl_config *const config = dev->config;
if (enable) {
irq_enable(config->irq);
} else {
irq_disable(config->irq);
}
}
/* I2C controller inline functions access registers in 'Normal' bank */
static inline void i2c_ctrl_norm_stall_scl(const struct device *dev)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
/* Enable writing to SCL_LVL/SDA_LVL bit in SMBnCTL3 */
inst->SMBCTL4 |= BIT(NPCX_SMBCTL4_LVL_WE);
/* Force SCL bus to low and keep SDA floating */
inst->SMBCTL3 = (inst->SMBCTL3 & ~BIT(NPCX_SMBCTL3_SCL_LVL))
| BIT(NPCX_SMBCTL3_SDA_LVL);
/* Disable writing to them */
inst->SMBCTL4 &= ~BIT(NPCX_SMBCTL4_LVL_WE);
}
static inline void i2c_ctrl_norm_free_scl(const struct device *dev)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
/* Enable writing to SCL_LVL/SDA_LVL bit in SMBnCTL3 */
inst->SMBCTL4 |= BIT(NPCX_SMBCTL4_LVL_WE);
/*
* Release SCL bus. Then it might be still driven by module itself or
* slave device.
*/
inst->SMBCTL3 |= BIT(NPCX_SMBCTL3_SCL_LVL) | BIT(NPCX_SMBCTL3_SDA_LVL);
/* Disable writing to them */
inst->SMBCTL4 &= ~BIT(NPCX_SMBCTL4_LVL_WE);
}
/* I2C controller inline functions access registers in 'Normal' bank */
static inline void i2c_ctrl_norm_stall_sda(const struct device *dev)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
/* Enable writing to SCL_LVL/SDA_LVL bit in SMBnCTL3 */
inst->SMBCTL4 |= BIT(NPCX_SMBCTL4_LVL_WE);
/* Force SDA bus to low and keep SCL floating */
inst->SMBCTL3 = (inst->SMBCTL3 & ~BIT(NPCX_SMBCTL3_SDA_LVL))
| BIT(NPCX_SMBCTL3_SCL_LVL);
/* Disable writing to them */
inst->SMBCTL4 &= ~BIT(NPCX_SMBCTL4_LVL_WE);
}
static inline void i2c_ctrl_norm_free_sda(const struct device *dev)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
/* Enable writing to SCL_LVL/SDA_LVL bit in SMBnCTL3 */
inst->SMBCTL4 |= BIT(NPCX_SMBCTL4_LVL_WE);
/*
* Release SDA bus. Then it might be still driven by module itself or
* slave device.
*/
inst->SMBCTL3 |= BIT(NPCX_SMBCTL3_SDA_LVL) | BIT(NPCX_SMBCTL3_SCL_LVL);
/* Disable writing to them */
inst->SMBCTL4 &= ~BIT(NPCX_SMBCTL4_LVL_WE);
}
/* I2C controller inline functions access registers in 'FIFO' bank */
static inline void i2c_ctrl_fifo_write(const struct device *dev, uint8_t data)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
inst->SMBSDA = data;
}
static inline uint8_t i2c_ctrl_fifo_read(const struct device *dev)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
return inst->SMBSDA;
}
static inline int i2c_ctrl_fifo_tx_avail(const struct device *dev)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
return NPCX_I2C_FIFO_MAX_SIZE - (inst->SMBTXF_STS & 0x3f);
}
static inline int i2c_ctrl_fifo_rx_occupied(const struct device *dev)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
return inst->SMBRXF_STS & 0x3f;
}
static inline void i2c_ctrl_fifo_rx_setup_threshold_nack(
const struct device *dev, int threshold, int last)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
uint8_t value = MIN(threshold, NPCX_I2C_FIFO_MAX_SIZE);
SET_FIELD(inst->SMBRXF_CTL, NPCX_SMBRXF_CTL_RX_THR, value);
/*
* Is it last received transaction? If so, set LAST bit. Then the
* hardware will generate NACK automatically when receiving last byte.
*/
if (last && (value == threshold)) {
inst->SMBRXF_CTL |= BIT(NPCX_SMBRXF_CTL_LAST);
}
}
static inline void i2c_ctrl_fifo_clear_status(const struct device *dev)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
inst->SMBFIF_CTS |= BIT(NPCX_SMBFIF_CTS_CLR_FIFO);
}
/*
* I2C local functions which touch the registers in 'Normal' bank. These
* utilities will change bank back to FIFO mode when leaving themselves in case
* the other utilities access the registers in 'FIFO' bank.
*/
static void i2c_ctrl_hold_bus(const struct device *dev, int stall)
{
i2c_ctrl_bank_sel(dev, NPCX_I2C_BANK_NORMAL);
if (stall) {
i2c_ctrl_norm_stall_scl(dev);
} else {
i2c_ctrl_norm_free_scl(dev);
}
i2c_ctrl_bank_sel(dev, NPCX_I2C_BANK_FIFO);
}
static void i2c_ctrl_init_module(const struct device *dev)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
i2c_ctrl_bank_sel(dev, NPCX_I2C_BANK_NORMAL);
/* Enable FIFO mode first */
inst->SMBFIF_CTL |= BIT(NPCX_SMBFIF_CTL_FIFO_EN);
/* Enable module - before configuring CTL1 */
inst->SMBCTL2 |= BIT(NPCX_SMBCTL2_ENABLE);
/* Enable SMB interrupt and 'New Address Match' interrupt source */
inst->SMBCTL1 |= BIT(NPCX_SMBCTL1_NMINTE) | BIT(NPCX_SMBCTL1_INTEN);
i2c_ctrl_bank_sel(dev, NPCX_I2C_BANK_FIFO);
}
static void i2c_ctrl_config_bus_freq(const struct device *dev,
enum npcx_i2c_freq bus_freq)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
struct i2c_ctrl_data *const data = dev->data;
const struct npcx_i2c_timing_cfg bus_cfg =
data->ptr_speed_confs[bus_freq];
/* Switch to bank 0 to configure bus speed */
i2c_ctrl_bank_sel(dev, NPCX_I2C_BANK_NORMAL);
/* Configure bus speed */
if (bus_freq == NPCX_I2C_BUS_SPEED_100KHZ) {
/* Enable 'Normal' Mode */
inst->SMBCTL3 &= ~(BIT(NPCX_SMBCTL3_400K));
/* Set freq of SCL. For 100KHz, only k1 is used. */
SET_FIELD(inst->SMBCTL2, NPCX_SMBCTL2_SCLFRQ0_6_FIELD,
bus_cfg.k1/2 & 0x7f);
SET_FIELD(inst->SMBCTL3, NPCX_SMBCTL3_SCLFRQ7_8_FIELD,
bus_cfg.k1/2 >> 7);
SET_FIELD(inst->SMBCTL4, NPCX_SMBCTL4_HLDT_FIELD,
bus_cfg.HLDT);
} else {
/* Enable 'Fast' Mode for 400K or higher freq. */
inst->SMBCTL3 |= BIT(NPCX_SMBCTL3_400K);
/* Set high/low time of SCL and hold-time */
inst->SMBSCLLT = bus_cfg.k1/2;
inst->SMBSCLHT = bus_cfg.k2/2;
SET_FIELD(inst->SMBCTL4, NPCX_SMBCTL4_HLDT_FIELD,
bus_cfg.HLDT);
}
/* Switch to bank 1 to access I2C FIFO registers */
i2c_ctrl_bank_sel(dev, NPCX_I2C_BANK_FIFO);
}
/* I2C controller local functions */
static int i2c_ctrl_wait_stop_completed(const struct device *dev, int timeout)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
if (timeout <= 0) {
return -EINVAL;
}
do {
/*
* Wait till i2c bus is idle. This bit is cleared to 0
* automatically after the STOP condition is generated.
*/
if (!IS_BIT_SET(inst->SMBCTL1, NPCX_SMBCTL1_STOP)) {
break;
}
k_msleep(1);
} while (--timeout);
if (timeout > 0) {
return 0;
} else {
return -ETIMEDOUT;
}
}
static bool i2c_ctrl_is_scl_sda_both_high(const struct device *dev)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
if (IS_BIT_SET(inst->SMBCTL3, NPCX_SMBCTL3_SCL_LVL) &&
IS_BIT_SET(inst->SMBCTL3, NPCX_SMBCTL3_SDA_LVL)) {
return true;
}
return false;
}
static int i2c_ctrl_wait_idle_completed(const struct device *dev, int timeout)
{
if (timeout <= 0) {
return -EINVAL;
}
do {
/* Wait for both SCL & SDA lines are high */
if (i2c_ctrl_is_scl_sda_both_high(dev)) {
break;
}
k_msleep(1);
} while (--timeout);
if (timeout > 0) {
return 0;
} else {
return -ETIMEDOUT;
}
}
static int i2c_ctrl_recovery(const struct device *dev)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
struct i2c_ctrl_data *const data = dev->data;
int ret;
if (data->oper_state != NPCX_I2C_ERROR_RECOVERY) {
data->oper_state = NPCX_I2C_ERROR_RECOVERY;
}
/* Step 1: Make sure the bus is not stalled before exit. */
i2c_ctrl_hold_bus(dev, 0);
/*
* Step 2: Abort data, wait for STOP condition completed.
* - Clearing NEGACK and BER bits first
* - Wait for STOP condition completed
* - Then clear BB (BUS BUSY) bit
*/
inst->SMBST = BIT(NPCX_SMBST_BER) | BIT(NPCX_SMBST_NEGACK);
ret = i2c_ctrl_wait_stop_completed(dev, I2C_MAX_TIMEOUT);
inst->SMBCST |= BIT(NPCX_SMBCST_BB);
if (ret != 0) {
LOG_ERR("Abort i2c port%02x fail! Bus might be stalled.",
data->port);
}
/*
* Step 3: Reset i2c module to clear all internal state machine of it
* - Disable the SMB module first
* - Wait both SCL/SDA line are high
* - Enable i2c module again
*/
inst->SMBCTL2 &= ~BIT(NPCX_SMBCTL2_ENABLE);
ret = i2c_ctrl_wait_idle_completed(dev, I2C_MAX_TIMEOUT);
if (ret != 0) {
LOG_ERR("Reset i2c port%02x fail! Bus might be stalled.",
data->port);
return -EIO;
}
/* Reset module and internal state machine */
i2c_ctrl_init_module(dev);
/* Recovery is completed */
data->oper_state = NPCX_I2C_IDLE;
return 0;
}
static void i2c_ctrl_notify(const struct device *dev, int error)
{
struct i2c_ctrl_data *const data = dev->data;
data->trans_err = error;
k_sem_give(&data->sync_sem);
}
static int i2c_ctrl_wait_completion(const struct device *dev)
{
struct i2c_ctrl_data *const data = dev->data;
if (k_sem_take(&data->sync_sem, I2C_TRANS_TIMEOUT) == 0) {
return data->trans_err;
} else {
return -ETIMEDOUT;
}
}
size_t i2c_ctrl_calculate_msg_remains(const struct device *dev)
{
struct i2c_ctrl_data *const data = dev->data;
uint8_t *buf_end = data->msg->buf + data->msg->len;
return (buf_end > data->ptr_msg) ? (buf_end - data->ptr_msg) : 0;
}
static void i2c_ctrl_handle_write_int_event(const struct device *dev)
{
struct i2c_ctrl_data *const data = dev->data;
/* START condition is issued */
if (data->oper_state == NPCX_I2C_WAIT_START) {
/* Write slave address with W bit */
i2c_ctrl_fifo_write(dev, ((data->addr << 1) & ~BIT(0)));
/* Start to proceed write process */
data->oper_state = NPCX_I2C_WRITE_FIFO;
return;
}
/* Write message data bytes to FIFO */
if (data->oper_state == NPCX_I2C_WRITE_FIFO) {
/* Calculate how many remaining bytes need to transmit */
size_t tx_remain = i2c_ctrl_calculate_msg_remains(dev);
size_t tx_avail = MIN(tx_remain, i2c_ctrl_fifo_tx_avail(dev));
LOG_DBG("tx remains %d, avail %d", tx_remain, tx_avail);
for (int i = 0U; i < tx_avail; i++) {
i2c_ctrl_fifo_write(dev, *(data->ptr_msg++));
}
/* Is there any remaining bytes? */
if (data->ptr_msg == data->msg->buf + data->msg->len) {
data->oper_state = NPCX_I2C_WRITE_SUSPEND;
}
return;
}
/* Issue STOP after sending message? */
if (data->oper_state == NPCX_I2C_WRITE_SUSPEND) {
if (data->msg->flags & I2C_MSG_STOP) {
/* Generate a STOP condition immediately */
i2c_ctrl_stop(dev);
/* Clear rx FIFO threshold and status bits */
i2c_ctrl_fifo_clear_status(dev);
/* Wait for STOP completed */
data->oper_state = NPCX_I2C_WAIT_STOP;
} else {
/* Disable interrupt and handle next message */
i2c_ctrl_irq_enable(dev, 0);
}
}
i2c_ctrl_notify(dev, 0);
}
static void i2c_ctrl_handle_read_int_event(const struct device *dev)
{
struct i2c_ctrl_data *const data = dev->data;
/* START or RESTART condition is issued */
if (data->oper_state == NPCX_I2C_WAIT_START ||
data->oper_state == NPCX_I2C_WAIT_RESTART) {
/* Setup threshold of rx FIFO before sending address byte */
i2c_ctrl_fifo_rx_setup_threshold_nack(dev, data->msg->len,
(data->msg->flags & I2C_MSG_STOP) != 0);
/* Write slave address with R bit */
i2c_ctrl_fifo_write(dev, ((data->addr << 1) | BIT(0)));
/* Start to proceed read process */
data->oper_state = NPCX_I2C_READ_FIFO;
return;
}
/* Read message data bytes from FIFO */
if (data->oper_state == NPCX_I2C_READ_FIFO) {
/* Calculate how many remaining bytes need to receive */
size_t rx_remain = i2c_ctrl_calculate_msg_remains(dev);
size_t rx_occupied = i2c_ctrl_fifo_rx_occupied(dev);
LOG_DBG("rx remains %d, occupied %d", rx_remain, rx_occupied);
/* Is it the last read transaction with STOP condition? */
if (rx_occupied >= rx_remain &&
(data->msg->flags & I2C_MSG_STOP) != 0) {
/*
* Generate a STOP condition before reading data bytes
* from FIFO. It prevents a glitch on SCL.
*/
i2c_ctrl_stop(dev);
} else {
/*
* Hold SCL line here in case the hardware releases bus
* immediately after the driver start to read data from
* FIFO. Then we might lose incoming data from device.
*/
i2c_ctrl_hold_bus(dev, 1);
}
/* Read data bytes from FIFO */
for (int i = 0; i < rx_occupied; i++) {
*(data->ptr_msg++) = i2c_ctrl_fifo_read(dev);
}
rx_remain = i2c_ctrl_calculate_msg_remains(dev);
/* Setup threshold of RX FIFO if needed */
if (rx_remain > 0) {
i2c_ctrl_fifo_rx_setup_threshold_nack(dev, rx_remain,
(data->msg->flags & I2C_MSG_STOP) != 0);
/* Release bus */
i2c_ctrl_hold_bus(dev, 0);
return;
}
}
/* Is the STOP condition issued? */
if ((data->msg->flags & I2C_MSG_STOP) != 0) {
/* Clear rx FIFO threshold and status bits */
i2c_ctrl_fifo_clear_status(dev);
/* Wait for STOP completed */
data->oper_state = NPCX_I2C_WAIT_STOP;
} else {
/* Disable i2c interrupt first */
i2c_ctrl_irq_enable(dev, 0);
data->oper_state = NPCX_I2C_READ_SUSPEND;
}
i2c_ctrl_notify(dev, 0);
}
static int i2c_ctrl_proc_write_msg(const struct device *dev,
struct i2c_msg *msg)
{
struct i2c_ctrl_data *const data = dev->data;
data->is_write = 1;
data->ptr_msg = msg->buf;
data->msg = msg;
if (data->oper_state == NPCX_I2C_IDLE) {
data->oper_state = NPCX_I2C_WAIT_START;
/* Clear FIFO status before starting a new transaction */
i2c_ctrl_fifo_clear_status(dev);
/* Issue a START, wait for transaction completed */
i2c_ctrl_start(dev);
return i2c_ctrl_wait_completion(dev);
} else if (data->oper_state == NPCX_I2C_WRITE_SUSPEND) {
data->oper_state = NPCX_I2C_WRITE_FIFO;
i2c_ctrl_irq_enable(dev, 1);
return i2c_ctrl_wait_completion(dev);
}
LOG_ERR("Unexpected state %d during writing i2c port%02x!",
data->oper_state, data->port);
data->trans_err = -EIO;
return data->trans_err;
}
static int i2c_ctrl_proc_read_msg(const struct device *dev, struct i2c_msg *msg)
{
struct i2c_ctrl_data *const data = dev->data;
data->is_write = 0;
data->ptr_msg = msg->buf;
data->msg = msg;
if (data->oper_state == NPCX_I2C_IDLE) {
data->oper_state = NPCX_I2C_WAIT_START;
/* Clear FIFO status before starting a new transaction */
i2c_ctrl_fifo_clear_status(dev);
/* Issue a START, wait for transaction completed */
i2c_ctrl_start(dev);
return i2c_ctrl_wait_completion(dev);
} else if (data->oper_state == NPCX_I2C_WRITE_SUSPEND) {
data->oper_state = NPCX_I2C_WAIT_RESTART;
/* Issue a RESTART, wait for transaction completed */
i2c_ctrl_start(dev);
i2c_ctrl_irq_enable(dev, 1);
return i2c_ctrl_wait_completion(dev);
} else if (data->oper_state == NPCX_I2C_READ_SUSPEND) {
data->oper_state = NPCX_I2C_READ_FIFO;
/* Setup threshold of RX FIFO first */
i2c_ctrl_fifo_rx_setup_threshold_nack(dev, msg->len,
(msg->flags & I2C_MSG_STOP) != 0);
/* Release bus */
i2c_ctrl_hold_bus(dev, 0);
/* Enable i2c interrupt first */
i2c_ctrl_irq_enable(dev, 1);
return i2c_ctrl_wait_completion(dev);
}
LOG_ERR("Unexpected state %d during reading i2c port%02x!",
data->oper_state, data->port);
data->trans_err = -EIO;
return data->trans_err;
}
/* I2C controller isr function */
#ifdef CONFIG_I2C_TARGET
static void i2c_ctrl_target_isr(const struct device *dev, uint8_t status)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
struct i2c_ctrl_data *const data = dev->data;
const struct i2c_target_callbacks *target_cb = data->target_cfg->callbacks;
uint8_t val = 0;
/* A 'Bus Error' has been identified */
if (IS_BIT_SET(status, NPCX_SMBST_BER)) {
/* Clear BER Bit */
inst->SMBST = BIT(NPCX_SMBST_BER);
/* Notify upper layer the end of transaction */
if (target_cb->stop) {
target_cb->stop(data->target_cfg);
}
/* Reset i2c module in target mode */
inst->SMBCTL2 &= ~BIT(NPCX_SMBCTL2_ENABLE);
inst->SMBCTL2 |= BIT(NPCX_SMBCTL2_ENABLE);
/*
* Re-enable interrupts because they are turned off after the SMBus module
* is reset above.
*/
inst->SMBCTL1 |= BIT(NPCX_SMBCTL1_NMINTE) | BIT(NPCX_SMBCTL1_INTEN);
/* End of transaction */
data->oper_state = NPCX_I2C_IDLE;
LOG_DBG("target: Bus error on port%02x!", data->port);
return;
}
/* A 'Slave Stop' Condition has been identified */
if (IS_BIT_SET(status, NPCX_SMBST_SLVSTP)) {
/* Clear SLVSTP Bit */
inst->SMBST = BIT(NPCX_SMBST_SLVSTP);
/* End of transaction */
data->oper_state = NPCX_I2C_IDLE;
/* Notify upper layer a STOP condition received */
if (target_cb->stop) {
target_cb->stop(data->target_cfg);
}
return;
}
/* A negative acknowledge has occurred */
if (IS_BIT_SET(status, NPCX_SMBST_NEGACK)) {
/* Clear NEGACK Bit */
inst->SMBST = BIT(NPCX_SMBST_NEGACK);
/* Do nothing in i2c target mode */
return;
}
/* A 'Target Address Match' has been identified */
if (IS_BIT_SET(status, NPCX_SMBST_NMATCH)) {
/* Clear NMATCH Bit */
inst->SMBST = BIT(NPCX_SMBST_NMATCH);
/* Distinguish the direction of i2c target mode by reading XMIT bit */
if (IS_BIT_SET(inst->SMBST, NPCX_SMBST_XMIT)) {
/* Start transmitting data in i2c target mode */
data->oper_state = NPCX_I2C_WRITE_FIFO;
/* Write first requested byte after repeated start */
if (target_cb->read_requested) {
target_cb->read_requested(data->target_cfg, &val);
}
inst->SMBSDA = val;
} else {
/* Start receiving data in i2c target mode */
data->oper_state = NPCX_I2C_READ_FIFO;
if (target_cb->write_requested) {
target_cb->write_requested(data->target_cfg);
}
}
return;
}
/* Tx byte empty or Rx byte full has occurred */
if (IS_BIT_SET(status, NPCX_SMBST_SDAST)) {
if (data->oper_state == NPCX_I2C_WRITE_FIFO) {
/* Notify upper layer one byte will be transmitted */
if (target_cb->read_processed) {
target_cb->read_processed(data->target_cfg, &val);
}
inst->SMBSDA = val;
} else if (data->oper_state == NPCX_I2C_READ_FIFO) {
if (target_cb->write_received) {
val = inst->SMBSDA;
/* Notify upper layer one byte received */
target_cb->write_received(data->target_cfg, val);
}
} else {
LOG_ERR("Unexpected oper state %d on i2c target port%02x!",
data->oper_state, data->port);
}
return;
}
/* Clear unexpected status bits */
if (status != 0) {
inst->SMBST = status;
LOG_ERR("Unexpected SMBST 0x%02x occurred on i2c target port%02x!",
status, data->port);
}
}
#endif
/* I2C controller isr function */
static void i2c_ctrl_isr(const struct device *dev)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
struct i2c_ctrl_data *const data = dev->data;
uint8_t status, tmp;
status = inst->SMBST & NPCX_VALID_SMBST_MASK;
LOG_DBG("status: %02x, %d", status, data->oper_state);
#ifdef CONFIG_I2C_TARGET
if (atomic_test_bit(&data->flags, NPCX_I2C_FLAG_TARGET)) {
i2c_ctrl_target_isr(dev, status);
return;
}
#endif
/* A 'Bus Error' has been identified */
if (IS_BIT_SET(status, NPCX_SMBST_BER)) {
/* Generate a STOP condition immediately */
i2c_ctrl_stop(dev);
/* Clear BER Bit */
inst->SMBST = BIT(NPCX_SMBST_BER);
/* Make sure slave doesn't hold bus by reading FIFO again */
tmp = i2c_ctrl_fifo_read(dev);
LOG_ERR("Bus error occurred on i2c port%02x!", data->port);
data->oper_state = NPCX_I2C_ERROR_RECOVERY;
/* I/O error occurred */
i2c_ctrl_notify(dev, -EIO);
return;
}
/* A negative acknowledge has occurred */
if (IS_BIT_SET(status, NPCX_SMBST_NEGACK)) {
/* Generate a STOP condition immediately */
i2c_ctrl_stop(dev);
/* Clear NEGACK Bit */
inst->SMBST = BIT(NPCX_SMBST_NEGACK);
/* End transaction */
data->oper_state = NPCX_I2C_WAIT_STOP;
/* No such device or address */
i2c_ctrl_notify(dev, -ENXIO);
return;
}
/* START, tx FIFO empty or rx FIFO full has occurred */
if (IS_BIT_SET(status, NPCX_SMBST_SDAST)) {
if (data->is_write) {
i2c_ctrl_handle_write_int_event(dev);
} else {
i2c_ctrl_handle_read_int_event(dev);
}
return;
}
/* Clear unexpected status bits */
if (status != 0) {
inst->SMBST = status;
LOG_ERR("Unexpected SMBST 0x%02x occurred on i2c port%02x!",
status, data->port);
}
}
/* NPCX specific I2C controller functions */
void npcx_i2c_ctrl_mutex_lock(const struct device *i2c_dev)
{
struct i2c_ctrl_data *const data = i2c_dev->data;
k_sem_take(&data->lock_sem, K_FOREVER);
}
void npcx_i2c_ctrl_mutex_unlock(const struct device *i2c_dev)
{
struct i2c_ctrl_data *const data = i2c_dev->data;
k_sem_give(&data->lock_sem);
}
int npcx_i2c_ctrl_configure(const struct device *i2c_dev, uint32_t dev_config)
{
struct i2c_ctrl_data *const data = i2c_dev->data;
switch (I2C_SPEED_GET(dev_config)) {
case I2C_SPEED_STANDARD:
data->bus_freq = NPCX_I2C_BUS_SPEED_100KHZ;
break;
case I2C_SPEED_FAST:
data->bus_freq = NPCX_I2C_BUS_SPEED_400KHZ;
break;
case I2C_SPEED_FAST_PLUS:
data->bus_freq = NPCX_I2C_BUS_SPEED_1MHZ;
break;
default:
return -ERANGE;
}
i2c_ctrl_config_bus_freq(i2c_dev, data->bus_freq);
data->is_configured = true;
return 0;
}
int npcx_i2c_ctrl_get_speed(const struct device *i2c_dev, uint32_t *speed)
{
struct i2c_ctrl_data *const data = i2c_dev->data;
if (!data->is_configured) {
return -EIO;
}
switch (data->bus_freq) {
case NPCX_I2C_BUS_SPEED_100KHZ:
*speed = I2C_SPEED_SET(I2C_SPEED_STANDARD);
break;
case NPCX_I2C_BUS_SPEED_400KHZ:
*speed = I2C_SPEED_SET(I2C_SPEED_FAST);
break;
case NPCX_I2C_BUS_SPEED_1MHZ:
*speed = I2C_SPEED_SET(I2C_SPEED_FAST_PLUS);
break;
default:
return -ERANGE;
}
return 0;
}
int npcx_i2c_ctrl_recover_bus(const struct device *dev)
{
struct smb_reg *const inst = HAL_I2C_INSTANCE(dev);
int ret = 0;