Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel…

…/git/arm/arm-soc

Pull ARM SoC DT updates from Olof Johansson:
 "Most of this branch consists of updates, additions and general churn
  of the device tree source files in the kernel (arch/arm/boot/dts).
  Besides that, there are a few things to point out:

   - Lots of platform conversion on OMAP2+, with removal of old board
     files for various platforms.
   - Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
     well
   - Some updates to pinctrl and other subsystems.  Most of these are
     for DT-enablement of the various platforms and acks have been
     collected"

* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
  ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
  ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
  ARM: dts: bcm281xx: Add card detect GPIO
  ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
  ARM: bcm281xx: Add device node for the GPIO controller
  ARM: mvebu: Add Netgear ReadyNAS 104 board
  ARM: tegra: fix Tegra114 IOMMU register address
  ARM: kirkwood: add support for OpenBlocks A7 platform
  ARM: dts: omap4-panda: add DPI pinmuxing
  ARM: dts: AM33xx: Add RNG node
  ARM: dts: AM33XX: Add hwspinlock node
  ARM: dts: OMAP5: Add hwspinlock node
  ARM: dts: OMAP4: Add hwspinlock node
  ARM: dts: use 'status' property for PCIe nodes
  ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
  ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
  ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
  ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
  ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
  ARM: mvebu: Add the core-divider clock to Armada 370/XP
  ...

Documentation/devicetree/bindings/arm/omap/omap.txt

@@ -21,7 +21,8 @@ Required properties:
 Optional properties:
 - ti,no_idle_on_suspend: When present, it prevents the PM to idle the module
   during suspend.
-
+- ti,no-reset-on-init: When present, the module should not be reset at init
+- ti,no-idle-on-init: When present, the module should not be idled at init
 
 Example:
 

Documentation/devicetree/bindings/arm/vic.txt

@@ -18,6 +18,15 @@ Required properties:
 Optional properties:
 
 - interrupts : Interrupt source for parent controllers if the VIC is nested.
+- valid-mask : A one cell big bit mask of valid interrupt sources. Each bit
+  represents single interrupt source, starting from source 0 at LSb and ending
+  at source 31 at MSb. A bit that is set means that the source is wired and
+  clear means otherwise. If unspecified, defaults to all valid.
+- valid-wakeup-mask : A one cell big bit mask of interrupt sources that can be
+  configured as wake up source for the system. Order of bits is the same as for
+  valid-mask property. A set bit means that this interrupt source can be
+  configured as a wake up source for the system. If unspecied, defaults to all
+  interrupt sources configurable as wake up sources.
 
 Example:
 
@@ -26,4 +35,7 @@ Example:
 		interrupt-controller;
 		#interrupt-cells = <1>;
 		reg = <0x60000 0x1000>;
+
+		valid-mask = <0xffffff7f>;
+		valid-wakeup-mask = <0x0000ff7f>;
 	};

Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt

@@ -0,0 +1,19 @@
+* Core Divider Clock bindings for Marvell MVEBU SoCs
+
+The following is a list of provided IDs and clock names on Armada 370/XP:
+ 0 = nand (NAND clock)
+
+Required properties:
+- compatible : must be "marvell,armada-370-corediv-clock"
+- reg : must be the register address of Core Divider control register
+- #clock-cells : from common clock binding; shall be set to 1
+- clocks : must be set to the parent's phandle
+
+Example:
+
+corediv_clk: corediv-clocks@18740 {
+	compatible = "marvell,armada-370-corediv-clock";
+	reg = <0x18740 0xc>;
+	#clock-cells = <1>;
+	clocks = <&pll>;
+};

Documentation/devicetree/bindings/crypto/omap-aes.txt

@@ -0,0 +1,31 @@
+OMAP SoC AES crypto Module
+
+Required properties:
+
+- compatible : Should contain entries for this and backward compatible
+  AES versions:
+  - "ti,omap2-aes" for OMAP2.
+  - "ti,omap3-aes" for OMAP3.
+  - "ti,omap4-aes" for OMAP4 and AM33XX.
+  Note that the OMAP2 and 3 versions are compatible (OMAP3 supports
+  more algorithms) but they are incompatible with OMAP4.
+- ti,hwmods: Name of the hwmod associated with the AES module
+- reg : Offset and length of the register set for the module
+- interrupts : the interrupt-specifier for the AES module.
+
+Optional properties:
+- dmas: DMA specifiers for tx and rx dma. See the DMA client binding,
+	Documentation/devicetree/bindings/dma/dma.txt
+- dma-names: DMA request names should include "tx" and "rx" if present.
+
+Example:
+	/* AM335x */
+	aes: aes@53500000 {
+		compatible = "ti,omap4-aes";
+		ti,hwmods = "aes";
+		reg = <0x53500000 0xa0>;
+		interrupts = <102>;
+		dmas = <&edma 6>,
+		       <&edma 5>;
+		dma-names = "tx", "rx";
+	};

Documentation/devicetree/bindings/crypto/omap-sham.txt

@@ -0,0 +1,28 @@
+OMAP SoC SHA crypto Module
+
+Required properties:
+
+- compatible : Should contain entries for this and backward compatible
+  SHAM versions:
+  - "ti,omap2-sham" for OMAP2 & OMAP3.
+  - "ti,omap4-sham" for OMAP4 and AM33XX.
+  Note that these two versions are incompatible.
+- ti,hwmods: Name of the hwmod associated with the SHAM module
+- reg : Offset and length of the register set for the module
+- interrupts : the interrupt-specifier for the SHAM module.
+
+Optional properties:
+- dmas: DMA specifiers for the rx dma. See the DMA client binding,
+	Documentation/devicetree/bindings/dma/dma.txt
+- dma-names: DMA request name. Should be "rx" if a dma is present.
+
+Example:
+	/* AM335x */
+	sham: sham@53100000 {
+		compatible = "ti,omap4-sham";
+		ti,hwmods = "sham";
+		reg = <0x53100000 0x200>;
+		interrupts = <109>;
+		dmas = <&edma 36>;
+		dma-names = "rx";
+	};

Documentation/devicetree/bindings/hwrng/omap_rng.txt

@@ -0,0 +1,22 @@
+OMAP SoC HWRNG Module
+
+Required properties:
+
+- compatible : Should contain entries for this and backward compatible
+  RNG versions:
+  - "ti,omap2-rng" for OMAP2.
+  - "ti,omap4-rng" for OMAP4, OMAP5 and AM33XX.
+  Note that these two versions are incompatible.
+- ti,hwmods: Name of the hwmod associated with the RNG module
+- reg : Offset and length of the register set for the module
+- interrupts : the interrupt number for the RNG module.
+		Only used for "ti,omap4-rng".
+
+Example:
+/* AM335x */
+rng: rng@48310000 {
+	compatible = "ti,omap4-rng";
+	ti,hwmods = "rng";
+	reg = <0x48310000 0x2000>;
+	interrupts = <111>;
+};

Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt

@@ -20,8 +20,29 @@ ti,dual-volt: boolean, supports dual voltage cards
 ti,non-removable: non-removable slot (like eMMC)
 ti,needs-special-reset: Requires a special softreset sequence
 ti,needs-special-hs-handling: HSMMC IP needs special setting for handling High Speed
+dmas: List of DMA specifiers with the controller specific format
+as described in the generic DMA client binding. A tx and rx
+specifier is required.
+dma-names: List of DMA request names. These strings correspond
+1:1 with the DMA specifiers listed in dmas. The string naming is
+to be "rx" and "tx" for RX and TX DMA requests, respectively.
+
+Examples:
+
+[hwmod populated DMA resources]
+
+	mmc1: mmc@0x4809c000 {
+		compatible = "ti,omap4-hsmmc";
+		reg = <0x4809c000 0x400>;
+		ti,hwmods = "mmc1";
+		ti,dual-volt;
+		bus-width = <4>;
+		vmmc-supply = <&vmmc>; /* phandle to regulator node */
+		ti,non-removable;
+	};
+
+[generic DMA request binding]
 
-Example:
 	mmc1: mmc@0x4809c000 {
 		compatible = "ti,omap4-hsmmc";
 		reg = <0x4809c000 0x400>;
@@ -30,4 +51,7 @@ Example:
 		bus-width = <4>;
 		vmmc-supply = <&vmmc>; /* phandle to regulator node */
 		ti,non-removable;
+		dmas = <&edma 24
+			&edma 25>;
+		dma-names = "tx", "rx";
 	};