Merge branch 'perf/urgent' into perf/core, to pick up fixes

Signed-off-by: Ingo Molnar <[email protected]>

Documentation/admin-guide/kernel-parameters.txt

@@ -4846,3 +4846,8 @@
 	xirc2ps_cs=	[NET,PCMCIA]
 			Format:
 			<irq>,<irq_mask>,<io>,<full_duplex>,<do_sound>,<lockup_hack>[,<irq2>[,<irq3>[,<irq4>]]]
+
+	xhci-hcd.quirks		[USB,KNL]
+			A hex value specifying bitmask with supplemental xhci
+			host controller quirks. Meaning of each bit can be
+			consulted in header drivers/usb/host/xhci.h.

Documentation/admin-guide/pm/intel_pstate.rst

@@ -324,8 +324,7 @@ Global Attributes
 
 ``intel_pstate`` exposes several global attributes (files) in ``sysfs`` to
 control its functionality at the system level.  They are located in the
-``/sys/devices/system/cpu/cpufreq/intel_pstate/`` directory and affect all
-CPUs.
+``/sys/devices/system/cpu/intel_pstate/`` directory and affect all CPUs.
 
 Some of them are not present if the ``intel_pstate=per_cpu_perf_limits``
 argument is passed to the kernel in the command line.
@@ -379,6 +378,17 @@ argument is passed to the kernel in the command line.
 	but it affects the maximum possible value of per-policy P-state	limits
 	(see `Interpretation of Policy Attributes`_ below for details).
 
+``hwp_dynamic_boost``
+	This attribute is only present if ``intel_pstate`` works in the
+	`active mode with the HWP feature enabled <Active Mode With HWP_>`_ in
+	the processor.  If set (equal to 1), it causes the minimum P-state limit
+	to be increased dynamically for a short time whenever a task previously
+	waiting on I/O is selected to run on a given logical CPU (the purpose
+	of this mechanism is to improve performance).
+
+	This setting has no effect on logical CPUs whose minimum P-state limit
+	is directly set to the highest non-turbo P-state or above it.
+
 .. _status_attr:
 
 ``status``

Documentation/device-mapper/writecache.txt

@@ -15,6 +15,8 @@ Constructor parameters:
    size)
 5. the number of optional parameters (the parameters with an argument
    count as two)
+	start_sector n		(default: 0)
+		offset from the start of cache device in 512-byte sectors
 	high_watermark n	(default: 50)
 		start writeback when the number of used blocks reach this
 		watermark

Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt

@@ -66,7 +66,7 @@ Required root node properties:
 	- "insignal,arndale-octa" - for Exynos5420-based Insignal Arndale
 				    Octa board.
 	- "insignal,origen"       - for Exynos4210-based Insignal Origen board.
-	- "insignal,origen4412    - for Exynos4412-based Insignal Origen board.
+	- "insignal,origen4412"   - for Exynos4412-based Insignal Origen board.
 
 
 Optional nodes:

Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt

@@ -36,7 +36,7 @@ Optional nodes:
 
  - port/ports: to describe a connection to an external encoder. The
    binding follows Documentation/devicetree/bindings/graph.txt and
-   suppors a single port with a single endpoint.
+   supports a single port with a single endpoint.
 
  - See also Documentation/devicetree/bindings/display/tilcdc/panel.txt and
    Documentation/devicetree/bindings/display/tilcdc/tfp410.txt for connecting

Documentation/devicetree/bindings/gpio/nintendo,hollywood-gpio.txt

@@ -1,7 +1,7 @@
 Nintendo Wii (Hollywood) GPIO controller
 
 Required properties:
-- compatible: "nintendo,hollywood-gpio
+- compatible: "nintendo,hollywood-gpio"
 - reg: Physical base address and length of the controller's registers.
 - gpio-controller: Marks the device node as a GPIO controller.
 - #gpio-cells: Should be <2>. The first cell is the pin number and the

Documentation/devicetree/bindings/input/sprd,sc27xx-vibra.txt

@@ -0,0 +1,23 @@
+Spreadtrum SC27xx PMIC Vibrator
+
+Required properties:
+- compatible: should be "sprd,sc2731-vibrator".
+- reg: address of vibrator control register.
+
+Example :
+
+	sc2731_pmic: pmic@0 {
+		compatible = "sprd,sc2731";
+		reg = <0>;
+		spi-max-frequency = <26000000>;
+		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vibrator@eb4 {
+			compatible = "sprd,sc2731-vibrator";
+			reg = <0xeb4>;
+		};
+	};

Documentation/devicetree/bindings/input/touchscreen/hideep.txt

@@ -32,7 +32,7 @@ i2c@00000000 {
 		reg = <0x6c>;
 		interrupt-parent = <&gpx1>;
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
-		vdd-supply = <&ldo15_reg>";
+		vdd-supply = <&ldo15_reg>;
 		vid-supply = <&ldo18_reg>;
 		reset-gpios = <&gpx1 5 0>;
 		touchscreen-size-x = <1080>;

Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.txt

@@ -15,7 +15,7 @@ Required properties:
   include "nvidia,tegra30-ictlr".	
 - reg : Specifies base physical address and size of the registers.
   Each controller must be described separately (Tegra20 has 4 of them,
-  whereas Tegra30 and later have 5"  
+  whereas Tegra30 and later have 5).
 - interrupt-controller : Identifies the node as an interrupt controller.
 - #interrupt-cells : Specifies the number of cells needed to encode an
   interrupt source. The value must be 3.

Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt

@@ -12,7 +12,7 @@ Required properties:
   specifier, shall be 2
 - interrupts: interrupts references to primary interrupt controller
   (only needed for exti controller with multiple exti under
-  same parent interrupt: st,stm32-exti and st,stm32h7-exti")
+  same parent interrupt: st,stm32-exti and st,stm32h7-exti)
 
 Example:
 

Documentation/devicetree/bindings/mips/brcm/soc.txt

@@ -152,7 +152,7 @@ Required properties:
 - compatible	: should contain one of:
 		  "brcm,bcm7425-timers"
 		  "brcm,bcm7429-timers"
-		  "brcm,bcm7435-timers and
+		  "brcm,bcm7435-timers" and
 		  "brcm,brcmstb-timers"
 - reg		: the timers register range
 - interrupts	: the interrupt line for this timer block

Documentation/devicetree/bindings/net/fsl-fman.txt

@@ -238,7 +238,7 @@ PROPERTIES
 		Must include one of the following:
 		- "fsl,fman-dtsec" for dTSEC MAC
 		- "fsl,fman-xgec" for XGEC MAC
-		- "fsl,fman-memac for mEMAC MAC
+		- "fsl,fman-memac" for mEMAC MAC
 
 - cell-index
 		Usage: required

Documentation/devicetree/bindings/power/power_domain.txt

@@ -133,7 +133,7 @@ located inside a PM domain with index 0 of a power controller represented by a
 node with the label "power".
 In the second example the consumer device are partitioned across two PM domains,
 the first with index 0 and the second with index 1, of a power controller that
-is represented by a node with the label "power.
+is represented by a node with the label "power".
 
 Optional properties:
 - required-opps: This contains phandle to an OPP node in another device's OPP

Documentation/devicetree/bindings/regulator/tps65090.txt

@@ -16,7 +16,7 @@ Required properties:
 Optional properties:
 - ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3.
   If DCDCs are externally controlled then this property should be there.
-- "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
+- dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
   If DCDCs are externally controlled and if it is from GPIO then GPIO
   number should be provided. If it is externally controlled and no GPIO
   entry then driver will just configure this rails as external control

Documentation/devicetree/bindings/reset/st,sti-softreset.txt

@@ -15,7 +15,7 @@ Please refer to reset.txt in this directory for common reset
 controller binding usage.
 
 Required properties:
-- compatible: Should be st,stih407-softreset";
+- compatible: Should be "st,stih407-softreset";
 - #reset-cells: 1, see below
 
 example:

Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt

@@ -39,7 +39,7 @@ Required properties:
 
 Optional property:
 - clock-frequency:	Desired I2C bus clock frequency in Hz.
-			When missing default to 400000Hz.
+			When missing default to 100000Hz.
 
 Child nodes should conform to I2C bus binding as described in i2c.txt.
 

Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt

@@ -30,7 +30,7 @@ Required properties:
 
 			  Board connectors:
 			  * Headset Mic
-			  * Secondary Mic",
+			  * Secondary Mic
 			  * DMIC
 			  * Ext Spk
 

Documentation/devicetree/bindings/sound/qcom,apq8096.txt

@@ -35,7 +35,7 @@ This binding describes the APQ8096 sound card, which uses qdsp for audio.
 			"Digital Mic3"
 
 		Audio pins and MicBias on WCD9335 Codec:
-			"MIC_BIAS1
+			"MIC_BIAS1"
 			"MIC_BIAS2"
 			"MIC_BIAS3"
 			"MIC_BIAS4"

Documentation/devicetree/bindings/w1/w1-gpio.txt

@@ -15,7 +15,7 @@ Optional properties:
 
 Examples:
 
-	onewire@0 {
+	onewire {
 		compatible = "w1-gpio";
 		gpios = <&gpio 126 0>, <&gpio 105 0>;
 	};

Documentation/filesystems/Locking

@@ -441,8 +441,6 @@ prototypes:
 	int (*iterate) (struct file *, struct dir_context *);
 	int (*iterate_shared) (struct file *, struct dir_context *);
 	__poll_t (*poll) (struct file *, struct poll_table_struct *);
-	struct wait_queue_head * (*get_poll_head)(struct file *, __poll_t);
-	__poll_t (*poll_mask) (struct file *, __poll_t);
 	long (*unlocked_ioctl) (struct file *, unsigned int, unsigned long);
 	long (*compat_ioctl) (struct file *, unsigned int, unsigned long);
 	int (*mmap) (struct file *, struct vm_area_struct *);
@@ -473,7 +471,7 @@ prototypes:
 };
 
 locking rules:
-	All except for ->poll_mask may block.
+	All may block.
 
 ->llseek() locking has moved from llseek to the individual llseek
 implementations.  If your fs is not using generic_file_llseek, you
@@ -505,9 +503,6 @@ in sys_read() and friends.
 the lease within the individual filesystem to record the result of the
 operation
 
-->poll_mask can be called with or without the waitqueue lock for the waitqueue
-returned from ->get_poll_head.
-
 --------------------------- dquot_operations -------------------------------
 prototypes:
 	int (*write_dquot) (struct dquot *);

Documentation/filesystems/vfs.txt

@@ -857,8 +857,6 @@ struct file_operations {
 	ssize_t (*write_iter) (struct kiocb *, struct iov_iter *);
 	int (*iterate) (struct file *, struct dir_context *);
 	__poll_t (*poll) (struct file *, struct poll_table_struct *);
-	struct wait_queue_head * (*get_poll_head)(struct file *, __poll_t);
-	__poll_t (*poll_mask) (struct file *, __poll_t);
 	long (*unlocked_ioctl) (struct file *, unsigned int, unsigned long);
 	long (*compat_ioctl) (struct file *, unsigned int, unsigned long);
 	int (*mmap) (struct file *, struct vm_area_struct *);
@@ -903,17 +901,6 @@ otherwise noted.
 	activity on this file and (optionally) go to sleep until there
 	is activity. Called by the select(2) and poll(2) system calls
 
-  get_poll_head: Returns the struct wait_queue_head that callers can
-  wait on.  Callers need to check the returned events using ->poll_mask
-  once woken.  Can return NULL to indicate polling is not supported,
-  or any error code using the ERR_PTR convention to indicate that a
-  grave error occured and ->poll_mask shall not be called.
-
-  poll_mask: return the mask of EPOLL* values describing the file descriptor
-  state.  Called either before going to sleep on the waitqueue returned by
-  get_poll_head, or after it has been woken.  If ->get_poll_head and
-  ->poll_mask are implemented ->poll does not need to be implement.
-
   unlocked_ioctl: called by the ioctl(2) system call.
 
   compat_ioctl: called by the ioctl(2) system call when 32 bit system calls

Documentation/kbuild/kbuild.txt

@@ -50,6 +50,11 @@ LDFLAGS_MODULE
 --------------------------------------------------
 Additional options used for $(LD) when linking modules.
 
+KBUILD_KCONFIG
+--------------------------------------------------
+Set the top-level Kconfig file to the value of this environment
+variable.  The default name is "Kconfig".
+
 KBUILD_VERBOSE
 --------------------------------------------------
 Set the kbuild verbosity. Can be assigned same values as "V=...".
@@ -88,7 +93,8 @@ In most cases the name of the architecture is the same as the
 directory name found in the arch/ directory.
 But some architectures such as x86 and sparc have aliases.
 x86: i386 for 32 bit, x86_64 for 64 bit
-sparc: sparc for 32 bit, sparc64 for 64 bit
+sh: sh for 32 bit, sh64 for 64 bit
+sparc: sparc32 for 32 bit, sparc64 for 64 bit
 
 CROSS_COMPILE
 --------------------------------------------------
@@ -148,15 +154,6 @@ stripped after they are installed.  If INSTALL_MOD_STRIP is '1', then
 the default option --strip-debug will be used.  Otherwise,
 INSTALL_MOD_STRIP value will be used as the options to the strip command.
 
-INSTALL_FW_PATH
---------------------------------------------------
-INSTALL_FW_PATH specifies where to install the firmware blobs.
-The default value is:
-
-    $(INSTALL_MOD_PATH)/lib/firmware
-
-The value can be overridden in which case the default value is ignored.
-
 INSTALL_HDR_PATH
 --------------------------------------------------
 INSTALL_HDR_PATH specifies where to install user space headers when

Documentation/kbuild/kconfig-language.txt

@@ -430,6 +430,12 @@ This sets the config program's title bar if the config program chooses
 to use it. It should be placed at the top of the configuration, before any
 other statement.
 
+'#' Kconfig source file comment:
+
+An unquoted '#' character anywhere in a source file line indicates
+the beginning of a source file comment.  The remainder of that line
+is a comment.
+
 
 Kconfig hints
 -------------