CI: add PR focused workflow

Add workflow that will build the branch that is aimed at finally making
a PR to get the target into OpenWrt.

Signed-off-by: Robert Marko <[email protected]>

CI: add PR focused workflow

Add workflow that will build the branch that is aimed at finally making
a PR to get the target into OpenWrt.

Signed-off-by: Robert Marko <[email protected]>

CI: add PR focused workflow

Add workflow that will build the branch that is aimed at finally making
a PR to get the target into OpenWrt.

Signed-off-by: Robert Marko <[email protected]>

CI: add PR focused workflow

Add workflow that will build the branch that is aimed at finally making
a PR to get the target into OpenWrt.

Signed-off-by: Robert Marko <[email protected]>

CI: add PR focused workflow

Add workflow that will build the branch that is aimed at finally making
a PR to get the target into OpenWrt.

Signed-off-by: Robert Marko <[email protected]>

CI: add PR focused workflow

Add workflow that will build the branch that is aimed at finally making
a PR to get the target into OpenWrt.

Signed-off-by: Robert Marko <[email protected]>

CI: add PR focused workflow

Add workflow that will build the branch that is aimed at finally making
a PR to get the target into OpenWrt.

Signed-off-by: Robert Marko <[email protected]>

ipq807x: add Dynalink DL-WRX36

Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports.

Specifications:

    •     CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
    •     RAM: 1024MB of DDR3
    •     Storage: 256MB Nand
    •     Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
    •     WLAN:
          2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate
          5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
    •     1x USB 3.0

    •     1 gpio-controlled dual color led (blue/red)

            • Buttons: 1x soft reset / 1x WPS
            • Power: 12V DC jack

        A poulated serial header is onboard (J1004)
        the connector size is a 4-pin 2.0 mm JST PH.
        RX/TX is working, u-boot bootwait is active, secure boot is enabled.

        Note: serial is completely deactivated in the stock firmware image.

        Installation Instructions:

            • obtain serial access
            • stop auto boot
            • saveenv (write the default env to the flash)
            • check which mtd-part is rootfs by invoking "smeminfo"

		It's either:

		18: rootfs           0x0000ffff        0x7a00000        0x6100000

		or:

		18: rootfs         0x0000ffff        0x1000000        0x6100000

		Set mtdids:

		setenv mtdids nand0=nand0

		if rootfs is: 0x7a00000        0x6100000

		setenv mtdparts mtdparts=nand0:0x6100000@0x7a00000(fs)

		if rootfs is: 0x1000000        0x6100000

		setenv mtdparts mtdparts=nand0:0x6100000@0x1000000(fs)

		saveenv

            • tftpboot the initramfs image
              (openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-fit-uImage.itb)

            • bootm

            • Check the rootfs partition number:
	      cat /proc/mtd
	      rootfs should be mtd18

            • SCP the factory image to the device and do a ubiformat
              to the right rootfs partition:

	      ubiformat /dev/mtd18 -y -f /path_to/factory_image

            • Due to secure boot is active, we need to change the bootcmd to:

	      fw_setenv bootcmd "setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs
	      root=mtd:rootfs rootfstype=squashfs rootwait; ubi part fs;
	      ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0"

            • reboot

        Note: this PR adds only single partition support, that means sysupgrade is
              upgrading the current rootfs partition

Signed-off-by: Dirk Buchwalder <[email protected]>

image-commands: make use of gzip-libdeflate

Now that we provide a better gzip compression tool we can make use of
it whereever gzip is used. Change Build/gzip command to new gzip-libdeflate
compressor.

Signed-off-by: Markus Stockhausen <[email protected]>

image-commands: make use of gzip-libdeflate

Now that we provide a better gzip compression tool we can make use of
it whereever gzip is used. Change Build/gzip command to new gzip-libdeflate
compressor.

Signed-off-by: Markus Stockhausen <[email protected]>