Merge tag 'tags/cleanup2-3.15' of git://git.kernel.org/pub/scm/linux/…

…kernel/git/arm/arm-soc

Pull ARM SoC late cleanups from Arnd Bergmann:
 "These could not be part of the first cleanup branch, because they
  either came too late in the cycle, or they have dependencies on other
  branches.  Important changes are:

   - The integrator platform is almost multiplatform capable after some
     reorganization (Linus Walleij)
   - Minor cleanups on Zynq (Michal Simek)
   - Lots of changes for Exynos and other Samsung platforms, including
     further preparations for multiplatform support and the clocks
     bindings are rearranged"

* tag 'tags/cleanup2-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
  devicetree: fix newly added exynos sata bindings
  ARM: EXYNOS: Fix compilation error in cpuidle.c
  ARM: S5P64X0: Explicitly include linux/serial_s3c.h in mach/pm-core.h
  ARM: EXYNOS: Remove hardware.h file
  ARM: SAMSUNG: Remove hardware.h inclusion
  ARM: S3C24XX: Remove invalid code from hardware.h
  dt-bindings: clock: Move exynos-audss-clk.h to dt-bindings/clock
  ARM: dts: Keep some essential LDOs enabled for arndale-octa board
  ARM: dts: Disable MDMA1 node for arndale-octa board
  ARM: S3C64XX: Fix build for implicit serial_s3c.h inclusion
  serial: s3c: Fix build of header without serial_core.h preinclusion
  ARM: EXYNOS: Allow wake-up using GIC interrupts
  ARM: EXYNOS: Stop using legacy Samsung PM code
  ARM: EXYNOS: Remove PM initcalls and useless indirection
  ARM: EXYNOS: Fix abuse of CONFIG_PM
  ARM: SAMSUNG: Move s3c_pm_check_* prototypes to plat/pm-common.h
  ARM: SAMSUNG: Move common save/restore helpers to separate file
  ARM: SAMSUNG: Move Samsung PM debug code into separate file
  ARM: SAMSUNG: Consolidate PM debug functions
  ARM: SAMSUNG: Use debug_ll_addr() to get UART base address
  ...

Documentation/devicetree/bindings/ata/exynos-sata.txt

@@ -4,14 +4,27 @@ SATA nodes are defined to describe on-chip Serial ATA controllers.
 Each SATA controller should have its own node.
 
 Required properties:
-- compatible        : compatible list, contains "samsung,exynos5-sata"
-- interrupts        : <interrupt mapping for SATA IRQ>
-- reg               : <registers mapping>
-- samsung,sata-freq : <frequency in MHz>
+- compatible		: compatible list, contains "samsung,exynos5-sata"
+- interrupts		: <interrupt mapping for SATA IRQ>
+- reg			: <registers mapping>
+- samsung,sata-freq	: <frequency in MHz>
+- phys			: Must contain exactly one entry as specified
+			  in phy-bindings.txt
+- phy-names		: Must be "sata-phy"
+
+Optional properties:
+- clocks		: Must contain an entry for each entry in clock-names.
+- clock-names		: Shall be "sata" for the external SATA bus clock,
+			  and "sclk_sata" for the internal controller clock.
 
 Example:
-        sata@ffe08000 {
-                compatible = "samsung,exynos5-sata";
-                reg = <0xffe08000 0x1000>;
-                interrupts = <115>;
-        };
+	sata@122f0000 {
+		compatible = "snps,dwc-ahci";
+		samsung,sata-freq = <66>;
+		reg = <0x122f0000 0x1ff>;
+		interrupts = <0 115 0>;
+		clocks = <&clock 277>, <&clock 143>;
+		clock-names = "sata", "sclk_sata";
+		phys = <&sata_phy>;
+		phy-names = "sata-phy";
+	};

Documentation/devicetree/bindings/clock/zynq-7000.txt

@@ -14,6 +14,7 @@ for all clock consumers of PS clocks.
 Required properties:
  - #clock-cells : Must be 1
  - compatible : "xlnx,ps7-clkc"
+ - reg : SLCR offset and size taken via syscon < 0x100 0x100 >
  - ps-clk-frequency : Frequency of the oscillator providing ps_clk in HZ
 		      (usually 33 MHz oscillators are used for Zynq platforms)
  - clock-output-names : List of strings used to name the clock outputs. Shall be
@@ -87,10 +88,11 @@ Clock outputs:
  47: dbg_apb
 
 Example:
-	clkc: clkc {
+	clkc: clkc@100 {
 		#clock-cells = <1>;
 		compatible = "xlnx,ps7-clkc";
 		ps-clk-frequency = <33333333>;
+		reg = <0x100 0x100>;
 		clock-output-names = "armpll", "ddrpll", "iopll", "cpu_6or4x",
 				"cpu_3or2x", "cpu_2x", "cpu_1x", "ddr2x", "ddr3x",
 				"dci", "lqspi", "smc", "pcap", "gem0", "gem1",

Documentation/devicetree/bindings/phy/samsung-phy.txt

@@ -74,3 +74,43 @@ phy-consumer@12340000 {
 
 Refer to DT bindings documentation of particular PHY consumer devices for more
 information about required PHYs and the way of specification.
+
+Samsung SATA PHY Controller
+---------------------------
+
+SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers.
+Each SATA PHY controller should have its own node.
+
+Required properties:
+- compatible        : compatible list, contains "samsung,exynos5250-sata-phy"
+- reg : offset and length of the SATA PHY register set;
+- #phy-cells : must be zero
+- clocks : must be exactly one entry
+- clock-names : must be "sata_phyctrl"
+- samsung,exynos-sataphy-i2c-phandle : a phandle to the I2C device, no arguments
+- samsung,syscon-phandle : a phandle to the PMU system controller, no arguments
+
+Example:
+	sata_phy: sata-phy@12170000 {
+		compatible = "samsung,exynos5250-sata-phy";
+		reg = <0x12170000 0x1ff>;
+		clocks = <&clock 287>;
+		clock-names = "sata_phyctrl";
+		#phy-cells = <0>;
+		samsung,exynos-sataphy-i2c-phandle = <&sata_phy_i2c>;
+		samsung,syscon-phandle = <&pmu_syscon>;
+	};
+
+Device-Tree bindings for sataphy i2c client driver
+--------------------------------------------------
+
+Required properties:
+compatible: Should be "samsung,exynos-sataphy-i2c"
+- reg: I2C address of the sataphy i2c device.
+
+Example:
+
+	sata_phy_i2c:sata-phy@38 {
+		compatible = "samsung,exynos-sataphy-i2c";
+		reg = <0x38>;
+	};

arch/arm/Kconfig.debug

@@ -1141,7 +1141,7 @@ config DEBUG_UART_8250_FLOW_CONTROL
 
 config DEBUG_UNCOMPRESS
 	bool
-	depends on ARCH_MULTIPLATFORM || ARCH_MSM || ARCH_EXYNOS
+	depends on ARCH_MULTIPLATFORM || ARCH_MSM || PLAT_SAMSUNG
 	default y if DEBUG_LL && !DEBUG_OMAP2PLUS_UART && \
 		     (!DEBUG_TEGRA_UART || !ZBOOT_ROM)
 	help
@@ -1158,7 +1158,7 @@ config DEBUG_UNCOMPRESS
 config UNCOMPRESS_INCLUDE
 	string
 	default "debug/uncompress.h" if ARCH_MULTIPLATFORM || ARCH_MSM || \
-					ARCH_EXYNOS || ARCH_EFM32
+					PLAT_SAMSUNG || ARCH_EFM32
 	default "mach/uncompress.h"
 
 config EARLY_PRINTK

arch/arm/boot/dts/exynos4.dtsi

@@ -86,6 +86,11 @@
 		reg = <0x10023CE0 0x20>;
 	};
 
+	pd_gps_alive: gps-alive-power-domain@10023D00 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x10023D00 0x20>;
+	};
+
 	gic: interrupt-controller@10490000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;

arch/arm/boot/dts/exynos4210-origen.dts

@@ -19,7 +19,7 @@
 
 / {
 	model = "Insignal Origen evaluation board based on Exynos4210";
-	compatible = "insignal,origen", "samsung,exynos4210";
+	compatible = "insignal,origen", "samsung,exynos4210", "samsung,exynos4";
 
 	memory {
 		reg = <0x40000000 0x10000000

arch/arm/boot/dts/exynos4210-smdkv310.dts

@@ -19,7 +19,7 @@
 
 / {
 	model = "Samsung smdkv310 evaluation board based on Exynos4210";
-	compatible = "samsung,smdkv310", "samsung,exynos4210";
+	compatible = "samsung,smdkv310", "samsung,exynos4210", "samsung,exynos4";
 
 	memory {
 		reg = <0x40000000 0x80000000>;

arch/arm/boot/dts/exynos4210-trats.dts

@@ -17,7 +17,7 @@
 
 / {
 	model = "Samsung Trats based on Exynos4210";
-	compatible = "samsung,trats", "samsung,exynos4210";
+	compatible = "samsung,trats", "samsung,exynos4210", "samsung,exynos4";
 
 	memory {
 		reg =  <0x40000000 0x10000000

arch/arm/boot/dts/exynos4210-universal_c210.dts

@@ -17,7 +17,7 @@
 
 / {
 	model = "Samsung Universal C210 based on Exynos4210 rev0";
-	compatible = "samsung,universal_c210", "samsung,exynos4210";
+	compatible = "samsung,universal_c210", "samsung,exynos4210", "samsung,exynos4";
 
 	memory {
 		reg =  <0x40000000 0x10000000

arch/arm/boot/dts/exynos4210.dtsi

@@ -23,7 +23,7 @@
 #include "exynos4210-pinctrl.dtsi"
 
 / {
-	compatible = "samsung,exynos4210";
+	compatible = "samsung,exynos4210", "samsung,exynos4";
 
 	aliases {
 		pinctrl0 = &pinctrl_0;

arch/arm/boot/dts/exynos4212.dtsi

@@ -20,18 +20,13 @@
 #include "exynos4x12.dtsi"
 
 / {
-	compatible = "samsung,exynos4212";
+	compatible = "samsung,exynos4212", "samsung,exynos4";
 
-	gic: interrupt-controller@10490000 {
-		cpu-offset = <0x8000>;
+	combiner: interrupt-controller@10440000 {
+		samsung,combiner-nr = <18>;
 	};
 
-	interrupt-controller@10440000 {
-		samsung,combiner-nr = <18>;
-		interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
-			     <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
-			     <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
-			     <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>,
-			     <0 107 0>, <0 108 0>;
+	gic: interrupt-controller@10490000 {
+		cpu-offset = <0x8000>;
 	};
 };

arch/arm/boot/dts/exynos4412-odroidx.dts

@@ -16,7 +16,7 @@
 
 / {
 	model = "Hardkernel ODROID-X board based on Exynos4412";
-	compatible = "hardkernel,odroid-x", "samsung,exynos4412";
+	compatible = "hardkernel,odroid-x", "samsung,exynos4412", "samsung,exynos4";
 
 	memory {
 		reg = <0x40000000 0x40000000>;

arch/arm/boot/dts/exynos4412-origen.dts

@@ -17,7 +17,7 @@
 
 / {
 	model = "Insignal Origen evaluation board based on Exynos4412";
-	compatible = "insignal,origen4412", "samsung,exynos4412";
+	compatible = "insignal,origen4412", "samsung,exynos4412", "samsung,exynos4";
 
 	memory {
 		reg = <0x40000000 0x40000000>;

arch/arm/boot/dts/exynos4412-smdk4412.dts

@@ -17,7 +17,7 @@
 
 / {
 	model = "Samsung SMDK evaluation board based on Exynos4412";
-	compatible = "samsung,smdk4412", "samsung,exynos4412";
+	compatible = "samsung,smdk4412", "samsung,exynos4412", "samsung,exynos4";
 
 	memory {
 		reg = <0x40000000 0x40000000>;

arch/arm/boot/dts/exynos4412-tiny4412.dts

@@ -16,7 +16,7 @@
 
 / {
 	model = "FriendlyARM TINY4412 board based on Exynos4412";
-	compatible = "friendlyarm,tiny4412", "samsung,exynos4412";
+	compatible = "friendlyarm,tiny4412", "samsung,exynos4412", "samsung,exynos4";
 
 	memory {
 		reg = <0x40000000 0x40000000>;

arch/arm/boot/dts/exynos4412-trats2.dts

@@ -17,7 +17,7 @@
 
 / {
 	model = "Samsung Trats 2 based on Exynos4412";
-	compatible = "samsung,trats2", "samsung,exynos4412";
+	compatible = "samsung,trats2", "samsung,exynos4412", "samsung,exynos4";
 
 	aliases {
 		i2c8 = &i2c_ak8975;
@@ -106,6 +106,11 @@
 		};
 	};
 
+	adc: adc@126C0000 {
+		vdd-supply = <&ldo3_reg>;
+		status = "okay";
+	};
+
 	i2c@13890000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-slave-addr = <0x10>;
@@ -589,4 +594,20 @@
 			};
 		};
 	};
+
+	thermistor-ap@0 {
+		compatible = "ntc,ncp15wb473";
+		pullup-uv = <1800000>;	 /* VCC_1.8V_AP */
+		pullup-ohm = <100000>;	 /* 100K */
+		pulldown-ohm = <100000>; /* 100K */
+		io-channels = <&adc 1>;  /* AP temperature */
+	};
+
+	thermistor-battery@1 {
+		compatible = "ntc,ncp15wb473";
+		pullup-uv = <1800000>;	 /* VCC_1.8V_AP */
+		pullup-ohm = <100000>;	 /* 100K */
+		pulldown-ohm = <100000>; /* 100K */
+		io-channels = <&adc 2>;  /* Battery temperature */
+	};
 };

arch/arm/boot/dts/exynos4412.dtsi

@@ -20,19 +20,13 @@
 #include "exynos4x12.dtsi"
 
 / {
-	compatible = "samsung,exynos4412";
+	compatible = "samsung,exynos4412", "samsung,exynos4";
 
-	gic: interrupt-controller@10490000 {
-		cpu-offset = <0x4000>;
-	};
-
-	interrupt-controller@10440000 {
+	combiner: interrupt-controller@10440000 {
 		samsung,combiner-nr = <20>;
-		interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
-			     <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
-			     <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
-			     <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>,
-			     <0 107 0>, <0 108 0>, <0 48 0>, <0 42 0>;
 	};
 
+	gic: interrupt-controller@10490000 {
+		cpu-offset = <0x4000>;
+	};
 };

arch/arm/boot/dts/exynos4x12.dtsi

@@ -31,6 +31,12 @@
 		mshc0 = &mshc_0;
 	};
 
+	pmu {
+		compatible = "arm,cortex-a9-pmu";
+		interrupt-parent = <&combiner>;
+		interrupts = <2 2>, <3 2>, <18 2>, <19 2>;
+	};
+
 	pd_isp: isp-power-domain@10023CA0 {
 		compatible = "samsung,exynos4210-pd";
 		reg = <0x10023CA0 0x20>;
@@ -62,6 +68,14 @@
 		};
 	};
 
+	combiner: interrupt-controller@10440000 {
+		interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
+			     <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
+			     <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
+			     <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>,
+			     <0 107 0>, <0 108 0>, <0 48 0>, <0 42 0>;
+	};
+
 	pinctrl_0: pinctrl@11400000 {
 		compatible = "samsung,exynos4x12-pinctrl";
 		reg = <0x11400000 0x1000>;
@@ -80,6 +94,18 @@
 		};
 	};
 
+	adc: adc@126C0000 {
+		compatible = "samsung,exynos-adc-v1";
+		reg = <0x126C0000 0x100>, <0x10020718 0x4>;
+		interrupt-parent = <&combiner>;
+		interrupts = <10 3>;
+		clocks = <&clock CLK_TSADC>;
+		clock-names = "adc";
+		#io-channel-cells = <1>;
+		io-channel-ranges;
+		status = "disabled";
+	};
+
 	pinctrl_2: pinctrl@03860000 {
 		compatible = "samsung,exynos4x12-pinctrl";
 		reg = <0x03860000 0x1000>;