Merge tag 'linux-can-fixes-for-5.5-20191208' of git://git.kernel.org/…

…pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2019-12-08

this is a pull request of 13 patches for net/master.

The first two patches are by Dan Murphy. He adds himself as a maintainer to the
m-can MMIO and tcan SPI driver.

The next two patches the j1939 stack. The first one is by Oleksij Rempel and
fixes a locking problem found by the syzbot, the second one is by me an fixes a
mistake in the documentation.

Srinivas Neeli fixes missing RX CAN packets on CANFD2.0 in the xilinx driver.

Sean Nyekjaer fixes a possible deadlock in the the flexcan driver after
suspend/resume. Joakim Zhang contributes two patches for the flexcan driver
that fix problems with the low power enter/exit.

The next 4 patches all target the tcan part of the m_can driver. Sean Nyekjaer
adds the required delay after reset and fixes the device tree binding example.
Dan Murphy's patches make the wake-gpio optional.

In the last patch Xiaolong Huang fixes several kernel memory info leaks to the
USB device in the kvaser_usb_leaf driver.
====================

Signed-off-by: David S. Miller <[email protected]>

Documentation/devicetree/bindings/net/can/tcan4x5x.txt

@@ -10,7 +10,6 @@ Required properties:
 	- #size-cells: 0
 	- spi-max-frequency: Maximum frequency of the SPI bus the chip can
 			     operate at should be less than or equal to 18 MHz.
-	- device-wake-gpios: Wake up GPIO to wake up the TCAN device.
 	- interrupt-parent: the phandle to the interrupt controller which provides
                     the interrupt.
 	- interrupts: interrupt specification for data-ready.
@@ -23,6 +22,7 @@ Optional properties:
 		       reset.
 	- device-state-gpios: Input GPIO that indicates if the device is in
 			      a sleep state or if the device is active.
+	- device-wake-gpios: Wake up GPIO to wake up the TCAN device.
 
 Example:
 tcan4x5x: tcan4x5x@0 {
@@ -36,5 +36,5 @@ tcan4x5x: tcan4x5x@0 {
 		interrupts = <14 GPIO_ACTIVE_LOW>;
 		device-state-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
 		device-wake-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
-		reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+		reset-gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>;
 };

Documentation/networking/j1939.rst

@@ -339,7 +339,7 @@ To claim an address following code example can be used:
 			.pgn = J1939_PGN_ADDRESS_CLAIMED,
 			.pgn_mask = J1939_PGN_PDU1_MAX,
 		}, {
-			.pgn = J1939_PGN_ADDRESS_REQUEST,
+			.pgn = J1939_PGN_REQUEST,
 			.pgn_mask = J1939_PGN_PDU1_MAX,
 		}, {
 			.pgn = J1939_PGN_ADDRESS_COMMANDED,

MAINTAINERS

@@ -10108,6 +10108,7 @@ S:	Maintained
 F:	drivers/media/radio/radio-maxiradio*
 
 MCAN MMIO DEVICE DRIVER
+M:	Dan Murphy <[email protected]>
 M:	Sriram Dash <[email protected]>
 L:	[email protected]
 S:	Maintained
@@ -16533,6 +16534,13 @@ L:	[email protected] (moderated for non-subscribers)
 S:	Odd Fixes
 F:	sound/soc/codecs/tas571x*
 
+TI TCAN4X5X DEVICE DRIVER
+M:	Dan Murphy <[email protected]>
+L:	[email protected]
+S:	Maintained
+F:	Documentation/devicetree/bindings/net/can/tcan4x5x.txt
+F:	drivers/net/can/m_can/tcan4x5x.c
+
 TI TRF7970A NFC DRIVER
 M:	Mark Greer <[email protected]>
 L:	[email protected]

drivers/net/can/flexcan.c

@@ -389,6 +389,34 @@ static struct flexcan_mb __iomem *flexcan_get_mb(const struct flexcan_priv *priv
 		(&priv->regs->mb[bank][priv->mb_size * mb_index]);
 }
 
+static int flexcan_low_power_enter_ack(struct flexcan_priv *priv)
+{
+	struct flexcan_regs __iomem *regs = priv->regs;
+	unsigned int timeout = FLEXCAN_TIMEOUT_US / 10;
+
+	while (timeout-- && !(priv->read(&regs->mcr) & FLEXCAN_MCR_LPM_ACK))
+		udelay(10);
+
+	if (!(priv->read(&regs->mcr) & FLEXCAN_MCR_LPM_ACK))
+		return -ETIMEDOUT;
+
+	return 0;
+}
+
+static int flexcan_low_power_exit_ack(struct flexcan_priv *priv)
+{
+	struct flexcan_regs __iomem *regs = priv->regs;
+	unsigned int timeout = FLEXCAN_TIMEOUT_US / 10;
+
+	while (timeout-- && (priv->read(&regs->mcr) & FLEXCAN_MCR_LPM_ACK))
+		udelay(10);
+
+	if (priv->read(&regs->mcr) & FLEXCAN_MCR_LPM_ACK)
+		return -ETIMEDOUT;
+
+	return 0;
+}
+
 static void flexcan_enable_wakeup_irq(struct flexcan_priv *priv, bool enable)
 {
 	struct flexcan_regs __iomem *regs = priv->regs;
@@ -407,7 +435,6 @@ static void flexcan_enable_wakeup_irq(struct flexcan_priv *priv, bool enable)
 static inline int flexcan_enter_stop_mode(struct flexcan_priv *priv)
 {
 	struct flexcan_regs __iomem *regs = priv->regs;
-	unsigned int ackval;
 	u32 reg_mcr;
 
 	reg_mcr = priv->read(&regs->mcr);
@@ -418,36 +445,24 @@ static inline int flexcan_enter_stop_mode(struct flexcan_priv *priv)
 	regmap_update_bits(priv->stm.gpr, priv->stm.req_gpr,
 			   1 << priv->stm.req_bit, 1 << priv->stm.req_bit);
 
-	/* get stop acknowledgment */
-	if (regmap_read_poll_timeout(priv->stm.gpr, priv->stm.ack_gpr,
-				     ackval, ackval & (1 << priv->stm.ack_bit),
-				     0, FLEXCAN_TIMEOUT_US))
-		return -ETIMEDOUT;
-
-	return 0;
+	return flexcan_low_power_enter_ack(priv);
 }
 
 static inline int flexcan_exit_stop_mode(struct flexcan_priv *priv)
 {
 	struct flexcan_regs __iomem *regs = priv->regs;
-	unsigned int ackval;
 	u32 reg_mcr;
 
 	/* remove stop request */
 	regmap_update_bits(priv->stm.gpr, priv->stm.req_gpr,
 			   1 << priv->stm.req_bit, 0);
 
-	/* get stop acknowledgment */
-	if (regmap_read_poll_timeout(priv->stm.gpr, priv->stm.ack_gpr,
-				     ackval, !(ackval & (1 << priv->stm.ack_bit)),
-				     0, FLEXCAN_TIMEOUT_US))
-		return -ETIMEDOUT;
 
 	reg_mcr = priv->read(&regs->mcr);
 	reg_mcr &= ~FLEXCAN_MCR_SLF_WAK;
 	priv->write(reg_mcr, &regs->mcr);
 
-	return 0;
+	return flexcan_low_power_exit_ack(priv);
 }
 
 static inline void flexcan_error_irq_enable(const struct flexcan_priv *priv)
@@ -506,39 +521,25 @@ static inline int flexcan_transceiver_disable(const struct flexcan_priv *priv)
 static int flexcan_chip_enable(struct flexcan_priv *priv)
 {
 	struct flexcan_regs __iomem *regs = priv->regs;
-	unsigned int timeout = FLEXCAN_TIMEOUT_US / 10;
 	u32 reg;
 
 	reg = priv->read(&regs->mcr);
 	reg &= ~FLEXCAN_MCR_MDIS;
 	priv->write(reg, &regs->mcr);
 
-	while (timeout-- && (priv->read(&regs->mcr) & FLEXCAN_MCR_LPM_ACK))
-		udelay(10);
-
-	if (priv->read(&regs->mcr) & FLEXCAN_MCR_LPM_ACK)
-		return -ETIMEDOUT;
-
-	return 0;
+	return flexcan_low_power_exit_ack(priv);
 }
 
 static int flexcan_chip_disable(struct flexcan_priv *priv)
 {
 	struct flexcan_regs __iomem *regs = priv->regs;
-	unsigned int timeout = FLEXCAN_TIMEOUT_US / 10;
 	u32 reg;
 
 	reg = priv->read(&regs->mcr);
 	reg |= FLEXCAN_MCR_MDIS;
 	priv->write(reg, &regs->mcr);
 
-	while (timeout-- && !(priv->read(&regs->mcr) & FLEXCAN_MCR_LPM_ACK))
-		udelay(10);
-
-	if (!(priv->read(&regs->mcr) & FLEXCAN_MCR_LPM_ACK))
-		return -ETIMEDOUT;
-
-	return 0;
+	return flexcan_low_power_enter_ack(priv);
 }
 
 static int flexcan_chip_freeze(struct flexcan_priv *priv)
@@ -1722,6 +1723,9 @@ static int __maybe_unused flexcan_resume(struct device *device)
 		netif_start_queue(dev);
 		if (device_may_wakeup(device)) {
 			disable_irq_wake(dev->irq);
+			err = flexcan_exit_stop_mode(priv);
+			if (err)
+				return err;
 		} else {
 			err = pm_runtime_force_resume(device);
 			if (err)
@@ -1767,14 +1771,9 @@ static int __maybe_unused flexcan_noirq_resume(struct device *device)
 {
 	struct net_device *dev = dev_get_drvdata(device);
 	struct flexcan_priv *priv = netdev_priv(dev);
-	int err;
 
-	if (netif_running(dev) && device_may_wakeup(device)) {
+	if (netif_running(dev) && device_may_wakeup(device))
 		flexcan_enable_wakeup_irq(priv, false);
-		err = flexcan_exit_stop_mode(priv);
-		if (err)
-			return err;
-	}
 
 	return 0;
 }

drivers/net/can/m_can/tcan4x5x.c

@@ -101,6 +101,8 @@
 #define TCAN4X5X_MODE_STANDBY BIT(6)
 #define TCAN4X5X_MODE_NORMAL BIT(7)
 
+#define TCAN4X5X_DISABLE_WAKE_MSK	(BIT(31) | BIT(30))
+
 #define TCAN4X5X_SW_RESET BIT(2)
 
 #define TCAN4X5X_MCAN_CONFIGURED BIT(5)
@@ -338,22 +340,34 @@ static int tcan4x5x_init(struct m_can_classdev *cdev)
 	return ret;
 }
 
+static int tcan4x5x_disable_wake(struct m_can_classdev *cdev)
+{
+	struct tcan4x5x_priv *tcan4x5x = cdev->device_data;
+
+	return regmap_update_bits(tcan4x5x->regmap, TCAN4X5X_CONFIG,
+				  TCAN4X5X_DISABLE_WAKE_MSK, 0x00);
+}
+
 static int tcan4x5x_parse_config(struct m_can_classdev *cdev)
 {
 	struct tcan4x5x_priv *tcan4x5x = cdev->device_data;
 
 	tcan4x5x->device_wake_gpio = devm_gpiod_get(cdev->dev, "device-wake",
 						    GPIOD_OUT_HIGH);
 	if (IS_ERR(tcan4x5x->device_wake_gpio)) {
-		dev_err(cdev->dev, "device-wake gpio not defined\n");
-		return -EINVAL;
+		if (PTR_ERR(tcan4x5x->power) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+
+		tcan4x5x_disable_wake(cdev);
 	}
 
 	tcan4x5x->reset_gpio = devm_gpiod_get_optional(cdev->dev, "reset",
 						       GPIOD_OUT_LOW);
 	if (IS_ERR(tcan4x5x->reset_gpio))
 		tcan4x5x->reset_gpio = NULL;
 
+	usleep_range(700, 1000);
+
 	tcan4x5x->device_state_gpio = devm_gpiod_get_optional(cdev->dev,
 							      "device-state",
 							      GPIOD_IN);
@@ -428,10 +442,6 @@ static int tcan4x5x_can_probe(struct spi_device *spi)
 
 	spi_set_drvdata(spi, priv);
 
-	ret = tcan4x5x_parse_config(mcan_class);
-	if (ret)
-		goto out_clk;
-
 	/* Configure the SPI bus */
 	spi->bits_per_word = 32;
 	ret = spi_setup(spi);
@@ -441,6 +451,10 @@ static int tcan4x5x_can_probe(struct spi_device *spi)
 	priv->regmap = devm_regmap_init(&spi->dev, &tcan4x5x_bus,
 					&spi->dev, &tcan4x5x_regmap);
 
+	ret = tcan4x5x_parse_config(mcan_class);
+	if (ret)
+		goto out_clk;
+
 	tcan4x5x_power_enable(priv->power, 1);
 
 	ret = m_can_class_register(mcan_class);

drivers/net/can/usb/kvaser_usb/kvaser_usb_leaf.c

@@ -608,7 +608,7 @@ static int kvaser_usb_leaf_simple_cmd_async(struct kvaser_usb_net_priv *priv,
 	struct kvaser_cmd *cmd;
 	int err;
 
-	cmd = kmalloc(sizeof(*cmd), GFP_ATOMIC);
+	cmd = kzalloc(sizeof(*cmd), GFP_ATOMIC);
 	if (!cmd)
 		return -ENOMEM;
 
@@ -1140,7 +1140,7 @@ static int kvaser_usb_leaf_set_opt_mode(const struct kvaser_usb_net_priv *priv)
 	struct kvaser_cmd *cmd;
 	int rc;
 
-	cmd = kmalloc(sizeof(*cmd), GFP_KERNEL);
+	cmd = kzalloc(sizeof(*cmd), GFP_KERNEL);
 	if (!cmd)
 		return -ENOMEM;
 
@@ -1206,7 +1206,7 @@ static int kvaser_usb_leaf_flush_queue(struct kvaser_usb_net_priv *priv)
 	struct kvaser_cmd *cmd;
 	int rc;
 
-	cmd = kmalloc(sizeof(*cmd), GFP_KERNEL);
+	cmd = kzalloc(sizeof(*cmd), GFP_KERNEL);
 	if (!cmd)
 		return -ENOMEM;
 

drivers/net/can/xilinx_can.c

@@ -60,6 +60,8 @@ enum xcan_reg {
 	XCAN_TXMSG_BASE_OFFSET	= 0x0100, /* TX Message Space */
 	XCAN_RXMSG_BASE_OFFSET	= 0x1100, /* RX Message Space */
 	XCAN_RXMSG_2_BASE_OFFSET	= 0x2100, /* RX Message Space */
+	XCAN_AFR_2_MASK_OFFSET	= 0x0A00, /* Acceptance Filter MASK */
+	XCAN_AFR_2_ID_OFFSET	= 0x0A04, /* Acceptance Filter ID */
 };
 
 #define XCAN_FRAME_ID_OFFSET(frame_base)	((frame_base) + 0x00)
@@ -1809,6 +1811,11 @@ static int xcan_probe(struct platform_device *pdev)
 
 	pm_runtime_put(&pdev->dev);
 
+	if (priv->devtype.flags & XCAN_FLAG_CANFD_2) {
+		priv->write_reg(priv, XCAN_AFR_2_ID_OFFSET, 0x00000000);
+		priv->write_reg(priv, XCAN_AFR_2_MASK_OFFSET, 0x00000000);
+	}
+
 	netdev_dbg(ndev, "reg_base=0x%p irq=%d clock=%d, tx buffers: actual %d, using %d\n",
 		   priv->reg_base, ndev->irq, priv->can.clock.freq,
 		   hw_tx_max, priv->tx_max);

net/can/j1939/socket.c

@@ -423,9 +423,9 @@ static int j1939_sk_bind(struct socket *sock, struct sockaddr *uaddr, int len)
 {
 	struct sockaddr_can *addr = (struct sockaddr_can *)uaddr;
 	struct j1939_sock *jsk = j1939_sk(sock->sk);
-	struct j1939_priv *priv = jsk->priv;
-	struct sock *sk = sock->sk;
-	struct net *net = sock_net(sk);
+	struct j1939_priv *priv;
+	struct sock *sk;
+	struct net *net;
 	int ret = 0;
 
 	ret = j1939_sk_sanity_check(addr, len);
@@ -434,6 +434,10 @@ static int j1939_sk_bind(struct socket *sock, struct sockaddr *uaddr, int len)
 
 	lock_sock(sock->sk);
 
+	priv = jsk->priv;
+	sk = sock->sk;
+	net = sock_net(sk);
+
 	/* Already bound to an interface? */
 	if (jsk->state & J1939_SOCK_BOUND) {
 		/* A re-bind() to a different interface is not