.config

### Target Vendor/Product (support only Ralink RT3883/MT7620/MT7621/MT7628)
CONFIG_VENDOR=Ralink
CONFIG_PRODUCT=RT3883

### Target ProductID (board select, max 12 symbols)
CONFIG_FIRMWARE_PRODUCT_ID="RT-N56U"

### Linux kernel and toolchain
CONFIG_LINUXDIR=linux-3.4.x
CONFIG_TOOLCHAIN_DIR=/opt/rt-n56u/toolchain-mipsel

############################################################
### Linux kernel configuration
############################################################

### Build ROOTFS_IN_RAM firmware mode (kernel+initramfs).
### Decreased firmware size, but more RAM used, slow boot.
### Also allow build image for load w/o flash from UART console
#CONFIG_FIRMWARE_TYPE_ROOTFS_IN_RAM=y

### Kernel driver select for WiFi AP 5GHz
### 2.4 = RT3883/3662 v2.4.3.6
### 2.7 = RT3883/3662 v2.7.2.0
CONFIG_FIRMWARE_WIFI5_DRIVER=2.7

### Kernel driver select for WiFi AP 2.4GHz
### 2.4 = RT3092 v2.4.0.5
### 2.5 = RT3092 v2.5.0.11
### 2.7 = RT3092 v2.7.1.5
CONFIG_FIRMWARE_WIFI2_DRIVER=2.7

### Enable IPv6 support
CONFIG_FIRMWARE_ENABLE_IPV6=y

### Enable USB support
CONFIG_FIRMWARE_ENABLE_USB=y

### Enable NTFS filesystem support via Paragon "ufsd" driver. ~0.4MB
CONFIG_FIRMWARE_ENABLE_UFSD=y

### Enable FAT/FAT32 filesystem support. ~0.1MB
CONFIG_FIRMWARE_ENABLE_FAT=y

### Enable exFAT (FAT/FAT32 too) filesystem support. ~0.12MB
CONFIG_FIRMWARE_ENABLE_EXFAT=y

### Enable EXT2 filesystem support. ~0.1MB
#CONFIG_FIRMWARE_ENABLE_EXT2=y

### Enable EXT3 filesystem support. ~0.2MB
#CONFIG_FIRMWARE_ENABLE_EXT3=y

### Enable EXT4 (EXT3/2 too) filesystem support. ~0.4MB
CONFIG_FIRMWARE_ENABLE_EXT4=y

### Enable XFS filesystem support. ~0.6MB
#CONFIG_FIRMWARE_ENABLE_XFS=y

### Enable FUSE (filesystems in userspace) support. ~0.1MB
CONFIG_FIRMWARE_ENABLE_FUSE=y

### Enable swap files/partitions support. ~0.05MB
CONFIG_FIRMWARE_ENABLE_SWAP=y

### Include UVC camera modules. ~0.2MB
#CONFIG_FIRMWARE_INCLUDE_UVC=y

### Include USB-HID modules. ~0.2MB
#CONFIG_FIRMWARE_INCLUDE_HID=y

### Include USB-Serial modules (e.g. pl2303). ~0.03MB
#CONFIG_FIRMWARE_INCLUDE_SERIAL=y

### Include USB-Audio modules ~0.46MB
#CONFIG_FIRMWARE_INCLUDE_AUDIO=y

### Include network QoS scheduling modules. ~0.2MB
#CONFIG_FIRMWARE_INCLUDE_QOS=y

### Include IMQ module for shapers (a bit of performance degradation). ~0.02MB
#CONFIG_FIRMWARE_INCLUDE_IMQ=y

### Include IFB module for shapers. ~0.03MB
#CONFIG_FIRMWARE_INCLUDE_IFB=y

### Include IPSet utility and kernel modules. ~0.4MB
CONFIG_FIRMWARE_INCLUDE_IPSET=y

### Include NFSv3 server. ~0.6MB
CONFIG_FIRMWARE_INCLUDE_NFSD=y

### Include NFSv3 client. ~0.5MB
#CONFIG_FIRMWARE_INCLUDE_NFSC=y

### Include CIFS (SMB) client. ~0.2MB
#CONFIG_FIRMWARE_INCLUDE_CIFS=y

############################################################
### Userspace configuration
############################################################

### Include WebUI international resources. Increased firmware size
#CONFIG_FIRMWARE_INCLUDE_LANG_BR=y
#CONFIG_FIRMWARE_INCLUDE_LANG_CZ=y
#CONFIG_FIRMWARE_INCLUDE_LANG_DA=y
#CONFIG_FIRMWARE_INCLUDE_LANG_DE=y
#CONFIG_FIRMWARE_INCLUDE_LANG_ES=y
#CONFIG_FIRMWARE_INCLUDE_LANG_FI=y
#CONFIG_FIRMWARE_INCLUDE_LANG_FR=y
#CONFIG_FIRMWARE_INCLUDE_LANG_NO=y
#CONFIG_FIRMWARE_INCLUDE_LANG_PL=y
CONFIG_FIRMWARE_INCLUDE_LANG_RU=y
#CONFIG_FIRMWARE_INCLUDE_LANG_SV=y
#CONFIG_FIRMWARE_INCLUDE_LANG_UK=y

### Include NTFS-3G FUSE driver (instead of Paragon "ufsd"). ~0.4MB
#CONFIG_FIRMWARE_INCLUDE_NTFS_3G=y

### Include LPR printer daemon. ~0.12MB
CONFIG_FIRMWARE_INCLUDE_LPRD=y

### Include USB-over-Ethernet printer daemon. ~0.05MB
CONFIG_FIRMWARE_INCLUDE_U2EC=y

### Include "tcpdump" utility. ~0.6MB
#CONFIG_FIRMWARE_INCLUDE_TCPDUMP=y

### Include "hdparm" utility (allow set HDD spindown timeout and APM). ~0.1MB
CONFIG_FIRMWARE_INCLUDE_HDPARM=y

### Include "parted" utility (allow make GPT partitions). ~0.3MB
#CONFIG_FIRMWARE_INCLUDE_PARTED=y

### Include SMB (and WINS) server. ~1.5MB
CONFIG_FIRMWARE_INCLUDE_SMBD=y

### Include WINS server only. ~0.4MB
#CONFIG_FIRMWARE_INCLUDE_WINS=y

### Include syslog for SMB and WINS server. ~0.3MB
#CONFIG_FIRMWARE_INCLUDE_SMBD_SYSLOG=y

### Include FTP server. ~0.2MB
CONFIG_FIRMWARE_INCLUDE_FTPD=y

### Include alternative L2TP control client RP-L2TP. ~0.1MB
#CONFIG_FIRMWARE_INCLUDE_RPL2TP=y

### Include EAP-TTLS and EAP-PEAP authentication support. openssl ~1.2MB, wpa_supplicant +0.04MB
CONFIG_FIRMWARE_INCLUDE_EAP_PEAP=y

### Include HTTPS support for DDNS client. openssl ~1.2MB
CONFIG_FIRMWARE_INCLUDE_DDNS_SSL=y

### Include HTTPS support. openssl ~1.2MB
CONFIG_FIRMWARE_INCLUDE_HTTPS=y

### Include sftp-server. openssl ~1.2MB, sftp-server ~0.06MB
CONFIG_FIRMWARE_INCLUDE_SFTP=y

### Include dropbear SSH. ~0.3MB
CONFIG_FIRMWARE_INCLUDE_DROPBEAR=y

### Make the dropbear symmetrical ciphers and hashes faster. ~0.06MB
CONFIG_FIRMWARE_INCLUDE_DROPBEAR_FAST_CODE=y

### Include OpenSSH instead of dropbear. openssl ~1.2MB, openssh ~1.0MB
#CONFIG_FIRMWARE_INCLUDE_OPENSSH=y

### Include OpenVPN. IPv6 required. openssl ~1.2MB, openvpn ~0.4MB
CONFIG_FIRMWARE_INCLUDE_OPENVPN=y

### Include Elliptic Curves (EC) to openssl library. ~0.1MB
#CONFIG_FIRMWARE_INCLUDE_OPENSSL_EC=y

### Include "openssl" executable for generate certificates. ~0.4MB
CONFIG_FIRMWARE_INCLUDE_OPENSSL_EXE=y

### Include xUPNPd IPTV mediaserver. ~0.3MB
CONFIG_FIRMWARE_INCLUDE_XUPNPD=y

### Include Minidlna UPnP mediaserver. ~1.6MB
CONFIG_FIRMWARE_INCLUDE_MINIDLNA=y

### Include Firefly iTunes mediaserver. ~1.0MB
#CONFIG_FIRMWARE_INCLUDE_FIREFLY=y

### Include ffmpeg 0.11.x instead of 0.6.x for Minidlna and Firefly. ~0.1MB
#CONFIG_FIRMWARE_INCLUDE_FFMPEG_NEW=y

### Include Transmission torrent. openssl ~1.2MB, transmission ~1.5MB
CONFIG_FIRMWARE_INCLUDE_TRANSMISSION=y

### Include Transmission-Web-Control (advanced WebUI). ~0.8MB
#CONFIG_FIRMWARE_INCLUDE_TRANSMISSION_WEB_CONTROL=y

### Include Aria2 download manager. openssl ~1.2MB, aria2 ~3.5MB
#CONFIG_FIRMWARE_INCLUDE_ARIA=y

### Include Aria2 WEB control. ~0.7MB
#CONFIG_FIRMWARE_INCLUDE_ARIA_WEB_CONTROL=y