scsi: isci: initialize shost fully before calling scsi_add_host()

[ Upstream commit cc29a1b0a3f2597ce887d339222fa85b9307706d ]

scsi_mq_setup_tags(), which is called by scsi_add_host(), calculates the
command size to allocate based on the prot_capabilities. In the isci
driver, scsi_host_set_prot() is called after scsi_add_host() so the command
size gets calculated to be smaller than it needs to be.  Eventually,
scsi_mq_init_request() locates the 'prot_sdb' after the command assuming it
was sized correctly and a buffer overrun may occur.

However, seeing blk_mq_alloc_rqs() rounds up to the nearest cache line
size, the mistake can go unnoticed.

The bug was noticed after the struct request size was reduced by commit
9d037ad707ed ("block: remove req->timeout_list")

Which likely reduced the allocated space for the request by an entire cache
line, enough that the overflow could be hit and it caused a panic, on boot,
at:

  RIP: 0010:t10_pi_complete+0x77/0x1c0
  Call Trace:
    <IRQ>
    sd_done+0xf5/0x340
    scsi_finish_command+0xc3/0x120
    blk_done_softirq+0x83/0xb0
    __do_softirq+0xa1/0x2e6
    irq_exit+0xbc/0xd0
    call_function_single_interrupt+0xf/0x20
    </IRQ>

sd_done() would call scsi_prot_sg_count() which reads the number of
entities in 'prot_sdb', but seeing 'prot_sdb' is located after the end of
the allocated space it reads a garbage number and erroneously calls
t10_pi_complete().

To prevent this, the calls to scsi_host_set_prot() are moved into
isci_host_alloc() before the call to scsi_add_host(). Out of caution, also
move the similar call to scsi_host_set_guard().

Fixes: 3d2d752 ("[SCSI] isci: T10 DIF support")
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Logan Gunthorpe <[email protected]>
Cc: Intel SCU Linux support <[email protected]>
Cc: Artur Paszkiewicz <[email protected]>
Cc: "James E.J. Bottomley" <[email protected]>
Cc: "Martin K. Petersen" <[email protected]>
Cc: Christoph Hellwig <[email protected]>
Cc: Jens Axboe <[email protected]>
Cc: Jeff Moyer <[email protected]>
Reviewed-by: Jeff Moyer <[email protected]>
Reviewed-by: Jens Axboe <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>

drivers/scsi/isci/init.c

@@ -588,6 +588,13 @@ static struct isci_host *isci_host_alloc(struct pci_dev *pdev, int id)
 	shost->max_lun = ~0;
 	shost->max_cmd_len = MAX_COMMAND_SIZE;
 
+	/* turn on DIF support */
+	scsi_host_set_prot(shost,
+			   SHOST_DIF_TYPE1_PROTECTION |
+			   SHOST_DIF_TYPE2_PROTECTION |
+			   SHOST_DIF_TYPE3_PROTECTION);
+	scsi_host_set_guard(shost, SHOST_DIX_GUARD_CRC);
+
 	err = scsi_add_host(shost, &pdev->dev);
 	if (err)
 		goto err_shost;
@@ -675,13 +682,6 @@ static int isci_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 			goto err_host_alloc;
 		}
 		pci_info->hosts[i] = h;
-
-		/* turn on DIF support */
-		scsi_host_set_prot(to_shost(h),
-				   SHOST_DIF_TYPE1_PROTECTION |
-				   SHOST_DIF_TYPE2_PROTECTION |
-				   SHOST_DIF_TYPE3_PROTECTION);
-		scsi_host_set_guard(to_shost(h), SHOST_DIX_GUARD_CRC);
 	}
 
 	err = isci_setup_interrupts(pdev);