leds: Add LED driver for lm3556 chip

LM3556 :
The LM3556 is a 4 MHz fixed-frequency synchronous boost
converter plus 1.5A constant current driver for a high-current white LED.
Datasheet: www.national.com/ds/LM/LM3556.pdf

Tested on OMAP4430

([email protected]: use module_i2c_driver() rather than
lm3556_init/lm3556_exit for code simplicity; fixed some typo
pointed out by Rob Landley)

Signed-off-by: G.Shark Jeong <[email protected]>
Reviewed-by: Axel Lin <[email protected]>
Reviewed-by: Kim, Milo <[email protected]>
Acked-by: Rob Landley <[email protected]>
Signed-off-by: Bryan Wu <[email protected]>

Documentation/leds/00-INDEX

@@ -6,3 +6,5 @@ leds-lp5521.txt
 	- notes on how to use the leds-lp5521 driver.
 leds-lp5523.txt
 	- notes on how to use the leds-lp5523 driver.
+leds-lm3556.txt
+	- notes on how to use the leds-lm3556 driver.

Documentation/leds/leds-lm3556.txt

@@ -0,0 +1,85 @@
+Kernel driver for lm3556
+========================
+
+*Texas Instrument:
+ 1.5 A Synchronous Boost LED Flash Driver w/ High-Side Current Source
+* Datasheet: http://www.national.com/ds/LM/LM3556.pdf
+
+Authors:
+	Daniel Jeong
+	Contact:Daniel Jeong(daniel.jeong-at-ti.com, gshark.jeong-at-gmail.com)
+
+Description
+-----------
+There are 3 functions in LM3556, Flash, Torch and Indicator.
+
+FLASH MODE
+In Flash Mode, the LED current source(LED) provides 16 target current levels
+from 93.75 mA to 1500 mA.The Flash currents are adjusted via the CURRENT
+CONTROL REGISTER(0x09).Flash mode is activated by the ENABLE REGISTER(0x0A),
+or by pulling the STROBE pin HIGH.
+LM3556 Flash can be controlled through sys/class/leds/flash/brightness file
+* if STROBE pin is enabled, below example control brightness only, and
+ON / OFF will be controlled by STROBE pin.
+
+Flash Example:
+OFF     : #echo 0 > sys/class/leds/flash/brightness
+93.75 mA: #echo 1 > sys/class/leds/flash/brightness
+... .....
+1500  mA: #echo 16 > sys/class/leds/flash/brightness
+
+TORCH MODE
+In Torch Mode, the current source(LED) is programmed via the CURRENT CONTROL
+REGISTER(0x09).Torch Mode is activated by the ENABLE REGISTER(0x0A) or by the
+hardware TORCH input.
+LM3556 torch can be controlled through sys/class/leds/torch/brightness file.
+* if TORCH pin is enabled, below example control brightness only,
+and ON / OFF will be controlled by TORCH pin.
+
+Torch Example:
+OFF     : #echo 0 > sys/class/leds/torch/brightness
+46.88 mA: #echo 1 > sys/class/leds/torch/brightness
+... .....
+375 mA  : #echo 8 > sys/class/leds/torch/brightness
+
+INDICATOR MODE
+Indicator pattern can be set through sys/class/leds/indicator/pattern file,
+and 4 patterns are pre-defined in indicator_pattern array.
+According to N-lank, Pulse time and N Period values, different pattern wiill
+be generated.If you want new patterns for your own device, change
+indicator_pattern array with your own values and INDIC_PATTERN_SIZE.
+Please refer datasheet for more detail about N-Blank, Pulse time and N Period.
+
+Indicator pattern example:
+pattern 0: #echo 0 > sys/class/leds/indicator/pattern
+....
+pattern 3: #echo 3 > sys/class/leds/indicator/pattern
+
+Indicator brightness can be controlled through
+sys/class/leds/indicator/brightness file.
+
+Example:
+OFF      : #echo 0 > sys/class/leds/indicator/brightness
+5.86 mA  : #echo 1 > sys/class/leds/indicator/brightness
+........
+46.875mA : #echo 8 > sys/class/leds/indicator/brightness
+
+Notes
+-----
+Driver expects it is registered using the i2c_board_info mechanism.
+To register the chip at address 0x63 on specific adapter, set the platform data
+according to include/linux/platform_data/leds-lm3556.h, set the i2c board info
+
+Example:
+	static struct i2c_board_info __initdata board_i2c_ch4[]	= {
+		{
+			 I2C_BOARD_INFO(LM3556_NAME, 0x63),
+			 .platform_data = &lm3556_pdata,
+		 },
+	};
+
+and register it in the platform init function
+
+Example:
+	board_register_i2c_bus(4, 400,
+				board_i2c_ch4, ARRAY_SIZE(board_i2c_ch4));

drivers/leds/Kconfig

@@ -415,6 +415,14 @@ config LEDS_MAX8997
 	  This option enables support for on-chip LED drivers on
 	  MAXIM MAX8997 PMIC.
 
+config LEDS_LM3556
+	tristate "LED support for LM3556 Chip"
+	depends on LEDS_CLASS && I2C
+	select REGMAP_I2C
+	help
+	  This option enables support for LEDs connected to LM3556.
+	  LM3556 includes Torch, Flash and Indicator functions.
+
 config LEDS_OT200
 	tristate "LED support for the Bachmann OT200"
 	depends on LEDS_CLASS && HAS_IOMEM

drivers/leds/Makefile

@@ -47,6 +47,7 @@ obj-$(CONFIG_LEDS_NETXBIG)		+= leds-netxbig.o
 obj-$(CONFIG_LEDS_ASIC3)		+= leds-asic3.o
 obj-$(CONFIG_LEDS_RENESAS_TPU)		+= leds-renesas-tpu.o
 obj-$(CONFIG_LEDS_MAX8997)		+= leds-max8997.o
+obj-$(CONFIG_LEDS_LM3556)		+= leds-lm3556.o
 
 # LED SPI Drivers
 obj-$(CONFIG_LEDS_DAC124S085)		+= leds-dac124s085.o