mcp23s08 spi gpio expander support

Basic driver for 8-bit SPI based MCP23S08 GPIO expander, without support for
IRQs or the shared chipselect mechanism.

Signed-off-by: David Brownell <[email protected]>
Cc: Jean Delvare <[email protected]>
Cc: Eric Miao <[email protected]>
Cc: Sam Ravnborg <[email protected]>
Cc: Haavard Skinnemoen <[email protected]>
Cc: Philipp Zabel <[email protected]>
Cc: Russell King <[email protected]>
Cc: Ben Gardner <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>

drivers/gpio/Kconfig

@@ -52,4 +52,11 @@ config GPIO_PCF857X
 
 comment "SPI GPIO expanders:"
 
+config GPIO_MCP23S08
+	tristate "Microchip MCP23S08 I/O expander"
+	depends on SPI_MASTER
+	help
+	  SPI driver for Microchip MCP23S08 I/O expander.  This provides
+	  a GPIO interface supporting inputs and outputs.
+
 endmenu

drivers/gpio/Makefile

@@ -4,4 +4,5 @@ ccflags-$(CONFIG_DEBUG_GPIO)	+= -DDEBUG
 
 obj-$(CONFIG_HAVE_GPIO_LIB)	+= gpiolib.o
 
+obj-$(CONFIG_GPIO_MCP23S08)	+= mcp23s08.o
 obj-$(CONFIG_GPIO_PCF857X)	+= pcf857x.o

drivers/gpio/mcp23s08.c

@@ -0,0 +1,357 @@
+/*
+ * mcp23s08.c - SPI gpio expander driver
+ */
+
+#include <linux/kernel.h>
+#include <linux/device.h>
+#include <linux/workqueue.h>
+#include <linux/mutex.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/mcp23s08.h>
+
+#include <asm/gpio.h>
+
+
+/* Registers are all 8 bits wide.
+ *
+ * The mcp23s17 has twice as many bits, and can be configured to work
+ * with either 16 bit registers or with two adjacent 8 bit banks.
+ *
+ * Also, there are I2C versions of both chips.
+ */
+#define MCP_IODIR	0x00		/* init/reset:  all ones */
+#define MCP_IPOL	0x01
+#define MCP_GPINTEN	0x02
+#define MCP_DEFVAL	0x03
+#define MCP_INTCON	0x04
+#define MCP_IOCON	0x05
+#	define IOCON_SEQOP	(1 << 5)
+#	define IOCON_HAEN	(1 << 3)
+#	define IOCON_ODR	(1 << 2)
+#	define IOCON_INTPOL	(1 << 1)
+#define MCP_GPPU	0x06
+#define MCP_INTF	0x07
+#define MCP_INTCAP	0x08
+#define MCP_GPIO	0x09
+#define MCP_OLAT	0x0a
+
+struct mcp23s08 {
+	struct spi_device	*spi;
+	u8			addr;
+
+	/* lock protects the cached values */
+	struct mutex		lock;
+	u8			cache[11];
+
+	struct gpio_chip	chip;
+
+	struct work_struct	work;
+};
+
+static int mcp23s08_read(struct mcp23s08 *mcp, unsigned reg)
+{
+	u8	tx[2], rx[1];
+	int	status;
+
+	tx[0] = mcp->addr | 0x01;
+	tx[1] = reg;
+	status = spi_write_then_read(mcp->spi, tx, sizeof tx, rx, sizeof rx);
+	return (status < 0) ? status : rx[0];
+}
+
+static int mcp23s08_write(struct mcp23s08 *mcp, unsigned reg, u8 val)
+{
+	u8	tx[3];
+
+	tx[0] = mcp->addr;
+	tx[1] = reg;
+	tx[2] = val;
+	return spi_write_then_read(mcp->spi, tx, sizeof tx, NULL, 0);
+}
+
+static int
+mcp23s08_read_regs(struct mcp23s08 *mcp, unsigned reg, u8 *vals, unsigned n)
+{
+	u8	tx[2];
+
+	if ((n + reg) > sizeof mcp->cache)
+		return -EINVAL;
+	tx[0] = mcp->addr | 0x01;
+	tx[1] = reg;
+	return spi_write_then_read(mcp->spi, tx, sizeof tx, vals, n);
+}
+
+/*----------------------------------------------------------------------*/
+
+static int mcp23s08_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+	struct mcp23s08	*mcp = container_of(chip, struct mcp23s08, chip);
+	int status;
+
+	mutex_lock(&mcp->lock);
+	mcp->cache[MCP_IODIR] |= (1 << offset);
+	status = mcp23s08_write(mcp, MCP_IODIR, mcp->cache[MCP_IODIR]);
+	mutex_unlock(&mcp->lock);
+	return status;
+}
+
+static int mcp23s08_get(struct gpio_chip *chip, unsigned offset)
+{
+	struct mcp23s08	*mcp = container_of(chip, struct mcp23s08, chip);
+	int status;
+
+	mutex_lock(&mcp->lock);
+
+	/* REVISIT reading this clears any IRQ ... */
+	status = mcp23s08_read(mcp, MCP_GPIO);
+	if (status < 0)
+		status = 0;
+	else {
+		mcp->cache[MCP_GPIO] = status;
+		status = !!(status & (1 << offset));
+	}
+	mutex_unlock(&mcp->lock);
+	return status;
+}
+
+static int __mcp23s08_set(struct mcp23s08 *mcp, unsigned mask, int value)
+{
+	u8 olat = mcp->cache[MCP_OLAT];
+
+	if (value)
+		olat |= mask;
+	else
+		olat &= ~mask;
+	mcp->cache[MCP_OLAT] = olat;
+	return mcp23s08_write(mcp, MCP_OLAT, olat);
+}
+
+static void mcp23s08_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+	struct mcp23s08	*mcp = container_of(chip, struct mcp23s08, chip);
+	u8 mask = 1 << offset;
+
+	mutex_lock(&mcp->lock);
+	__mcp23s08_set(mcp, mask, value);
+	mutex_unlock(&mcp->lock);
+}
+
+static int
+mcp23s08_direction_output(struct gpio_chip *chip, unsigned offset, int value)
+{
+	struct mcp23s08	*mcp = container_of(chip, struct mcp23s08, chip);
+	u8 mask = 1 << offset;
+	int status;
+
+	mutex_lock(&mcp->lock);
+	status = __mcp23s08_set(mcp, mask, value);
+	if (status == 0) {
+		mcp->cache[MCP_IODIR] &= ~mask;
+		status = mcp23s08_write(mcp, MCP_IODIR, mcp->cache[MCP_IODIR]);
+	}
+	mutex_unlock(&mcp->lock);
+	return status;
+}
+
+/*----------------------------------------------------------------------*/
+
+#ifdef CONFIG_DEBUG_FS
+
+#include <linux/seq_file.h>
+
+/*
+ * This shows more info than the generic gpio dump code:
+ * pullups, deglitching, open drain drive.
+ */
+static void mcp23s08_dbg_show(struct seq_file *s, struct gpio_chip *chip)
+{
+	struct mcp23s08	*mcp;
+	char		bank;
+	unsigned	t;
+	unsigned	mask;
+
+	mcp = container_of(chip, struct mcp23s08, chip);
+
+	/* NOTE: we only handle one bank for now ... */
+	bank = '0' + ((mcp->addr >> 1) & 0x3);
+
+	mutex_lock(&mcp->lock);
+	t = mcp23s08_read_regs(mcp, 0, mcp->cache, sizeof mcp->cache);
+	if (t < 0) {
+		seq_printf(s, " I/O ERROR %d\n", t);
+		goto done;
+	}
+
+	for (t = 0, mask = 1; t < 8; t++, mask <<= 1) {
+		const char	*label;
+
+		label = gpiochip_is_requested(chip, t);
+		if (!label)
+			continue;
+
+		seq_printf(s, " gpio-%-3d P%c.%d (%-12s) %s %s %s",
+			chip->base + t, bank, t, label,
+			(mcp->cache[MCP_IODIR] & mask) ? "in " : "out",
+			(mcp->cache[MCP_GPIO] & mask) ? "hi" : "lo",
+			(mcp->cache[MCP_GPPU] & mask) ? "  " : "up");
+		/* NOTE:  ignoring the irq-related registers */
+		seq_printf(s, "\n");
+	}
+done:
+	mutex_unlock(&mcp->lock);
+}
+
+#else
+#define mcp23s08_dbg_show	NULL
+#endif
+
+/*----------------------------------------------------------------------*/
+
+static int mcp23s08_probe(struct spi_device *spi)
+{
+	struct mcp23s08			*mcp;
+	struct mcp23s08_platform_data	*pdata;
+	int				status;
+	int				do_update = 0;
+
+	pdata = spi->dev.platform_data;
+	if (!pdata || pdata->slave > 3 || !pdata->base)
+		return -ENODEV;
+
+	mcp = kzalloc(sizeof *mcp, GFP_KERNEL);
+	if (!mcp)
+		return -ENOMEM;
+
+	mutex_init(&mcp->lock);
+
+	mcp->spi = spi;
+	mcp->addr = 0x40 | (pdata->slave << 1);
+
+	mcp->chip.label = "mcp23s08",
+
+	mcp->chip.direction_input = mcp23s08_direction_input;
+	mcp->chip.get = mcp23s08_get;
+	mcp->chip.direction_output = mcp23s08_direction_output;
+	mcp->chip.set = mcp23s08_set;
+	mcp->chip.dbg_show = mcp23s08_dbg_show;
+
+	mcp->chip.base = pdata->base;
+	mcp->chip.ngpio = 8;
+	mcp->chip.can_sleep = 1;
+
+	spi_set_drvdata(spi, mcp);
+
+	/* verify MCP_IOCON.SEQOP = 0, so sequential reads work */
+	status = mcp23s08_read(mcp, MCP_IOCON);
+	if (status < 0)
+		goto fail;
+	if (status & IOCON_SEQOP) {
+		status &= ~IOCON_SEQOP;
+		status = mcp23s08_write(mcp, MCP_IOCON, (u8) status);
+		if (status < 0)
+			goto fail;
+	}
+
+	/* configure ~100K pullups */
+	status = mcp23s08_write(mcp, MCP_GPPU, pdata->pullups);
+	if (status < 0)
+		goto fail;
+
+	status = mcp23s08_read_regs(mcp, 0, mcp->cache, sizeof mcp->cache);
+	if (status < 0)
+		goto fail;
+
+	/* disable inverter on input */
+	if (mcp->cache[MCP_IPOL] != 0) {
+		mcp->cache[MCP_IPOL] = 0;
+		do_update = 1;
+	}
+
+	/* disable irqs */
+	if (mcp->cache[MCP_GPINTEN] != 0) {
+		mcp->cache[MCP_GPINTEN] = 0;
+		do_update = 1;
+	}
+
+	if (do_update) {
+		u8 tx[4];
+
+		tx[0] = mcp->addr;
+		tx[1] = MCP_IPOL;
+		memcpy(&tx[2], &mcp->cache[MCP_IPOL], sizeof(tx) - 2);
+		status = spi_write_then_read(mcp->spi, tx, sizeof tx, NULL, 0);
+
+		/* FIXME check status... */
+	}
+
+	status = gpiochip_add(&mcp->chip);
+
+	/* NOTE:  these chips have a relatively sane IRQ framework, with
+	 * per-signal masking and level/edge triggering.  It's not yet
+	 * handled here...
+	 */
+
+	if (pdata->setup) {
+		status = pdata->setup(spi, mcp->chip.base,
+				mcp->chip.ngpio, pdata->context);
+		if (status < 0)
+			dev_dbg(&spi->dev, "setup --> %d\n", status);
+	}
+
+	return 0;
+
+fail:
+	kfree(mcp);
+	return status;
+}
+
+static int mcp23s08_remove(struct spi_device *spi)
+{
+	struct mcp23s08			*mcp = spi_get_drvdata(spi);
+	struct mcp23s08_platform_data	*pdata = spi->dev.platform_data;
+	int				status = 0;
+
+	if (pdata->teardown) {
+		status = pdata->teardown(spi,
+				mcp->chip.base, mcp->chip.ngpio,
+				pdata->context);
+		if (status < 0) {
+			dev_err(&spi->dev, "%s --> %d\n", "teardown", status);
+			return status;
+		}
+	}
+
+	status = gpiochip_remove(&mcp->chip);
+	if (status == 0)
+		kfree(mcp);
+	else
+		dev_err(&spi->dev, "%s --> %d\n", "remove", status);
+	return status;
+}
+
+static struct spi_driver mcp23s08_driver = {
+	.probe		= mcp23s08_probe,
+	.remove		= mcp23s08_remove,
+	.driver = {
+		.name	= "mcp23s08",
+		.owner	= THIS_MODULE,
+	},
+};
+
+/*----------------------------------------------------------------------*/
+
+static int __init mcp23s08_init(void)
+{
+	return spi_register_driver(&mcp23s08_driver);
+}
+module_init(mcp23s08_init);
+
+static void __exit mcp23s08_exit(void)
+{
+	spi_unregister_driver(&mcp23s08_driver);
+}
+module_exit(mcp23s08_exit);
+
+MODULE_LICENSE("GPL");
+