Merge tag 'omap-for-v4.2/wakeirq-drivers-v2' of git://git.kernel.org/…

…pub/scm/linux/kernel/git/tmlind/linux-omap into next/late Merge "omap generic wakeirq for v4.2 merge window" from Tony Lindgren: Omap driver changes for v4.2 to switch drivers over to Linux generic wake IRQ events for omap_hsmmc, 8250_omap and omap-serial drivers. The generic wake IRQs also fix issues that these drivers potentially have with IRQ re-entrancy at least for serial-omap. Note that because of dependencies and merge conflicts these are based on Rafael's pm-wakeirq and Greg's tty-next branches. * tag 'omap-for-v4.2/wakeirq-drivers-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (148 commits) serial: 8250_omap: Move wake-up interrupt to generic wakeirq serial: omap: Switch wake-up interrupt to generic wakeirq tty: move linux/gsmmux.h to uapi doc: dt: add documentation for nxp,lpc1850-uart serial: 8250: add LPC18xx/43xx UART driver serial: 8250_uniphier: add UniPhier serial driver serial: 8250_dw: support ACPI platforms with integrated DMA engine serial: of_serial: check the return value of clk_prepare_enable() serial: of_serial: use devm_clk_get() instead of clk_get() serial: earlycon: Add support for big-endian MMIO accesses serial: sirf: use hrtimer for data rx serial: sirf: correct the fifo empty_bit serial: sirf: fix system hung on console log output serial: 8250: remove return statements from void function sc16is7xx: use kworker for RS-485 configuration sc16is7xx: use kworker to update ier bits sc16is7xx: use kworker for md_proc sc16is7xx: move RTS delay to workqueue sc16is7xx: use kthread_worker for tx_work and irq sc16is7xx: use LSR_TEMT_BIT in .tx_empty() ...
CamonZ · Jul 1, 2015 · 593aae2 · 593aae2
2 parents ea21feb + 63e63a1
commit 593aae2
Show file tree

Hide file tree

Showing 101 changed files with 2,891 additions and 1,889 deletions.
diff --git a/Documentation/devicetree/bindings/serial/arm_sbsa_uart.txt b/Documentation/devicetree/bindings/serial/arm_sbsa_uart.txt
@@ -0,0 +1,10 @@
+* ARM SBSA defined generic UART
+This UART uses a subset of the PL011 registers and consequently lives
+in the PL011 driver. It's baudrate and other communication parameters
+cannot be adjusted at runtime, so it lacks a clock specifier here.
+
+Required properties:
+- compatible: must be "arm,sbsa-uart"
+- reg: exactly one register range
+- interrupts: exactly one interrupt specifier
+- current-speed: the (fixed) baud rate set by the firmware
diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt
@@ -14,13 +14,21 @@ Required properties:
 
 - interrupts: A single interrupt specifier.
 
-- clocks: Clock driving the hardware.
+- clocks : Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names:
+  - "baud": The clock the baudrate is derived from
+  - "bus": The bus clock for register accesses (optional)
+
+For compatibility with older device trees an unnamed clock is used for the
+baud clock if the baudclk does not exist. Do not use this for new designs.
 
 Example:
 
 	uart0: serial@11006000 {
 		compatible = "mediatek,mt6589-uart", "mediatek,mt6577-uart";
 		reg = <0x11006000 0x400>;
 		interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>;
-		clocks = <&uart_clk>;
+		clocks = <&uart_clk>, <&bus_clk>;
+		clock-names = "baud", "bus";
 	};
diff --git a/Documentation/devicetree/bindings/serial/nxp,lpc1850-uart.txt b/Documentation/devicetree/bindings/serial/nxp,lpc1850-uart.txt
@@ -0,0 +1,28 @@
+* NXP LPC1850 UART
+
+Required properties:
+- compatible	: "nxp,lpc1850-uart", "ns16550a".
+- reg		: offset and length of the register set for the device.
+- interrupts	: should contain uart interrupt.
+- clocks	: phandle to the input clocks.
+- clock-names	: required elements: "uartclk", "reg".
+
+Optional properties:
+- dmas		: Two or more DMA channel specifiers following the
+		  convention outlined in bindings/dma/dma.txt
+- dma-names	: Names for the dma channels, if present. There must
+		  be at least one channel named "tx" for transmit
+		  and named "rx" for receive.
+
+Since it's also possible to also use the of_serial.c driver all
+parameters from 8250.txt also apply but are optional.
+
+Example:
+uart0: serial@40081000 {
+	compatible = "nxp,lpc1850-uart", "ns16550a";
+	reg = <0x40081000 0x1000>;
+	reg-shift = <2>;
+	interrupts = <24>;
+	clocks = <&ccu2 CLK_APB0_UART0>, <&ccu1 CLK_CPU_UART0>;
+	clock-names = "uartclk", "reg";
+};
diff --git a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt
@@ -1,4 +1,5 @@
 * NXP SC16IS7xx advanced Universal Asynchronous Receiver-Transmitter (UART)
+* i2c as bus
 
 Required properties:
 - compatible: Should be one of the following:
@@ -31,3 +32,39 @@ Example:
                 gpio-controller;
                 #gpio-cells = <2>;
         };
+
+* spi as bus
+
+Required properties:
+- compatible: Should be one of the following:
+  - "nxp,sc16is740" for NXP SC16IS740,
+  - "nxp,sc16is741" for NXP SC16IS741,
+  - "nxp,sc16is750" for NXP SC16IS750,
+  - "nxp,sc16is752" for NXP SC16IS752,
+  - "nxp,sc16is760" for NXP SC16IS760,
+  - "nxp,sc16is762" for NXP SC16IS762.
+- reg: SPI chip select number.
+- interrupt-parent: The phandle for the interrupt controller that
+  services interrupts for this IC.
+- interrupts: Specifies the interrupt source of the parent interrupt
+  controller. The format of the interrupt specifier depends on the
+  parent interrupt controller.
+- clocks: phandle to the IC source clock.
+
+Optional properties:
+- gpio-controller: Marks the device node as a GPIO controller.
+- #gpio-cells: Should be two. The first cell is the GPIO number and
+  the second cell is used to specify the GPIO polarity:
+    0 = active high,
+    1 = active low.
+
+Example:
+	sc16is750: sc16is750@0 {
+		compatible = "nxp,sc16is750";
+		reg = <0>;
+		clocks = <&clk20m>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt
@@ -44,6 +44,11 @@ Required properties:
 Note: Each enabled SCIx UART should have an alias correctly numbered in the
 "aliases" node.
 
+Optional properties:
+  - dmas: Must contain a list of two references to DMA specifiers, one for
+	  transmission, and one for reception.
+  - dma-names: Must contain a list of two DMA names, "tx" and "rx".
+
 Example:
 	aliases {
 		serial0 = &scifa0;
@@ -56,4 +61,6 @@ Example:
 		interrupts = <0 144 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp2_clks R8A7790_CLK_SCIFA0>;
 		clock-names = "sci_ick";
+		dmas = <&dmac0 0x21>, <&dmac0 0x22>;
+		dma-names = "tx", "rx";
 	};
diff --git a/Documentation/devicetree/bindings/serial/sirf-uart.txt b/Documentation/devicetree/bindings/serial/sirf-uart.txt
@@ -2,8 +2,7 @@
 
 Required properties:
 - compatible : Should be "sirf,prima2-uart", "sirf, prima2-usp-uart",
-		"sirf,atlas7-uart" or "sirf,atlas7-bt-uart" which means
-		uart located in BT module and used for BT.
+		"sirf,atlas7-uart" or "sirf,atlas7-usp-uart".
 - reg : Offset and length of the register set for the device
 - interrupts : Should contain uart interrupt
 - fifosize : Should define hardware rx/tx fifo size
@@ -33,15 +32,3 @@ usp@b0090000 {
 	rts-gpios = <&gpio 15 0>;
 	cts-gpios = <&gpio 46 0>;
 };
-
-for uart use in BT module,
-uart6: uart@11000000 {
-	cell-index = <6>;
-	compatible = "sirf,atlas7-bt-uart", "sirf,atlas7-uart";
-	reg = <0x11000000 0x1000>;
-	interrupts = <0 100 0>;
-	clocks = <&clks 138>, <&clks 140>, <&clks 141>;
-	clock-names = "uart", "general", "noc";
-	fifosize = <128>;
-	status = "disabled";
-}
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
@@ -959,14 +959,15 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 		uart[8250],io,<addr>[,options]
 		uart[8250],mmio,<addr>[,options]
 		uart[8250],mmio32,<addr>[,options]
+		uart[8250],mmio32be,<addr>[,options]
 		uart[8250],0x<addr>[,options]
 			Start an early, polled-mode console on the 8250/16550
 			UART at the specified I/O port or MMIO address.
 			MMIO inter-register address stride is either 8-bit
-			(mmio) or 32-bit (mmio32).
-			If none of [io|mmio|mmio32], <addr> is assumed to be
-			equivalent to 'mmio'. 'options' are specified in the
-			same format described for "console=ttyS<n>"; if
+			(mmio) or 32-bit (mmio32 or mmio32be).
+			If none of [io|mmio|mmio32|mmio32be], <addr> is assumed
+			to be equivalent to 'mmio'. 'options' are specified
+			in the same format described for "console=ttyS<n>"; if
 			unspecified, the h/w is not initialized.
 
 		pl011,<addr>

diff --git a/Documentation/power/runtime_pm.txt b/Documentation/power/runtime_pm.txt
@@ -556,6 +556,12 @@ helper functions described in Section 4.  In that case, pm_runtime_resume()
 should be used.  Of course, for this purpose the device's runtime PM has to be
 enabled earlier by calling pm_runtime_enable().
 
+Note, if the device may execute pm_runtime calls during the probe (such as
+if it is registers with a subsystem that may call back in) then the
+pm_runtime_get_sync() call paired with a pm_runtime_put() call will be
+appropriate to ensure that the device is not put back to sleep during the
+probe. This can happen with systems such as the network device layer.
+
 It may be desirable to suspend the device once ->probe() has finished.
 Therefore the driver core uses the asyncronous pm_request_idle() to submit a
 request to execute the subsystem-level idle callback for the device at that

diff --git a/arch/alpha/include/asm/serial.h b/arch/alpha/include/asm/serial.h
@@ -13,7 +13,7 @@
 #define BASE_BAUD ( 1843200 / 16 )
 
 /* Standard COM flags (except for COM4, because of the 8514 problem) */
-#ifdef CONFIG_SERIAL_DETECT_IRQ
+#ifdef CONFIG_SERIAL_8250_DETECT_IRQ
 #define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ)
 #define STD_COM4_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_AUTO_IRQ)
 #else

diff --git a/arch/arm/common/edma.c b/arch/arm/common/edma.c
@@ -1350,6 +1350,9 @@ void edma_stop(unsigned channel)
 		edma_shadow0_write_array(ctlr, SH_SECR, j, mask);
 		edma_write_array(ctlr, EDMA_EMCR, j, mask);
 
+		/* clear possibly pending completion interrupt */
+		edma_shadow0_write_array(ctlr, SH_ICR, j, mask);
+
 		pr_debug("EDMA: EER%d %08x\n", j,
 				edma_shadow0_read_array(ctlr, SH_EER, j));
 

diff --git a/arch/blackfin/include/asm/bfin_serial.h b/arch/blackfin/include/asm/bfin_serial.h
@@ -22,9 +22,9 @@
     defined(CONFIG_BFIN_UART2_CTSRTS) || \
     defined(CONFIG_BFIN_UART3_CTSRTS)
 # if defined(BFIN_UART_BF54X_STYLE) || defined(BFIN_UART_BF60X_STYLE)
-#  define CONFIG_SERIAL_BFIN_HARD_CTSRTS
+#  define SERIAL_BFIN_HARD_CTSRTS
 # else
-#  define CONFIG_SERIAL_BFIN_CTSRTS
+#  define SERIAL_BFIN_CTSRTS
 # endif
 #endif
 
@@ -50,8 +50,8 @@ struct bfin_serial_port {
 #elif ANOMALY_05000363
 	unsigned int anomaly_threshold;
 #endif
-#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
-	defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
+#if defined(SERIAL_BFIN_CTSRTS) || \
+	defined(SERIAL_BFIN_HARD_CTSRTS)
 	int cts_pin;
 	int rts_pin;
 #endif

diff --git a/arch/m68k/include/asm/serial.h b/arch/m68k/include/asm/serial.h
@@ -17,7 +17,7 @@
 #define BASE_BAUD ( 1843200 / 16 )
 
 /* Standard COM flags (except for COM4, because of the 8514 problem) */
-#ifdef CONFIG_SERIAL_DETECT_IRQ
+#ifdef CONFIG_SERIAL_8250_DETECT_IRQ
 #define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ)
 #define STD_COM4_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_AUTO_IRQ)
 #else

diff --git a/arch/mn10300/include/asm/serial.h b/arch/mn10300/include/asm/serial.h
@@ -13,15 +13,15 @@
 #define _ASM_SERIAL_H
 
 /* Standard COM flags (except for COM4, because of the 8514 problem) */
-#ifdef CONFIG_SERIAL_DETECT_IRQ
+#ifdef CONFIG_SERIAL_8250_DETECT_IRQ
 #define STD_COM_FLAGS	(ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ)
 #define STD_COM4_FLAGS	(ASYNC_BOOT_AUTOCONF | ASYNC_AUTO_IRQ)
 #else
 #define STD_COM_FLAGS	(ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST)
 #define STD_COM4_FLAGS	ASYNC_BOOT_AUTOCONF
 #endif
 
-#ifdef CONFIG_SERIAL_MANY_PORTS
+#ifdef CONFIG_SERIAL_8250_MANY_PORTS
 #define FOURPORT_FLAGS	ASYNC_FOURPORT
 #define ACCENT_FLAGS	0
 #define BOCA_FLAGS	0

diff --git a/arch/x86/include/asm/serial.h b/arch/x86/include/asm/serial.h
@@ -11,7 +11,7 @@
 #define BASE_BAUD (1843200/16)
 
 /* Standard COM flags (except for COM4, because of the 8514 problem) */
-#ifdef CONFIG_SERIAL_DETECT_IRQ
+#ifdef CONFIG_SERIAL_8250_DETECT_IRQ
 # define STD_COMX_FLAGS	(UPF_BOOT_AUTOCONF |	UPF_SKIP_TEST	| UPF_AUTO_IRQ)
 # define STD_COM4_FLAGS	(UPF_BOOT_AUTOCONF |	0		| UPF_AUTO_IRQ)
 #else

diff --git a/drivers/base/power/Makefile b/drivers/base/power/Makefile
@@ -1,4 +1,4 @@
-obj-$(CONFIG_PM)	+= sysfs.o generic_ops.o common.o qos.o runtime.o
+obj-$(CONFIG_PM)	+= sysfs.o generic_ops.o common.o qos.o runtime.o wakeirq.o
 obj-$(CONFIG_PM_SLEEP)	+= main.o wakeup.o
 obj-$(CONFIG_PM_TRACE_RTC)	+= trace.o
 obj-$(CONFIG_PM_OPP)	+= opp.o

diff --git a/drivers/base/power/main.c b/drivers/base/power/main.c
@@ -24,6 +24,7 @@
 #include <linux/pm.h>
 #include <linux/pm_runtime.h>
 #include <linux/pm-trace.h>
+#include <linux/pm_wakeirq.h>
 #include <linux/interrupt.h>
 #include <linux/sched.h>
 #include <linux/async.h>
@@ -587,6 +588,7 @@ void dpm_resume_noirq(pm_message_t state)
 	async_synchronize_full();
 	dpm_show_time(starttime, state, "noirq");
 	resume_device_irqs();
+	device_wakeup_disarm_wake_irqs();
 	cpuidle_resume();
 	trace_suspend_resume(TPS("dpm_resume_noirq"), state.event, false);
 }
@@ -1104,6 +1106,7 @@ int dpm_suspend_noirq(pm_message_t state)
 
 	trace_suspend_resume(TPS("dpm_suspend_noirq"), state.event, true);
 	cpuidle_pause();
+	device_wakeup_arm_wake_irqs();
 	suspend_device_irqs();
 	mutex_lock(&dpm_list_mtx);
 	pm_transition = state;

diff --git a/drivers/base/power/power.h b/drivers/base/power/power.h
@@ -20,6 +20,46 @@ static inline void pm_runtime_early_init(struct device *dev)
 extern void pm_runtime_init(struct device *dev);
 extern void pm_runtime_remove(struct device *dev);
 
+struct wake_irq {
+	struct device *dev;
+	int irq;
+	bool dedicated_irq:1;
+};
+
+extern void dev_pm_arm_wake_irq(struct wake_irq *wirq);
+extern void dev_pm_disarm_wake_irq(struct wake_irq *wirq);
+
+#ifdef CONFIG_PM_SLEEP
+
+extern int device_wakeup_attach_irq(struct device *dev,
+				    struct wake_irq *wakeirq);
+extern void device_wakeup_detach_irq(struct device *dev);
+extern void device_wakeup_arm_wake_irqs(void);
+extern void device_wakeup_disarm_wake_irqs(void);
+
+#else
+
+static inline int
+device_wakeup_attach_irq(struct device *dev,
+			 struct wake_irq *wakeirq)
+{
+	return 0;
+}
+
+static inline void device_wakeup_detach_irq(struct device *dev)
+{
+}
+
+static inline void device_wakeup_arm_wake_irqs(void)
+{
+}
+
+static inline void device_wakeup_disarm_wake_irqs(void)
+{
+}
+
+#endif /* CONFIG_PM_SLEEP */
+
 /*
  * sysfs.c
  */
@@ -52,6 +92,14 @@ static inline void wakeup_sysfs_remove(struct device *dev) {}
 static inline int pm_qos_sysfs_add(struct device *dev) { return 0; }
 static inline void pm_qos_sysfs_remove(struct device *dev) {}
 
+static inline void dev_pm_arm_wake_irq(struct wake_irq *wirq)
+{
+}
+
+static inline void dev_pm_disarm_wake_irq(struct wake_irq *wirq)
+{
+}
+
 #endif
 
 #ifdef CONFIG_PM_SLEEP

diff --git a/drivers/base/power/runtime.c b/drivers/base/power/runtime.c
@@ -10,6 +10,7 @@
 #include <linux/sched.h>
 #include <linux/export.h>
 #include <linux/pm_runtime.h>
+#include <linux/pm_wakeirq.h>
 #include <trace/events/rpm.h>
 #include "power.h"
 
@@ -514,6 +515,7 @@ static int rpm_suspend(struct device *dev, int rpmflags)
 
 	callback = RPM_GET_CALLBACK(dev, runtime_suspend);
 
+	dev_pm_enable_wake_irq(dev);
 	retval = rpm_callback(callback, dev);
 	if (retval)
 		goto fail;
@@ -552,6 +554,7 @@ static int rpm_suspend(struct device *dev, int rpmflags)
 	return retval;
 
  fail:
+	dev_pm_disable_wake_irq(dev);
 	__update_runtime_status(dev, RPM_ACTIVE);
 	dev->power.deferred_resume = false;
 	wake_up_all(&dev->power.wait_queue);
@@ -734,13 +737,16 @@ static int rpm_resume(struct device *dev, int rpmflags)
 
 	callback = RPM_GET_CALLBACK(dev, runtime_resume);
 
+	dev_pm_disable_wake_irq(dev);
 	retval = rpm_callback(callback, dev);
 	if (retval) {
 		__update_runtime_status(dev, RPM_SUSPENDED);
 		pm_runtime_cancel_pending(dev);
+		dev_pm_enable_wake_irq(dev);
 	} else {
  no_callback:
 		__update_runtime_status(dev, RPM_ACTIVE);
+		pm_runtime_mark_last_busy(dev);
 		if (parent)
 			atomic_inc(&parent->power.child_count);
 	}