Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel…

…/git/arm/arm-soc

Pull ARM SoC fixes from Olof Johansson:
 "Again, a batch that's been sitting a couple of weeks, mostly because
  I anticipated a bit more material but it didn't show up -- which is
  good.

  These are all your garden variety fixes for ARM platforms.

  The most visible issue fixed here is probably the SMP reset issue on
  OMAP, the rest are minor stuff"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: allwinner: a64: add pmu0 regs for USB PHY
  ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer
  reset: add exported __reset_control_get, return NULL if optional
  ARM: orion5x: only call into phylib when available
  ARM: omap2+: Revert omap-smp.c changes resetting CPU1 during boot
  ARM: dts: am335x-evmsk: adjust mmc2 param to allow suspend
  ARM: dts: ti: fix PCI bus dtc warnings
  ARM: dts: am335x-baltos: disable EEE for Atheros 8035 PHY
  ARM: dts: OMAP3: Fix MFG ID EEPROM
  ARM: sun8i: a33: add operating-points-v2 property to all nodes
  ARM: sun8i: a33: remove highest OPP to fix CPU crashes

arch/arm/boot/dts/am335x-baltos.dtsi

@@ -371,6 +371,8 @@
 
 	phy1: ethernet-phy@1 {
 		reg = <7>;
+		eee-broken-100tx;
+		eee-broken-1000t;
 	};
 };
 

arch/arm/boot/dts/am335x-evmsk.dts

@@ -672,6 +672,7 @@
 	ti,non-removable;
 	bus-width = <4>;
 	cap-power-off-card;
+	keep-power-in-suspend;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_pins>;
 

arch/arm/boot/dts/dra7.dtsi

@@ -283,6 +283,7 @@
 				device_type = "pci";
 				ranges = <0x81000000 0 0          0x03000 0 0x00010000
 					  0x82000000 0 0x20013000 0x13000 0 0xffed000>;
+				bus-range = <0x00 0xff>;
 				#interrupt-cells = <1>;
 				num-lanes = <1>;
 				linux,pci-domain = <0>;
@@ -319,6 +320,7 @@
 				device_type = "pci";
 				ranges = <0x81000000 0 0          0x03000 0 0x00010000
 					  0x82000000 0 0x30013000 0x13000 0 0xffed000>;
+				bus-range = <0x00 0xff>;
 				#interrupt-cells = <1>;
 				num-lanes = <1>;
 				linux,pci-domain = <1>;

arch/arm/boot/dts/logicpd-torpedo-som.dtsi

@@ -121,7 +121,7 @@
 &i2c3 {
 	clock-frequency = <400000>;
 	at24@50 {
-		compatible = "at24,24c02";
+		compatible = "atmel,24c64";
 		readonly;
 		reg = <0x50>;
 	};

arch/arm/boot/dts/sun8i-a33.dtsi

@@ -66,12 +66,6 @@
 			opp-microvolt = <1200000>;
 			clock-latency-ns = <244144>; /* 8 32k periods */
 		};
-
-		opp@1200000000 {
-			opp-hz = /bits/ 64 <1200000000>;
-			opp-microvolt = <1320000>;
-			clock-latency-ns = <244144>; /* 8 32k periods */
-		};
 	};
 
 	cpus {
@@ -81,16 +75,22 @@
 			operating-points-v2 = <&cpu0_opp_table>;
 		};
 
+		cpu@1 {
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
 		cpu@2 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <2>;
+			operating-points-v2 = <&cpu0_opp_table>;
 		};
 
 		cpu@3 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <3>;
+			operating-points-v2 = <&cpu0_opp_table>;
 		};
 	};
 

arch/arm/mach-omap2/common.h

@@ -270,6 +270,7 @@ extern const struct smp_operations omap4_smp_ops;
 extern int omap4_mpuss_init(void);
 extern int omap4_enter_lowpower(unsigned int cpu, unsigned int power_state);
 extern int omap4_hotplug_cpu(unsigned int cpu, unsigned int power_state);
+extern u32 omap4_get_cpu1_ns_pa_addr(void);
 #else
 static inline int omap4_enter_lowpower(unsigned int cpu,
 					unsigned int power_state)

arch/arm/mach-omap2/omap-hotplug.c

@@ -50,7 +50,7 @@ void omap4_cpu_die(unsigned int cpu)
 		omap4_hotplug_cpu(cpu, PWRDM_POWER_OFF);
 
 		if (omap_secure_apis_support())
-			boot_cpu = omap_read_auxcoreboot0();
+			boot_cpu = omap_read_auxcoreboot0() >> 9;
 		else
 			boot_cpu =
 				readl_relaxed(base + OMAP_AUX_CORE_BOOT_0) >> 5;

arch/arm/mach-omap2/omap-mpuss-lowpower.c

@@ -64,6 +64,7 @@
 #include "prm-regbits-44xx.h"
 
 static void __iomem *sar_base;
+static u32 old_cpu1_ns_pa_addr;
 
 #if defined(CONFIG_PM) && defined(CONFIG_SMP)
 
@@ -212,6 +213,11 @@ static void __init save_l2x0_context(void)
 {}
 #endif
 
+u32 omap4_get_cpu1_ns_pa_addr(void)
+{
+	return old_cpu1_ns_pa_addr;
+}
+
 /**
  * omap4_enter_lowpower: OMAP4 MPUSS Low Power Entry Function
  * The purpose of this function is to manage low power programming
@@ -460,22 +466,30 @@ int __init omap4_mpuss_init(void)
 void __init omap4_mpuss_early_init(void)
 {
 	unsigned long startup_pa;
+	void __iomem *ns_pa_addr;
 
-	if (!(cpu_is_omap44xx() || soc_is_omap54xx()))
+	if (!(soc_is_omap44xx() || soc_is_omap54xx()))
 		return;
 
 	sar_base = omap4_get_sar_ram_base();
 
-	if (cpu_is_omap443x())
+	/* Save old NS_PA_ADDR for validity checks later on */
+	if (soc_is_omap44xx())
+		ns_pa_addr = sar_base + CPU1_WAKEUP_NS_PA_ADDR_OFFSET;
+	else
+		ns_pa_addr = sar_base + OMAP5_CPU1_WAKEUP_NS_PA_ADDR_OFFSET;
+	old_cpu1_ns_pa_addr = readl_relaxed(ns_pa_addr);
+
+	if (soc_is_omap443x())
 		startup_pa = __pa_symbol(omap4_secondary_startup);
-	else if (cpu_is_omap446x())
+	else if (soc_is_omap446x())
 		startup_pa = __pa_symbol(omap4460_secondary_startup);
 	else if ((__boot_cpu_mode & MODE_MASK) == HYP_MODE)
 		startup_pa = __pa_symbol(omap5_secondary_hyp_startup);
 	else
 		startup_pa = __pa_symbol(omap5_secondary_startup);
 
-	if (cpu_is_omap44xx())
+	if (soc_is_omap44xx())
 		writel_relaxed(startup_pa, sar_base +
 			       CPU1_WAKEUP_NS_PA_ADDR_OFFSET);
 	else

arch/arm/mach-omap2/omap-smc.S

@@ -94,6 +94,5 @@ ENTRY(omap_read_auxcoreboot0)
 	ldr	r12, =0x103
 	dsb
 	smc	#0
-	mov	r0, r0, lsr #9
 	ldmfd   sp!, {r2-r12, pc}
 ENDPROC(omap_read_auxcoreboot0)

arch/arm/mach-omap2/omap-smp.c

@@ -21,6 +21,7 @@
 #include <linux/io.h>
 #include <linux/irqchip/arm-gic.h>
 
+#include <asm/sections.h>
 #include <asm/smp_scu.h>
 #include <asm/virt.h>
 
@@ -40,10 +41,14 @@
 
 #define OMAP5_CORE_COUNT	0x2
 
+#define AUX_CORE_BOOT0_GP_RELEASE	0x020
+#define AUX_CORE_BOOT0_HS_RELEASE	0x200
+
 struct omap_smp_config {
 	unsigned long cpu1_rstctrl_pa;
 	void __iomem *cpu1_rstctrl_va;
 	void __iomem *scu_base;
+	void __iomem *wakeupgen_base;
 	void *startup_addr;
 };
 
@@ -140,7 +145,6 @@ static int omap4_boot_secondary(unsigned int cpu, struct task_struct *idle)
 	static struct clockdomain *cpu1_clkdm;
 	static bool booted;
 	static struct powerdomain *cpu1_pwrdm;
-	void __iomem *base = omap_get_wakeupgen_base();
 
 	/*
 	 * Set synchronisation state between this boot processor
@@ -155,9 +159,11 @@ static int omap4_boot_secondary(unsigned int cpu, struct task_struct *idle)
 	 * A barrier is added to ensure that write buffer is drained
 	 */
 	if (omap_secure_apis_support())
-		omap_modify_auxcoreboot0(0x200, 0xfffffdff);
+		omap_modify_auxcoreboot0(AUX_CORE_BOOT0_HS_RELEASE,
+					 0xfffffdff);
 	else
-		writel_relaxed(0x20, base + OMAP_AUX_CORE_BOOT_0);
+		writel_relaxed(AUX_CORE_BOOT0_GP_RELEASE,
+			       cfg.wakeupgen_base + OMAP_AUX_CORE_BOOT_0);
 
 	if (!cpu1_clkdm && !cpu1_pwrdm) {
 		cpu1_clkdm = clkdm_lookup("mpu1_clkdm");
@@ -261,9 +267,72 @@ static void __init omap4_smp_init_cpus(void)
 		set_cpu_possible(i, true);
 }
 
+/*
+ * For now, just make sure the start-up address is not within the booting
+ * kernel space as that means we just overwrote whatever secondary_startup()
+ * code there was.
+ */
+static bool __init omap4_smp_cpu1_startup_valid(unsigned long addr)
+{
+	if ((addr >= __pa(PAGE_OFFSET)) && (addr <= __pa(__bss_start)))
+		return false;
+
+	return true;
+}
+
+/*
+ * We may need to reset CPU1 before configuring, otherwise kexec boot can end
+ * up trying to use old kernel startup address or suspend-resume will
+ * occasionally fail to bring up CPU1 on 4430 if CPU1 fails to enter deeper
+ * idle states.
+ */
+static void __init omap4_smp_maybe_reset_cpu1(struct omap_smp_config *c)
+{
+	unsigned long cpu1_startup_pa, cpu1_ns_pa_addr;
+	bool needs_reset = false;
+	u32 released;
+
+	if (omap_secure_apis_support())
+		released = omap_read_auxcoreboot0() & AUX_CORE_BOOT0_HS_RELEASE;
+	else
+		released = readl_relaxed(cfg.wakeupgen_base +
+					 OMAP_AUX_CORE_BOOT_0) &
+						AUX_CORE_BOOT0_GP_RELEASE;
+	if (released) {
+		pr_warn("smp: CPU1 not parked?\n");
+
+		return;
+	}
+
+	cpu1_startup_pa = readl_relaxed(cfg.wakeupgen_base +
+					OMAP_AUX_CORE_BOOT_1);
+	cpu1_ns_pa_addr = omap4_get_cpu1_ns_pa_addr();
+
+	/* Did the configured secondary_startup() get overwritten? */
+	if (!omap4_smp_cpu1_startup_valid(cpu1_startup_pa))
+		needs_reset = true;
+
+	/*
+	 * If omap4 or 5 has NS_PA_ADDR configured, CPU1 may be in a
+	 * deeper idle state in WFI and will wake to an invalid address.
+	 */
+	if ((soc_is_omap44xx() || soc_is_omap54xx()) &&
+	    !omap4_smp_cpu1_startup_valid(cpu1_ns_pa_addr))
+		needs_reset = true;
+
+	if (!needs_reset || !c->cpu1_rstctrl_va)
+		return;
+
+	pr_info("smp: CPU1 parked within kernel, needs reset (0x%lx 0x%lx)\n",
+		cpu1_startup_pa, cpu1_ns_pa_addr);
+
+	writel_relaxed(1, c->cpu1_rstctrl_va);
+	readl_relaxed(c->cpu1_rstctrl_va);
+	writel_relaxed(0, c->cpu1_rstctrl_va);
+}
+
 static void __init omap4_smp_prepare_cpus(unsigned int max_cpus)
 {
-	void __iomem *base = omap_get_wakeupgen_base();
 	const struct omap_smp_config *c = NULL;
 
 	if (soc_is_omap443x())
@@ -281,6 +350,7 @@ static void __init omap4_smp_prepare_cpus(unsigned int max_cpus)
 	/* Must preserve cfg.scu_base set earlier */
 	cfg.cpu1_rstctrl_pa = c->cpu1_rstctrl_pa;
 	cfg.startup_addr = c->startup_addr;
+	cfg.wakeupgen_base = omap_get_wakeupgen_base();
 
 	if (soc_is_dra74x() || soc_is_omap54xx()) {
 		if ((__boot_cpu_mode & MODE_MASK) == HYP_MODE)
@@ -299,15 +369,7 @@ static void __init omap4_smp_prepare_cpus(unsigned int max_cpus)
 	if (cfg.scu_base)
 		scu_enable(cfg.scu_base);
 
-	/*
-	 * Reset CPU1 before configuring, otherwise kexec will
-	 * end up trying to use old kernel startup address.
-	 */
-	if (cfg.cpu1_rstctrl_va) {
-		writel_relaxed(1, cfg.cpu1_rstctrl_va);
-		readl_relaxed(cfg.cpu1_rstctrl_va);
-		writel_relaxed(0, cfg.cpu1_rstctrl_va);
-	}
+	omap4_smp_maybe_reset_cpu1(&cfg);
 
 	/*
 	 * Write the address of secondary startup routine into the
@@ -319,7 +381,7 @@ static void __init omap4_smp_prepare_cpus(unsigned int max_cpus)
 		omap_auxcoreboot_addr(__pa_symbol(cfg.startup_addr));
 	else
 		writel_relaxed(__pa_symbol(cfg.startup_addr),
-			       base + OMAP_AUX_CORE_BOOT_1);
+			       cfg.wakeupgen_base + OMAP_AUX_CORE_BOOT_1);
 }
 
 const struct smp_operations omap4_smp_ops __initconst = {

arch/arm/mach-omap2/omap_device.c

@@ -222,6 +222,14 @@ static int _omap_device_notifier_call(struct notifier_block *nb,
 				dev_err(dev, "failed to idle\n");
 		}
 		break;
+	case BUS_NOTIFY_BIND_DRIVER:
+		od = to_omap_device(pdev);
+		if (od && (od->_state == OMAP_DEVICE_STATE_ENABLED) &&
+		    pm_runtime_status_suspended(dev)) {
+			od->_driver_status = BUS_NOTIFY_BIND_DRIVER;
+			pm_runtime_set_active(dev);
+		}
+		break;
 	case BUS_NOTIFY_ADD_DEVICE:
 		if (pdev->dev.of_node)
 			omap_device_build_from_dt(pdev);

arch/arm/mach-orion5x/Kconfig

@@ -6,6 +6,7 @@ menuconfig ARCH_ORION5X
 	select GPIOLIB
 	select MVEBU_MBUS
 	select PCI
+	select PHYLIB if NETDEVICES
 	select PLAT_ORION_LEGACY
 	help
 	  Support for the following Marvell Orion 5x series SoCs:

arch/arm/plat-orion/common.c

@@ -468,6 +468,7 @@ void __init orion_ge11_init(struct mv643xx_eth_platform_data *eth_data,
 		    eth_data, &orion_ge11);
 }
 
+#ifdef CONFIG_ARCH_ORION5X
 /*****************************************************************************
  * Ethernet switch
  ****************************************************************************/
@@ -480,6 +481,9 @@ void __init orion_ge00_switch_init(struct dsa_chip_data *d)
 	struct mdio_board_info *bd;
 	unsigned int i;
 
+	if (!IS_BUILTIN(CONFIG_PHYLIB))
+		return;
+
 	for (i = 0; i < ARRAY_SIZE(d->port_names); i++)
 		if (!strcmp(d->port_names[i], "cpu"))
 			break;
@@ -493,6 +497,7 @@ void __init orion_ge00_switch_init(struct dsa_chip_data *d)
 
 	mdiobus_register_board_info(&orion_ge00_switch_board_info, 1);
 }
+#endif
 
 /*****************************************************************************
  * I2C

arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi

@@ -179,8 +179,10 @@
 		usbphy: phy@01c19400 {
 			compatible = "allwinner,sun50i-a64-usb-phy";
 			reg = <0x01c19400 0x14>,
+			      <0x01c1a800 0x4>,
 			      <0x01c1b800 0x4>;
 			reg-names = "phy_ctrl",
+				    "pmu0",
 				    "pmu1";
 			clocks = <&ccu CLK_USB_PHY0>,
 				 <&ccu CLK_USB_PHY1>;