Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ar…

…m/arm-soc

Pull ARM SoC fixes from Olof Johansson:
 "A series of fixes (and in some cases, some cleanups):

  Via Tony Lindgren:
   - A collection of OMAP regression fixes, in particular because
     firmware no longer sets up all pin states before starting the
     kernel.
   - cpufreq fixes for OMAP (Rafael is on vacation and this was
     pre-agreed).
   - A longer series of misc regression fixes and cleanups, warning
     removals, etc for OMAP

  From Arnd Bergmann:
   - A series of warning fixes for various platforms (defconfig builds)

  Misc:
   - A couple of tegra fixes, one for i.MX, some vt8500 fixes, etc."

* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
  ARM: pxa: armcore: fix PCI PIO warnings
  ARM: integrator: use __iomem pointers for MMIO, part 2
  ARM: assabet: fix bogus warning in get_assabet_scr (again)
  ARM: shmobile: mark shmobile_init_late as __init
  ARM: integrator_cp: fix build failure
  ARM: OMAP4/AM335x: hwmod: fix disable_module regression in hardreset handling
  ARM: OMAP3: fix workaround for EMU clockdomain
  arm/omap: Replace board_ref_clock with enum values
  ARM: OMAP2+: remove duplicated include from board-omap3stalker.c
  arch/arm/plat-omap/omap-pm-noop.c: Remove unecessary semicolon
  arch/arm/mach-omap2: Remove unecessary semicolon
  arch/arm/mach-omap1/devices.c: Remove unecessary semicolon
  ARM/dts: omap5-evm: pinmux configuration for audio
  ARM/dts: Add pinctrl driver entries for omap5
  ARM/dts: omap4-panda: pinmux configuration for audio
  ARM/dts: omap4-sdp: pinmux configuration for audio
  ARM/dts: omap5-evm: Disable unused McBSP3
  ARM/dts: omap4-sdp: Disable unused McBSP3
  ARM/dts: omap4-panda: Disable unused audio IPs
  ARM: OMAP: board-omap4panda: Pin mux configuration for audio needs
  ...

Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt

@@ -7,7 +7,7 @@ as "armctrl" in the SoC documentation, hence naming of this binding.
 
 Required properties:
 
-- compatible : should be "brcm,bcm2835-armctrl-ic.txt"
+- compatible : should be "brcm,bcm2835-armctrl-ic"
 - reg : Specifies base physical address and size of the registers.
 - interrupt-controller : Identifies the node as an interrupt controller
 - #interrupt-cells : Specifies the number of cells needed to encode an

Documentation/devicetree/bindings/timer/brcm,bcm2835-system-timer.txt

@@ -7,7 +7,7 @@ free running counter values, and generates an interrupt.
 
 Required properties:
 
-- compatible : should be "brcm,bcm2835-system-timer.txt"
+- compatible : should be "brcm,bcm2835-system-timer"
 - reg : Specifies base physical address and size of the registers.
 - interrupts : A list of 4 interrupt sinks; one per timer channel.
 - clock-frequency : The frequency of the clock that drives the counter, in Hz.

arch/arm/Kconfig

@@ -494,7 +494,6 @@ config ARCH_IOP32X
 	depends on MMU
 	select CPU_XSCALE
 	select NEED_MACH_GPIO_H
-	select NEED_MACH_IO_H
 	select NEED_RET_TO_USER
 	select PLAT_IOP
 	select PCI
@@ -508,7 +507,6 @@ config ARCH_IOP33X
 	depends on MMU
 	select CPU_XSCALE
 	select NEED_MACH_GPIO_H
-	select NEED_MACH_IO_H
 	select NEED_RET_TO_USER
 	select PLAT_IOP
 	select PCI
@@ -1772,6 +1770,7 @@ source "mm/Kconfig"
 config FORCE_MAX_ZONEORDER
 	int "Maximum zone order" if ARCH_SHMOBILE
 	range 11 64 if ARCH_SHMOBILE
+	default "12" if SOC_AM33XX
 	default "9" if SA1111
 	default "11"
 	help

arch/arm/boot/dts/Makefile

@@ -25,14 +25,6 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
 	exynos4210-trats.dtb \
 	exynos5250-smdk5250.dtb
 dtb-$(CONFIG_ARCH_HIGHBANK) += highbank.dtb
-dtb-$(CONFIG_ARCH_IMX5) += imx51-babbage.dtb \
-	imx53-ard.dtb \
-	imx53-evk.dtb \
-	imx53-qsb.dtb \
-	imx53-smd.dtb
-dtb-$(CONFIG_SOC_IMX6Q) += imx6q-arm2.dtb \
-	imx6q-sabrelite.dtb \
-	imx6q-sabresd.dtb
 dtb-$(CONFIG_ARCH_LPC32XX) += ea3250.dtb phy3250.dtb
 dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-dns320.dtb \
 	kirkwood-dns325.dtb \
@@ -76,7 +68,9 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap4-pandaES.dtb \
 	omap4-var_som.dtb \
 	omap4-sdp.dtb \
-	omap5-evm.dtb
+	omap5-evm.dtb \
+	am335x-evm.dtb \
+	am335x-bone.dtb
 dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb
 dtb-$(CONFIG_ARCH_U8500) += snowball.dtb
 dtb-$(CONFIG_ARCH_SHMOBILE) += emev2-kzm9d.dtb \
@@ -104,5 +98,8 @@ dtb-$(CONFIG_ARCH_VEXPRESS) += vexpress-v2p-ca5s.dtb \
 	vexpress-v2p-ca15-tc1.dtb \
 	vexpress-v2p-ca15_a7.dtb \
 	xenvm-4.2.dtb
+dtb-$(CONFIG_ARCH_VT8500) += vt8500-bv07.dtb \
+	wm8505-ref.dtb \
+	wm8650-mid.dtb
 
 endif

arch/arm/boot/dts/omap4-panda.dts

@@ -59,6 +59,41 @@
 	};
 };
 
+&omap4_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&twl6040_pins
+			&mcpdm_pins
+			&mcbsp1_pins
+	>;
+
+	twl6040_pins: pinmux_twl6040_pins {
+		pinctrl-single,pins = <
+			0xe0 0x3	/* hdq_sio.gpio_127 OUTPUT | MODE3 */
+			0x160 0x100	/* sys_nirq2.sys_nirq2 INPUT | MODE0 */
+		>;
+	};
+
+	mcpdm_pins: pinmux_mcpdm_pins {
+		pinctrl-single,pins = <
+			0xc6 0x108	/* abe_pdm_ul_data.abe_pdm_ul_data INPUT PULLDOWN | MODE0 */
+			0xc8 0x108	/* abe_pdm_dl_data.abe_pdm_dl_data INPUT PULLDOWN | MODE0 */
+			0xca 0x118	/* abe_pdm_frame.abe_pdm_frame INPUT PULLUP | MODE0 */
+			0xcc 0x108	/* abe_pdm_lb_clk.abe_pdm_lb_clk INPUT PULLDOWN | MODE0 */
+			0xce 0x108	/* abe_clks.abe_clks INPUT PULLDOWN | MODE0 */
+		>;
+	};
+
+	mcbsp1_pins: pinmux_mcbsp1_pins {
+		pinctrl-single,pins = <
+			0xbe 0x100	/* abe_mcbsp1_clkx.abe_mcbsp1_clkx INPUT | MODE0 */
+			0xc0 0x108	/* abe_mcbsp1_dr.abe_mcbsp1_dr INPUT PULLDOWN | MODE0 */
+			0xc2 0x8		/* abe_mcbsp1_dx.abe_mcbsp1_dx OUTPUT PULLDOWN | MODE0 */
+			0xc4 0x100	/* abe_mcbsp1_fsx.abe_mcbsp1_fsx INPUT | MODE0 */
+		>;
+	};
+};
+
 &i2c1 {
 	clock-frequency = <400000>;
 
@@ -137,3 +172,15 @@
 	cs1-used;
 	device-handle = <&elpida_ECB240ABACN>;
 };
+
+&mcbsp2 {
+	status = "disabled";
+};
+
+&mcbsp3 {
+	status = "disabled";
+};
+
+&dmic {
+	status = "disabled";
+};

arch/arm/boot/dts/omap4-sdp.dts

@@ -117,6 +117,15 @@
 };
 
 &omap4_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&twl6040_pins
+			&mcpdm_pins
+			&dmic_pins
+			&mcbsp1_pins
+			&mcbsp2_pins
+	>;
+
 	uart2_pins: pinmux_uart2_pins {
 		pinctrl-single,pins = <
 			0xd8 0x118	/* uart2_cts.uart2_cts INPUT_PULLUP | MODE0 */
@@ -141,6 +150,50 @@
 			0x11e 0		/* uart4_tx.uart4_tx OUTPUT | MODE0 */
 		>;
 	};
+
+	twl6040_pins: pinmux_twl6040_pins {
+		pinctrl-single,pins = <
+			0xe0 0x3	/* hdq_sio.gpio_127 OUTPUT | MODE3 */
+			0x160 0x100	/* sys_nirq2.sys_nirq2 INPUT | MODE0 */
+		>;
+	};
+
+	mcpdm_pins: pinmux_mcpdm_pins {
+		pinctrl-single,pins = <
+			0xc6 0x108	/* abe_pdm_ul_data.abe_pdm_ul_data INPUT PULLDOWN | MODE0 */
+			0xc8 0x108	/* abe_pdm_dl_data.abe_pdm_dl_data INPUT PULLDOWN | MODE0 */
+			0xca 0x118	/* abe_pdm_frame.abe_pdm_frame INPUT PULLUP | MODE0 */
+			0xcc 0x108	/* abe_pdm_lb_clk.abe_pdm_lb_clk INPUT PULLDOWN | MODE0 */
+			0xce 0x108	/* abe_clks.abe_clks INPUT PULLDOWN | MODE0 */
+		>;
+	};
+
+	dmic_pins: pinmux_dmic_pins {
+		pinctrl-single,pins = <
+			0xd0 0		/* abe_dmic_clk1.abe_dmic_clk1 OUTPUT | MODE0 */
+			0xd2 0x100	/* abe_dmic_din1.abe_dmic_din1 INPUT | MODE0 */
+			0xd4 0x100	/* abe_dmic_din2.abe_dmic_din2 INPUT | MODE0 */
+			0xd6 0x100	/* abe_dmic_din3.abe_dmic_din3 INPUT | MODE0 */
+		>;
+	};
+
+	mcbsp1_pins: pinmux_mcbsp1_pins {
+		pinctrl-single,pins = <
+			0xbe 0x100	/* abe_mcbsp1_clkx.abe_mcbsp1_clkx INPUT | MODE0 */
+			0xc0 0x108	/* abe_mcbsp1_dr.abe_mcbsp1_dr INPUT PULLDOWN | MODE0 */
+			0xc2 0x8	/* abe_mcbsp1_dx.abe_mcbsp1_dx OUTPUT PULLDOWN | MODE0 */
+			0xc4 0x100	/* abe_mcbsp1_fsx.abe_mcbsp1_fsx INPUT | MODE0 */
+		>;
+	};
+
+	mcbsp2_pins: pinmux_mcbsp2_pins {
+		pinctrl-single,pins = <
+			0xb6 0x100	/* abe_mcbsp2_clkx.abe_mcbsp2_clkx INPUT | MODE0 */
+			0xb8 0x108	/* abe_mcbsp2_dr.abe_mcbsp2_dr INPUT PULLDOWN | MODE0 */
+			0xba 0x8	/* abe_mcbsp2_dx.abe_mcbsp2_dx OUTPUT PULLDOWN | MODE0 */
+			0xbc 0x100	/* abe_mcbsp2_fsx.abe_mcbsp2_fsx INPUT | MODE0 */
+		>;
+	};
 };
 
 &i2c1 {
@@ -349,3 +402,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart4_pins>;
 };
+
+&mcbsp3 {
+	status = "disabled";
+};

arch/arm/boot/dts/omap5-evm.dts

@@ -27,6 +27,60 @@
 
 };
 
+&omap5_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&twl6040_pins
+			&mcpdm_pins
+			&dmic_pins
+			&mcbsp1_pins
+			&mcbsp2_pins
+	>;
+
+	twl6040_pins: pinmux_twl6040_pins {
+		pinctrl-single,pins = <
+			0x18a 0x6	/* perslimbus2_clock.gpio5_145 OUTPUT | MODE6 */
+		>;
+	};
+
+	mcpdm_pins: pinmux_mcpdm_pins {
+		pinctrl-single,pins = <
+			0x142 0x108	/* abe_clks.abe_clks INPUT PULLDOWN | MODE0 */
+			0x15c 0x108	/* abemcpdm_ul_data.abemcpdm_ul_data INPUT PULLDOWN | MODE0 */
+			0x15e 0x108	/* abemcpdm_dl_data.abemcpdm_dl_data INPUT PULLDOWN | MODE0 */
+			0x160 0x118	/* abemcpdm_frame.abemcpdm_frame INPUT PULLUP | MODE0 */
+			0x162 0x108	/* abemcpdm_lb_clk.abemcpdm_lb_clk INPUT PULLDOWN | MODE0 */
+		>;
+	};
+
+	dmic_pins: pinmux_dmic_pins {
+		pinctrl-single,pins = <
+			0x144 0x100	/* abedmic_din1.abedmic_din1 INPUT | MODE0 */
+			0x146 0x100	/* abedmic_din2.abedmic_din2 INPUT | MODE0 */
+			0x148 0x100	/* abedmic_din3.abedmic_din3 INPUT | MODE0 */
+			0x14a 0		/* abedmic_clk1.abedmic_clk1 OUTPUT | MODE0 */
+		>;
+	};
+
+	mcbsp1_pins: pinmux_mcbsp1_pins {
+		pinctrl-single,pins = <
+			0x14c 0x101	/* abedmic_clk2.abemcbsp1_fsx INPUT | MODE1 */
+			0x14e 0x9	/* abedmic_clk3.abemcbsp1_dx OUTPUT PULLDOWN | MODE1 */
+			0x150 0x101	/* abeslimbus1_clock.abemcbsp1_clkx INPUT | MODE0 */
+			0x152 0x109	/* abeslimbus1_data.abemcbsp1_dr INPUT PULLDOWN | MODE1 */
+		>;
+	};
+
+	mcbsp2_pins: pinmux_mcbsp2_pins {
+		pinctrl-single,pins = <
+			0x154 0x108	/* abemcbsp2_dr.abemcbsp2_dr INPUT PULLDOWN | MODE0 */
+			0x156 0x8	/* abemcbsp2_dx.abemcbsp2_dx OUTPUT PULLDOWN | MODE0 */
+			0x158 0x100	/* abemcbsp2_fsx.abemcbsp2_fsx INPUT | MODE0 */
+			0x15a 0x100	/* abemcbsp2_clkx.abemcbsp2_clkx INPUT | MODE0 */
+		>;
+	};
+};
+
 &mmc1 {
 	vmmc-supply = <&vmmcsd_fixed>;
 	bus-width = <4>;
@@ -82,3 +136,7 @@
 			0x020700d9>;	/* SEARCH */
 	linux,input-no-autorepeat;
 };
+
+&mcbsp3 {
+	status = "disabled";
+};

arch/arm/boot/dts/omap5.dtsi

@@ -77,6 +77,23 @@
 		ranges;
 		ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
 
+		omap5_pmx_core: pinmux@4a002840 {
+			compatible = "ti,omap4-padconf", "pinctrl-single";
+			reg = <0x4a002840 0x01b6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-single,register-width = <16>;
+			pinctrl-single,function-mask = <0x7fff>;
+		};
+		omap5_pmx_wkup: pinmux@4ae0c840 {
+			compatible = "ti,omap4-padconf", "pinctrl-single";
+			reg = <0x4ae0c840 0x0038>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-single,register-width = <16>;
+			pinctrl-single,function-mask = <0x7fff>;
+		};
+
 		gic: interrupt-controller@48211000 {
 			compatible = "arm,cortex-a15-gic";
 			interrupt-controller;

arch/arm/boot/dts/tegra20-seaboard.dts

@@ -539,7 +539,7 @@
 		nvidia,invert-interrupt;
 	};
 
-	memory-controller@0x7000f400 {
+	memory-controller@7000f400 {
 		emc-table@190000 {
 			reg = <190000>;
 			compatible = "nvidia,tegra20-emc-table";

arch/arm/boot/dts/tegra20.dtsi

@@ -170,7 +170,7 @@
 		reg = <0x7000e400 0x400>;
 	};
 
-	memory-controller@0x7000f000 {
+	memory-controller@7000f000 {
 		compatible = "nvidia,tegra20-mc";
 		reg = <0x7000f000 0x024
 		       0x7000f03c 0x3c4>;
@@ -183,7 +183,7 @@
 		       0x58000000 0x02000000>;	/* GART aperture */
 	};
 
-	memory-controller@0x7000f400 {
+	memory-controller@7000f400 {
 		compatible = "nvidia,tegra20-emc";
 		reg = <0x7000f400 0x200>;
 		#address-cells = <1>;

arch/arm/common/it8152.c

@@ -284,11 +284,17 @@ int dma_set_coherent_mask(struct device *dev, u64 mask)
 
 int __init it8152_pci_setup(int nr, struct pci_sys_data *sys)
 {
-	it8152_io.start = IT8152_IO_BASE + 0x12000;
-	it8152_io.end	= IT8152_IO_BASE + 0x12000 + 0x100000;
+	/*
+	 * FIXME: use pci_ioremap_io to remap the IO space here and
+	 * move over to the generic io.h implementation.
+	 * This requires solving the same problem for PXA PCMCIA
+	 * support.
+	 */
+	it8152_io.start = (unsigned long)IT8152_IO_BASE + 0x12000;
+	it8152_io.end	= (unsigned long)IT8152_IO_BASE + 0x12000 + 0x100000;
 
 	sys->mem_offset = 0x10000000;
-	sys->io_offset  = IT8152_IO_BASE;
+	sys->io_offset  = (unsigned long)IT8152_IO_BASE;
 
 	if (request_resource(&ioport_resource, &it8152_io)) {
 		printk(KERN_ERR "PCI: unable to allocate IO region\n");

arch/arm/mach-at91/pm.c

@@ -153,7 +153,9 @@ static int at91_pm_verify_clocks(void)
 		}
 	}
 
-#ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS
+	if (!IS_ENABLED(CONFIG_AT91_PROGRAMMABLE_CLOCKS))
+		return 1;
+
 	/* PCK0..PCK3 must be disabled, or configured to use clk32k */
 	for (i = 0; i < 4; i++) {
 		u32 css;
@@ -167,7 +169,6 @@ static int at91_pm_verify_clocks(void)
 			return 0;
 		}
 	}
-#endif
 
 	return 1;
 }

arch/arm/mach-at91/setup.c

@@ -87,7 +87,7 @@ void __init at91_init_sram(int bank, unsigned long base, unsigned int length)
 	iotable_init(desc, 1);
 }
 
-static struct map_desc at91_io_desc __initdata = {
+static struct map_desc at91_io_desc __initdata __maybe_unused = {
 	.virtual	= (unsigned long)AT91_VA_BASE_SYS,
 	.pfn		= __phys_to_pfn(AT91_BASE_SYS),
 	.length		= SZ_16K,

arch/arm/mach-davinci/da850.c

@@ -939,7 +939,7 @@ static struct platform_device da850_cpufreq_device = {
 
 unsigned int da850_max_speed = 300000;
 
-int __init da850_register_cpufreq(char *async_clk)
+int da850_register_cpufreq(char *async_clk)
 {
 	int i;
 

arch/arm/mach-footbridge/include/mach/irqs.h

@@ -89,8 +89,6 @@
 #define IRQ_NETWINDER_VGA	_ISA_IRQ(11)
 #define IRQ_NETWINDER_SOUND	_ISA_IRQ(12)
 
-#undef RTC_IRQ
-#define RTC_IRQ		IRQ_ISA_RTC_ALARM
 #define I8042_KBD_IRQ	IRQ_ISA_KEYBOARD
 #define I8042_AUX_IRQ	(machine_is_netwinder() ? IRQ_NETWINDER_PS2MOUSE : IRQ_ISA_PS2MOUSE)
 #define IRQ_FLOPPYDISK	IRQ_ISA_FLOPPY