pch_uart: reference clock on CM-iTC

Default clock source for UARTs on Topcliff is external UART_CLK. On CM-iTC USB_48MHz is used instead. After VCO2PLL and DIV manipulations UARTs will receive 192 MHz. Clock manipulations on Topcliff are controlled in pch_phub.c v2: redone against the linux-next tree v3: redone against linux/kernel/git/next/linux-next.git snapshot Signed-off-by: Denis Turischev <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
akeromi · Mar 14, 2011 · 6ae705b · 6ae705b
1 parent 1a738dc
commit 6ae705b
Show file tree

Hide file tree

Showing 2 changed files with 23 additions and 2 deletions.
diff --git a/drivers/misc/pch_phub.c b/drivers/misc/pch_phub.c
@@ -27,6 +27,7 @@
 #include <linux/mutex.h>
 #include <linux/if_ether.h>
 #include <linux/ctype.h>
+#include <linux/dmi.h>
 
 #define PHUB_STATUS 0x00		/* Status Register offset */
 #define PHUB_CONTROL 0x04		/* Control Register offset */
@@ -46,6 +47,13 @@
 #define PCH_MINOR_NOS 1
 #define CLKCFG_CAN_50MHZ 0x12000000
 #define CLKCFG_CANCLK_MASK 0xFF000000
+#define CLKCFG_UART_MASK			0xFFFFFF
+
+/* CM-iTC */
+#define CLKCFG_UART_48MHZ			(1 << 16)
+#define CLKCFG_BAUDDIV				(2 << 20)
+#define CLKCFG_PLL2VCO				(8 << 9)
+#define CLKCFG_UARTCLKSEL			(1 << 18)
 
 /* Macros for ML7213 */
 #define PCI_VENDOR_ID_ROHM			0x10db
@@ -618,6 +626,14 @@ static int __devinit pch_phub_probe(struct pci_dev *pdev,
 					       CLKCFG_CAN_50MHZ,
 					       CLKCFG_CANCLK_MASK);
 
+		/* quirk for CM-iTC board */
+		if (strstr(dmi_get_system_info(DMI_BOARD_NAME), "CM-iTC"))
+			pch_phub_read_modify_write_reg(chip,
+						(unsigned int)CLKCFG_REG_OFFSET,
+						CLKCFG_UART_48MHZ | CLKCFG_BAUDDIV |
+						CLKCFG_PLL2VCO | CLKCFG_UARTCLKSEL,
+						CLKCFG_UART_MASK);
+
 		/* set the prefech value */
 		iowrite32(0x000affaa, chip->pch_phub_base_address + 0x14);
 		/* set the interrupt delay value */

diff --git a/drivers/tty/serial/pch_uart.c b/drivers/tty/serial/pch_uart.c
@@ -21,6 +21,7 @@
 #include <linux/serial_core.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
+#include <linux/dmi.h>
 
 #include <linux/dmaengine.h>
 #include <linux/pch_dma.h>
@@ -1404,14 +1405,18 @@ static struct eg20t_port *pch_uart_init_port(struct pci_dev *pdev,
 	if (!rxbuf)
 		goto init_port_free_txbuf;
 
+	base_baud = 1843200; /* 1.8432MHz */
+
+	/* quirk for CM-iTC board */
+	if (strstr(dmi_get_system_info(DMI_BOARD_NAME), "CM-iTC"))
+		base_baud = 192000000; /* 192.0MHz */
+
 	switch (port_type) {
 	case PORT_UNKNOWN:
 		fifosize = 256; /* EG20T/ML7213: UART0 */
-		base_baud = 1843200; /* 1.8432MHz */
 		break;
 	case PORT_8250:
 		fifosize = 64; /* EG20T:UART1~3  ML7213: UART1~2*/
-		base_baud = 1843200; /* 1.8432MHz */
 		break;
 	default:
 		dev_err(&pdev->dev, "Invalid Port Type(=%d)\n", port_type);