Added Arduino 101

arduino/arduino.ino

@@ -3,11 +3,11 @@
 
 #include <Adafruit_NeoPixel.h>
 #ifdef __AVR__
-  #include <avr/power.h>
+#include <avr/power.h>
 #endif
 
 // Which pin on the Arduino is connected to the NeoPixels
-#define PIN            5
+#define PIN            9
 
 // How many NeoPixels are attached to the Arduino?
 #define NUMPIXELS      39
@@ -32,25 +32,25 @@ void setup() {
 
   Serial.begin(BAUD);
   // This is for Trinket 5V 16MHz, you can remove these three lines if you are not using a Trinket
-  #if defined (__AVR_ATtiny85__)
-    if (F_CPU == 16000000) clock_prescale_set(clock_div_1);
-  #endif
-// End of trinket special code
+#if defined (__AVR_ATtiny85__)
+  if (F_CPU == 16000000) clock_prescale_set(clock_div_1);
+#endif
+  // End of trinket special code
 
   pixels.begin(); // This initializes the NeoPixel library.
 }
 
 void loop() {
 
- /* red = promptInt("r?");
-  green = promptInt("g?");
-  blue = promptInt("b?");
-*/
+  /* red = promptInt("r?");
+    green = promptInt("g?");
+    blue = promptInt("b?");
+  */
 
-  while(Serial.available()==0) //Wait for user input or serial port to initialize
+  while (Serial.available() == 0) //Wait for user input or serial port to initialize
   {
-
-   } 
+    //I should probaly move this to setup and make it a negative but it works so whatever
+  }
 
   red = Serial.readStringUntil(',').toInt();
   Serial.read(); //next character is comma, so skip it using this
@@ -61,47 +61,47 @@ void loop() {
   red = checkBounds(red);
   green = checkBounds(green);
   blue = checkBounds(blue);
-
 
-    //parse your data here. example:
-    //double x = Double.parseDouble(first);
+
+  //parse your data here. example:
+  //double x = Double.parseDouble(first);
   ardprintf("\n\nDone, set %d, %d, %d \n\n\n", red, green, blue);
 
   // For a set of NeoPixels the first NeoPixel is 0, second is 1, all the way up to the count of pixels minus one.
 
-  for(int i=0;i<NUMPIXELS;i++){
+  for (int i = 0; i < NUMPIXELS; i++) {
     // pixels.Color takes RGB values, from 0,0,0 up to 255,255,255
-    pixels.setPixelColor(i, pixels.Color(red,green,blue)); // Moderately bright green color.
+    pixels.setPixelColor(i, pixels.Color(red, green, blue)); // Moderately bright green color.
 
     pixels.show(); // This sends the updated pixel color to the hardware.
 
     delay(delayval); // Delay for a period of time (in milliseconds).
   }
 }
 
-int checkBounds(int val){
-  if(val > maxBrightness){
-       val = maxBrightness;
-   }
+int checkBounds(int val) {
+  if (val > maxBrightness) {
+    val = maxBrightness;
+  }
 
-   if(val < 0){
-      val = 0;
-   }
+  if (val < 0) {
+    val = 0;
+  }
 
-   return val; //Return a parsed integer
+  return val; //Return a parsed integer
 }
 
-int promptInt(String prompt){
+int promptInt(String prompt) {
   int val;
   Serial.println(prompt);
-
-
 
-   val = Serial.parseInt();
 
 
+  val = Serial.parseInt();
+
 
-} 
+
+}
 
 //The following function is bullshit to make sure I can actually print multiple variables in the same line. Aparently implementing prinf correnctly over serial was too much work for the core team....
 
@@ -113,45 +113,45 @@ int promptInt(String prompt){
 
 int ardprintf(char *str, ...)
 {
-  int i, count=0, j=0, flag=0;
-  char temp[ARDBUFFER+1];
-  for(i=0; str[i]!='\0';i++)  if(str[i]=='%')  count++;
+  int i, count = 0, j = 0, flag = 0;
+  char temp[ARDBUFFER + 1];
+  for (i = 0; str[i] != '\0'; i++)  if (str[i] == '%')  count++;
 
   va_list argv;
   va_start(argv, count);
-  for(i=0,j=0; str[i]!='\0';i++)
+  for (i = 0, j = 0; str[i] != '\0'; i++)
   {
-    if(str[i]=='%')
+    if (str[i] == '%')
     {
       temp[j] = '\0';
       Serial.print(temp);
-      j=0;
+      j = 0;
       temp[0] = '\0';
 
-      switch(str[++i])
+      switch (str[++i])
       {
         case 'd': Serial.print(va_arg(argv, int));
-                  break;
+          break;
         case 'l': Serial.print(va_arg(argv, long));
-                  break;
+          break;
         case 'f': Serial.print(va_arg(argv, double));
-                  break;
+          break;
         case 'c': Serial.print((char)va_arg(argv, int));
-                  break;
+          break;
         case 's': Serial.print(va_arg(argv, char *));
-                  break;
+          break;
         default:  ;
       };
     }
-    else 
+    else
     {
       temp[j] = str[i];
-      j = (j+1)%ARDBUFFER;
-      if(j==0) 
+      j = (j + 1) % ARDBUFFER;
+      if (j == 0)
       {
         temp[ARDBUFFER] = '\0';
         Serial.print(temp);
-        temp[0]='\0';
+        temp[0] = '\0';
       }
     }
   };