forked from vedderb/bldc
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathhw_palta.h
227 lines (193 loc) · 6.4 KB
/
hw_palta.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
/*
Copyright 2017 Benjamin Vedder [email protected]
This file is part of the VESC firmware.
The VESC firmware is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
The VESC firmware is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef HW_PALTA_H_
#define HW_PALTA_H_
#define HW_NAME "PALTA"
// HW properties
#define HW_HAS_3_SHUNTS
#define HW_HAS_PHASE_SHUNTS
// Macros
#define ENABLE_GATE() palSetPad(GPIOC, 14)
#define DISABLE_GATE() palClearPad(GPIOC, 14)
#define DCCAL_ON()
#define DCCAL_OFF()
#define IS_DRV_FAULT() (!palReadPad(GPIOB, 12))
#define LED_GREEN_ON() palSetPad(GPIOB, 2)
#define LED_GREEN_OFF() palClearPad(GPIOB, 2)
#define LED_RED_ON() palSetPad(GPIOB, 1)
#define LED_RED_OFF() palClearPad(GPIOB, 1)
#define PALTA_OC_CLR_PORT GPIOB
#define PALTA_OC_CLR_PIN 5
/*
* ADC Vector
*
* 0: IN0 SENS1
* 1: IN1 SENS2
* 2: IN2 SENS3
* 3: IN10 CURR1
* 4: IN11 CURR2
* 5: IN12 CURR3
* 6: IN8 ADC_EXT2
* 7: IN0 SENS1
* 8: IN3 TEMP_PCB
* 9: IN14 TEMP_MOTOR
* 10: IN15 ADC_EXT1
* 11: IN13 AN_IN
* 12: Vrefint
* 13: IN0 SENS1
* 14: IN1 SENS2
*/
#define HW_ADC_CHANNELS 15
#define HW_ADC_INJ_CHANNELS 3
#define HW_ADC_NBR_CONV 5
// ADC Indexes
#define ADC_IND_SENS1 0
#define ADC_IND_SENS2 1
#define ADC_IND_SENS3 2
#define ADC_IND_CURR1 3
#define ADC_IND_CURR2 4
#define ADC_IND_CURR3 5
#define ADC_IND_VIN_SENS 11
#define ADC_IND_EXT 10
#define ADC_IND_EXT2 6
#define ADC_IND_TEMP_MOS 8
#define ADC_IND_TEMP_MOTOR 9
#define ADC_IND_VREFINT 12
// ADC macros and settings
// Component parameters (can be overridden)
#ifndef V_REG
#define V_REG 3.3
#endif
#ifndef VIN_R1
#define VIN_R1 246730.0
#endif
#ifndef VIN_R2
#define VIN_R2 2200.0
#endif
#ifndef CURRENT_AMP_GAIN
#define CURRENT_AMP_GAIN 8.0
#endif
#ifndef CURRENT_SHUNT_RES
#define CURRENT_SHUNT_RES 0.0004852941
#endif
// Input voltage
#define GET_INPUT_VOLTAGE() ((V_REG / 4095.0) * (float)ADC_Value[ADC_IND_VIN_SENS] * ((VIN_R1 + VIN_R2) / VIN_R2))
// NTC Termistors
#define NTC_RES(adc_val) ((4095.0 * 10000.0) / adc_val - 10000.0)
#define NTC_TEMP(adc_ind) (1.0 / ((logf(NTC_RES(ADC_Value[adc_ind]) / 10000.0) / 3434.0) + (1.0 / 298.15)) - 273.15)
#define NTC_RES_MOTOR(adc_val) (10000.0 / ((4095.0 / (float)adc_val) - 1.0)) // Motor temp sensor on low side
#define NTC_TEMP_MOTOR(beta) (1.0 / ((logf(NTC_RES_MOTOR(ADC_Value[ADC_IND_TEMP_MOTOR]) / 10000.0) / beta) + (1.0 / 298.15)) - 273.15)
// Voltage on ADC channel
#define ADC_VOLTS(ch) ((float)ADC_Value[ch] / 4096.0 * V_REG)
// Double samples in beginning and end for positive current measurement.
// Useful when the shunt sense traces have noise that causes offset.
#ifndef CURR1_DOUBLE_SAMPLE
#define CURR1_DOUBLE_SAMPLE 0
#endif
#ifndef CURR2_DOUBLE_SAMPLE
#define CURR2_DOUBLE_SAMPLE 0
#endif
#ifndef CURR3_DOUBLE_SAMPLE
#define CURR3_DOUBLE_SAMPLE 0
#endif
// Number of servo outputs
#define HW_SERVO_NUM 2
// UART Peripheral
#define HW_UART_DEV UARTD3
#define HW_UART_GPIO_AF GPIO_AF_USART3
#define HW_UART_TX_PORT GPIOB
#define HW_UART_TX_PIN 10
#define HW_UART_RX_PORT GPIOB
#define HW_UART_RX_PIN 11
// ICU Peripheral for servo decoding
#define HW_ICU_DEV ICUD4
#define HW_ICU_CHANNEL ICU_CHANNEL_1
#define HW_ICU_GPIO_AF GPIO_AF_TIM4
#define HW_ICU_GPIO GPIOB
#define HW_ICU_PIN 6
// I2C Peripheral
#define HW_I2C_DEV I2CD2
#define HW_I2C_GPIO_AF GPIO_AF_I2C2
#define HW_I2C_SCL_PORT GPIOB
#define HW_I2C_SCL_PIN 10
#define HW_I2C_SDA_PORT GPIOB
#define HW_I2C_SDA_PIN 11
// Hall/encoder pins
#define HW_HALL_ENC_GPIO1 GPIOC
#define HW_HALL_ENC_PIN1 6
#define HW_HALL_ENC_GPIO2 GPIOC
#define HW_HALL_ENC_PIN2 7
#define HW_HALL_ENC_GPIO3 GPIOC
#define HW_HALL_ENC_PIN3 8
#define HW_ENC_TIM TIM3
#define HW_ENC_TIM_AF GPIO_AF_TIM3
#define HW_ENC_TIM_CLK_EN() RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE)
#define HW_ENC_EXTI_PORTSRC EXTI_PortSourceGPIOC
#define HW_ENC_EXTI_PINSRC EXTI_PinSource8
#define HW_ENC_EXTI_CH EXTI9_5_IRQn
#define HW_ENC_EXTI_LINE EXTI_Line8
#define HW_ENC_EXTI_ISR_VEC EXTI9_5_IRQHandler
#define HW_ENC_TIM_ISR_CH TIM3_IRQn
#define HW_ENC_TIM_ISR_VEC TIM3_IRQHandler
// NRF pins
#define NRF_PORT_CSN GPIOB
#define NRF_PIN_CSN 12
#define NRF_PORT_SCK GPIOB
#define NRF_PIN_SCK 4
#define NRF_PORT_MOSI GPIOB
#define NRF_PIN_MOSI 3
#define NRF_PORT_MISO GPIOD
#define NRF_PIN_MISO 2
// SPI pins
#define HW_SPI_DEV SPID1
#define HW_SPI_GPIO_AF GPIO_AF_SPI1
#define HW_SPI_PORT_NSS GPIOA
#define HW_SPI_PIN_NSS 15
#define HW_SPI_PORT_SCK GPIOC
#define HW_SPI_PIN_SCK 10
#define HW_SPI_PORT_MOSI GPIOC
#define HW_SPI_PIN_MOSI 12
#define HW_SPI_PORT_MISO GPIOC
#define HW_SPI_PIN_MISO 11
// Measurement macros
#define ADC_V_L1 ADC_Value[ADC_IND_SENS1]
#define ADC_V_L2 ADC_Value[ADC_IND_SENS2]
#define ADC_V_L3 ADC_Value[ADC_IND_SENS3]
#define ADC_V_ZERO (ADC_Value[ADC_IND_VIN_SENS] / 2)
// Macros
#define READ_HALL1() palReadPad(HW_HALL_ENC_GPIO1, HW_HALL_ENC_PIN1)
#define READ_HALL2() palReadPad(HW_HALL_ENC_GPIO2, HW_HALL_ENC_PIN2)
#define READ_HALL3() palReadPad(HW_HALL_ENC_GPIO3, HW_HALL_ENC_PIN3)
// Override dead time. See the stm32f4 reference manual for calculating this value.
#define HW_DEAD_TIME_VALUE 202
// Default setting overrides
#ifndef MCCONF_DEFAULT_MOTOR_TYPE
#define MCCONF_DEFAULT_MOTOR_TYPE MOTOR_TYPE_FOC
#endif
#ifndef MCCONF_FOC_SAMPLE_V0_V7
#define MCCONF_FOC_SAMPLE_V0_V7 true // Run control loop in both v0 and v7 (requires phase shunts)
#endif
// Setting limits (TODO: Configure these)
//#define HW_LIM_CURRENT -100.0, 100.0
//#define HW_LIM_CURRENT_IN -100.0, 100.0
//#define HW_LIM_CURRENT_ABS 0.0, 150.0
//#define HW_LIM_VIN 6.0, 57.0
//#define HW_LIM_ERPM -200e3, 200e3
//#define HW_LIM_DUTY_MIN 0.0, 0.1
//#define HW_LIM_DUTY_MAX 0.0, 1.0
//#define HW_LIM_TEMP_FET -40.0, 110.0
// HW-specific functions
void hw_palta_reset_oc(void);
#endif /* HW_PALTA_H_ */