Merge git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-wat…

…chdog

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] wdt_pci.c: remove #ifdef CONFIG_WDT_501_PCI
  [WATCHDOG] hpwdt: Add NMI priority option
  [WATCHDOG] OMAP fixes: enable clock in probe, trigger timer reload
  [WATCHDOG] add bcm47xx watchdog driver
  [WATCHDOG] Freescale STMP: watchdog driver
  [WATCHDOG] twl4030 watchdog driver
  [WATCHDOG] U300 COH 901 327 watchdog driver
  [WATCHDOG] Add pnx833x_wdt

Documentation/watchdog/hpwdt.txt

@@ -19,30 +19,41 @@ Last reviewed: 06/02/2009
  not be updated in a timely fashion and a hardware system reset (also known as
  an Automatic Server Recovery (ASR)) event will occur.
 
- The hpwdt driver also has three (3) module parameters. They are the following:
+ The hpwdt driver also has four (4) module parameters. They are the following:
 
  soft_margin - allows the user to set the watchdog timer value
  allow_kdump - allows the user to save off a kernel dump image after an NMI
  nowayout    - basic watchdog parameter that does not allow the timer to
                be restarted or an impending ASR to be escaped.
+ priority    - determines whether or not the hpwdt driver is first on the
+               die_notify list to handle NMIs or last. The default value
+               for this module parameter is 0 or LAST. If the user wants to
+               enable NMI sourcing then reload the hpwdt driver with
+               priority=1 (and boot with nmi_watchdog=0).
 
  NOTE: More information about watchdog drivers in general, including the ioctl
        interface to /dev/watchdog can be found in
        Documentation/watchdog/watchdog-api.txt and Documentation/IPMI.txt.
 
- The NMI sourcing capability is disabled when the driver discovers that the
- nmi_watchdog is turned on (nmi_watchdog = 1). This is due to the inability to
+ The priority parameter was introduced due to other kernel software that relied
+ on handling NMIs (like oprofile). Keeping hpwdt's priority at 0 (or LAST)
+ enables the users of NMIs for non critical events to be work as expected.
+
+ The NMI sourcing capability is disabled by default due to the inability to
  distinguish between "NMI Watchdog Ticks" and "HW generated NMI events" in the
  Linux kernel. What this means is that the hpwdt nmi handler code is called
  each time the NMI signal fires off. This could amount to several thousands of
  NMIs in a matter of seconds. If a user sees the Linux kernel's "dazed and
  confused" message in the logs or if the system gets into a hung state, then
- the user should reboot with nmi_watchdog=0.
+ the hpwdt driver can be reloaded with the "priority" module parameter set
+ (priority=1).
 
  1. If the kernel has not been booted with nmi_watchdog turned off then
     edit /boot/grub/menu.lst and place the nmi_watchdog=0 at the end of the
     currently booting kernel line.
  2. reboot the sever
+ 3. Once the system comes up perform a rmmod hpwdt
+ 4. insmod /lib/modules/`uname -r`/kernel/drivers/char/watchdog/hpwdt.ko priority=1
 
  Now, the hpwdt can successfully receive and source the NMI and provide a log
  message that details the reason for the NMI (as determined by the HP BIOS).

drivers/mfd/twl4030-core.c

@@ -101,6 +101,12 @@
 #define twl_has_usb()	false
 #endif
 
+#if defined(CONFIG_TWL4030_WATCHDOG) || \
+	defined(CONFIG_TWL4030_WATCHDOG_MODULE)
+#define twl_has_watchdog()        true
+#else
+#define twl_has_watchdog()        false
+#endif
 
 /* Triton Core internal information (BEGIN) */
 
@@ -526,6 +532,12 @@ add_children(struct twl4030_platform_data *pdata, unsigned long features)
 		usb_transceiver = child;
 	}
 
+	if (twl_has_watchdog()) {
+		child = add_child(0, "twl4030_wdt", NULL, 0, false, 0, 0);
+		if (IS_ERR(child))
+			return PTR_ERR(child);
+	}
+
 	if (twl_has_regulator()) {
 		/*
 		child = add_regulator(TWL4030_REG_VPLL1, pdata->vpll1);

drivers/watchdog/Kconfig

@@ -240,6 +240,32 @@ config ORION_WATCHDOG
 	  To compile this driver as a module, choose M here: the
 	  module will be called orion_wdt.
 
+config COH901327_WATCHDOG
+	bool "ST-Ericsson COH 901 327 watchdog"
+	depends on ARCH_U300
+	default y if MACH_U300
+	help
+	  Say Y here to include Watchdog timer support for the
+	  watchdog embedded into the ST-Ericsson U300 series platforms.
+	  This watchdog is used to reset the system and thus cannot be
+	  compiled as a module.
+
+config TWL4030_WATCHDOG
+	tristate "TWL4030 Watchdog"
+	depends on TWL4030_CORE
+	help
+	  Support for TI TWL4030 watchdog.  Say 'Y' here to enable the
+	  watchdog timer support for TWL4030 chips.
+
+config STMP3XXX_WATCHDOG
+	tristate "Freescale STMP3XXX watchdog"
+	depends on ARCH_STMP3XXX
+	help
+	  Say Y here if to include support for the watchdog timer
+	  for the Sigmatel STMP37XX/378X SoC.
+	  To compile this driver as a module, choose M here: the
+	  module will be called stmp3xxx_wdt.
+
 # AVR32 Architecture
 
 config AT32AP700X_WDT
@@ -703,6 +729,12 @@ config SBC_EPX_C3_WATCHDOG
 
 # MIPS Architecture
 
+config BCM47XX_WDT
+	tristate "Broadcom BCM47xx Watchdog Timer"
+	depends on BCM47XX
+	help
+	  Hardware driver for the Broadcom BCM47xx Watchog Timer.
+
 config RC32434_WDT
 	tristate "IDT RC32434 SoC Watchdog Timer"
 	depends on MIKROTIK_RB532
@@ -729,6 +761,15 @@ config WDT_MTX1
 	  Hardware driver for the MTX-1 boards. This is a watchdog timer that
 	  will reboot the machine after a 100 seconds timer expired.
 
+config PNX833X_WDT
+	tristate "PNX833x Hardware Watchdog"
+	depends on SOC_PNX8335
+	help
+	  Hardware driver for the PNX833x's watchdog. This is a
+	  watchdog timer that will reboot the machine after a programable
+	  timer has expired and no process has written to /dev/watchdog during
+	  that time.
+
 config WDT_RM9K_GPI
 	tristate "RM9000/GPI hardware watchdog"
 	depends on CPU_RM9000
@@ -966,24 +1007,16 @@ config WDTPCI
 	---help---
 	  If you have a PCI-WDT500/501 watchdog board, say Y here, otherwise N.
 
-	  To compile this driver as a module, choose M here: the
-	  module will be called wdt_pci.
-
-config WDT_501_PCI
-	bool "PCI-WDT501 features"
-	depends on WDTPCI
-	help
-	  Saying Y here and creating a character special file /dev/temperature
-	  with major number 10 and minor number 131 ("man mknod") will give
-	  you a thermometer inside your computer: reading from
-	  /dev/temperature yields one byte, the temperature in degrees
-	  Fahrenheit. This works only if you have a PCI-WDT501 watchdog board
-	  installed.
+	  If you have a PCI-WDT501 watchdog board then you can enable the
+	  temperature sensor by setting the type parameter to 501.
 
 	  If you want to enable the Fan Tachometer on the PCI-WDT501, then you
 	  can do this via the tachometer parameter. Only do this if you have a
 	  fan tachometer actually set up.
 
+	  To compile this driver as a module, choose M here: the
+	  module will be called wdt_pci.
+
 #
 # USB-based Watchdog Cards
 #

drivers/watchdog/Makefile

@@ -28,6 +28,7 @@ obj-$(CONFIG_USBPCWATCHDOG) += pcwd_usb.o
 obj-$(CONFIG_AT91RM9200_WATCHDOG) += at91rm9200_wdt.o
 obj-$(CONFIG_AT91SAM9X_WATCHDOG) += at91sam9_wdt.o
 obj-$(CONFIG_OMAP_WATCHDOG) += omap_wdt.o
+obj-$(CONFIG_TWL4030_WATCHDOG) += twl4030_wdt.o
 obj-$(CONFIG_21285_WATCHDOG) += wdt285.o
 obj-$(CONFIG_977_WATCHDOG) += wdt977.o
 obj-$(CONFIG_IXP2000_WATCHDOG) += ixp2000_wdt.o
@@ -41,6 +42,8 @@ obj-$(CONFIG_PNX4008_WATCHDOG) += pnx4008_wdt.o
 obj-$(CONFIG_IOP_WATCHDOG) += iop_wdt.o
 obj-$(CONFIG_DAVINCI_WATCHDOG) += davinci_wdt.o
 obj-$(CONFIG_ORION_WATCHDOG) += orion_wdt.o
+obj-$(CONFIG_COH901327_WATCHDOG) += coh901327_wdt.o
+obj-$(CONFIG_STMP3XXX_WATCHDOG) += stmp3xxx_wdt.o
 
 # AVR32 Architecture
 obj-$(CONFIG_AT32AP700X_WDT) += at32ap700x_wdt.o
@@ -98,9 +101,11 @@ obj-$(CONFIG_SBC_EPX_C3_WATCHDOG) += sbc_epx_c3.o
 # M68KNOMMU Architecture
 
 # MIPS Architecture
+obj-$(CONFIG_BCM47XX_WDT) += bcm47xx_wdt.o
 obj-$(CONFIG_RC32434_WDT) += rc32434_wdt.o
 obj-$(CONFIG_INDYDOG) += indydog.o
 obj-$(CONFIG_WDT_MTX1) += mtx-1_wdt.o
+obj-$(CONFIG_PNX833X_WDT) += pnx833x_wdt.o
 obj-$(CONFIG_WDT_RM9K_GPI) += rm9k_wdt.o
 obj-$(CONFIG_SIBYTE_WDOG) += sb_wdog.o
 obj-$(CONFIG_AR7_WDT) += ar7_wdt.o