iommu: Replace device_lock() with group->mutex

device_lock() was used in iommu_group_store_type() to prevent the
devices in an iommu group from being attached by any device driver.
On the other hand, in order to avoid lock race between group->mutex
and device_lock(), it limited the usage scenario to the singleton
groups.

We already have the DMA ownership scheme to avoid driver attachment
and group->mutex ensures that device ops are always valid, there's
no need for device_lock() anymore. Remove device_lock() and the
singleton group limitation.

Signed-off-by: Lu Baolu <[email protected]>
Reviewed-by: Jason Gunthorpe <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Joerg Roedel <[email protected]>

drivers/iommu/iommu.c

@@ -2956,14 +2956,6 @@ static int iommu_change_dev_def_domain(struct iommu_group *group,
 		goto out;
 	}
 
-	/* We can bring up a flush queue without tearing down the domain */
-	if (type == IOMMU_DOMAIN_DMA_FQ && prev_dom->type == IOMMU_DOMAIN_DMA) {
-		ret = iommu_dma_init_fq(prev_dom);
-		if (!ret)
-			prev_dom->type = IOMMU_DOMAIN_DMA_FQ;
-		goto out;
-	}
-
 	/* Sets group->default_domain to the newly allocated domain */
 	ret = iommu_group_alloc_default_domain(dev->bus, group, type);
 	if (ret)
@@ -2996,7 +2988,7 @@ static int iommu_change_dev_def_domain(struct iommu_group *group,
  * transition. Return failure if this isn't met.
  *
  * We need to consider the race between this and the device release path.
- * device_lock(dev) is used here to guarantee that the device release path
+ * group->mutex is used here to guarantee that the device release path
  * will not be entered at the same time.
  */
 static ssize_t iommu_group_store_type(struct iommu_group *group,
@@ -3023,61 +3015,29 @@ static ssize_t iommu_group_store_type(struct iommu_group *group,
 	else
 		return -EINVAL;
 
-	/*
-	 * Lock/Unlock the group mutex here before device lock to
-	 * 1. Make sure that the iommu group has only one device (this is a
-	 *    prerequisite for step 2)
-	 * 2. Get struct *dev which is needed to lock device
-	 */
 	mutex_lock(&group->mutex);
-	if (iommu_group_device_count(group) != 1) {
+	/* We can bring up a flush queue without tearing down the domain. */
+	if (req_type == IOMMU_DOMAIN_DMA_FQ &&
+	    group->default_domain->type == IOMMU_DOMAIN_DMA) {
+		ret = iommu_dma_init_fq(group->default_domain);
+		if (!ret)
+			group->default_domain->type = IOMMU_DOMAIN_DMA_FQ;
 		mutex_unlock(&group->mutex);
-		pr_err_ratelimited("Cannot change default domain: Group has more than one device\n");
-		return -EINVAL;
+
+		return ret ?: count;
+	}
+
+	/* Otherwise, ensure that device exists and no driver is bound. */
+	if (list_empty(&group->devices) || group->owner_cnt) {
+		mutex_unlock(&group->mutex);
+		return -EPERM;
 	}
 
-	/* Since group has only one device */
 	grp_dev = list_first_entry(&group->devices, struct group_device, list);
 	dev = grp_dev->dev;
-	get_device(dev);
 
-	/*
-	 * Don't hold the group mutex because taking group mutex first and then
-	 * the device lock could potentially cause a deadlock as below. Assume
-	 * two threads T1 and T2. T1 is trying to change default domain of an
-	 * iommu group and T2 is trying to hot unplug a device or release [1] VF
-	 * of a PCIe device which is in the same iommu group. T1 takes group
-	 * mutex and before it could take device lock assume T2 has taken device
-	 * lock and is yet to take group mutex. Now, both the threads will be
-	 * waiting for the other thread to release lock. Below, lock order was
-	 * suggested.
-	 * device_lock(dev);
-	 *	mutex_lock(&group->mutex);
-	 *		iommu_change_dev_def_domain();
-	 *	mutex_unlock(&group->mutex);
-	 * device_unlock(dev);
-	 *
-	 * [1] Typical device release path
-	 * device_lock() from device/driver core code
-	 *  -> bus_notifier()
-	 *   -> iommu_bus_notifier()
-	 *    -> iommu_release_device()
-	 *     -> ops->release_device() vendor driver calls back iommu core code
-	 *      -> mutex_lock() from iommu core code
-	 */
-	mutex_unlock(&group->mutex);
-
-	/* Check if the device in the group still has a driver bound to it */
-	device_lock(dev);
-	if (device_is_bound(dev) && !(req_type == IOMMU_DOMAIN_DMA_FQ &&
-	    group->default_domain->type == IOMMU_DOMAIN_DMA)) {
-		pr_err_ratelimited("Device is still bound to driver\n");
-		ret = -EBUSY;
-		goto out;
-	}
-
-	mutex_lock(&group->mutex);
 	ret = iommu_change_dev_def_domain(group, dev, req_type);
+
 	/*
 	 * Release the mutex here because ops->probe_finalize() call-back of
 	 * some vendor IOMMU drivers calls arm_iommu_attach_device() which
@@ -3088,14 +3048,9 @@ static ssize_t iommu_group_store_type(struct iommu_group *group,
 
 	/* Make sure dma_ops is appropriatley set */
 	if (!ret)
-		iommu_group_do_probe_finalize(dev, group->default_domain);
-	ret = ret ?: count;
-
-out:
-	device_unlock(dev);
-	put_device(dev);
+		__iommu_group_dma_finalize(group);
 
-	return ret;
+	return ret ?: count;
 }
 
 static bool iommu_is_default_domain(struct iommu_group *group)