Merge 3.18-rc7 into usb-next

We need the xhci fixes here and this resolves a merge issue with
drivers/usb/dwc3/ep0.c

Signed-off-by: Greg Kroah-Hartman <[email protected]>

Documentation/devicetree/bindings/ata/sata_rcar.txt

@@ -3,8 +3,10 @@
 Required properties:
 - compatible		: should contain one of the following:
 			  - "renesas,sata-r8a7779" for R-Car H1
-			  - "renesas,sata-r8a7790" for R-Car H2
-			  - "renesas,sata-r8a7791" for R-Car M2
+			  - "renesas,sata-r8a7790-es1" for R-Car H2 ES1
+			  - "renesas,sata-r8a7790" for R-Car H2 other than ES1
+			  - "renesas,sata-r8a7791" for R-Car M2-W
+			  - "renesas,sata-r8a7793" for R-Car M2-N
 - reg			: address and length of the SATA registers;
 - interrupts		: must consist of one interrupt specifier.
 

Documentation/devicetree/bindings/interrupt-controller/interrupts.txt

@@ -30,10 +30,6 @@ should only be used when a device has multiple interrupt parents.
   Example:
 	interrupts-extended = <&intc1 5 1>, <&intc2 1 0>;
 
-A device node may contain either "interrupts" or "interrupts-extended", but not
-both. If both properties are present, then the operating system should log an
-error and use only the data in "interrupts".
-
 2) Interrupt controller nodes
 -----------------------------
 

Documentation/devicetree/bindings/pci/pci.txt

@@ -7,3 +7,14 @@ And for the interrupt mapping part:
 
 Open Firmware Recommended Practice: Interrupt Mapping
 http://www.openfirmware.org/1275/practice/imap/imap0_9d.pdf
+
+Additionally to the properties specified in the above standards a host bridge
+driver implementation may support the following properties:
+
+- linux,pci-domain:
+   If present this property assigns a fixed PCI domain number to a host bridge,
+   otherwise an unstable (across boots) unique number will be assigned.
+   It is required to either not set this property at all or set it for all
+   host bridges in the system, otherwise potentially conflicting domain numbers
+   may be assigned to root buses behind different host bridges.  The domain
+   number for each host bridge in the system must be unique.

Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt

@@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the
 common pinctrl bindings used by client devices, including the meaning of the
 phrase "pin configuration node".
 
-TZ1090-PDC's pin configuration nodes act as a container for an abitrary number
+TZ1090-PDC's pin configuration nodes act as a container for an arbitrary number
 of subnodes. Each of these subnodes represents some desired configuration for a
 pin, a group, or a list of pins or groups. This configuration can include the
 mux function to select on those pin(s)/group(s), and various pin configuration

Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt

@@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the
 common pinctrl bindings used by client devices, including the meaning of the
 phrase "pin configuration node".
 
-TZ1090's pin configuration nodes act as a container for an abitrary number of
+TZ1090's pin configuration nodes act as a container for an arbitrary number of
 subnodes. Each of these subnodes represents some desired configuration for a
 pin, a group, or a list of pins or groups. This configuration can include the
 mux function to select on those pin(s)/group(s), and various pin configuration

Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt

@@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the
 common pinctrl bindings used by client devices, including the meaning of the
 phrase "pin configuration node".
 
-Lantiq's pin configuration nodes act as a container for an abitrary number of
+Lantiq's pin configuration nodes act as a container for an arbitrary number of
 subnodes. Each of these subnodes represents some desired configuration for a
 pin, a group, or a list of pins or groups. This configuration can include the
 mux function to select on those group(s), and two pin configuration parameters:

Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt

@@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the
 common pinctrl bindings used by client devices, including the meaning of the
 phrase "pin configuration node".
 
-Lantiq's pin configuration nodes act as a container for an abitrary number of
+Lantiq's pin configuration nodes act as a container for an arbitrary number of
 subnodes. Each of these subnodes represents some desired configuration for a
 pin, a group, or a list of pins or groups. This configuration can include the
 mux function to select on those group(s), and two pin configuration parameters:

Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt

@@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the
 common pinctrl bindings used by client devices, including the meaning of the
 phrase "pin configuration node".
 
-Tegra's pin configuration nodes act as a container for an abitrary number of
+Tegra's pin configuration nodes act as a container for an arbitrary number of
 subnodes. Each of these subnodes represents some desired configuration for a
 pin, a group, or a list of pins or groups. This configuration can include the
 mux function to select on those pin(s)/group(s), and various pin configuration

Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt

@@ -13,7 +13,7 @@ Optional properties:
 Please refer to pinctrl-bindings.txt in this directory for details of the common
 pinctrl bindings used by client devices.
 
-SiRFprimaII's pinmux nodes act as a container for an abitrary number of subnodes.
+SiRFprimaII's pinmux nodes act as a container for an arbitrary number of subnodes.
 Each of these subnodes represents some desired configuration for a group of pins.
 
 Required subnode-properties:

Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt

@@ -32,7 +32,7 @@ Required properties:
 Please refer to pinctrl-bindings.txt in this directory for details of the common
 pinctrl bindings used by client devices.
 
-SPEAr's pinmux nodes act as a container for an abitrary number of subnodes. Each
+SPEAr's pinmux nodes act as a container for an arbitrary number of subnodes. Each
 of these subnodes represents muxing for a pin, a group, or a list of pins or
 groups.
 

Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt

@@ -18,7 +18,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the
 common pinctrl bindings used by client devices, including the meaning of the
 phrase "pin configuration node".
 
-Qualcomm's pin configuration nodes act as a container for an abitrary number of
+Qualcomm's pin configuration nodes act as a container for an arbitrary number of
 subnodes. Each of these subnodes represents some desired configuration for a
 pin, a group, or a list of pins or groups. This configuration can include the
 mux function to select on those pin(s)/group(s), and various pin configuration

Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt

@@ -47,7 +47,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the
 common pinctrl bindings used by client devices, including the meaning of the
 phrase "pin configuration node".
 
-The pin configuration nodes act as a container for an abitrary number of
+The pin configuration nodes act as a container for an arbitrary number of
 subnodes. Each of these subnodes represents some desired configuration for a
 pin, a group, or a list of pins or groups. This configuration can include the
 mux function to select on those pin(s)/group(s), and various pin configuration

Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt

@@ -18,7 +18,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the
 common pinctrl bindings used by client devices, including the meaning of the
 phrase "pin configuration node".
 
-Qualcomm's pin configuration nodes act as a container for an abitrary number of
+Qualcomm's pin configuration nodes act as a container for an arbitrary number of
 subnodes. Each of these subnodes represents some desired configuration for a
 pin, a group, or a list of pins or groups. This configuration can include the
 mux function to select on those pin(s)/group(s), and various pin configuration

Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt

@@ -47,7 +47,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the
 common pinctrl bindings used by client devices, including the meaning of the
 phrase "pin configuration node".
 
-The pin configuration nodes act as a container for an abitrary number of
+The pin configuration nodes act as a container for an arbitrary number of
 subnodes. Each of these subnodes represents some desired configuration for a
 pin, a group, or a list of pins or groups. This configuration can include the
 mux function to select on those pin(s)/group(s), and various pin configuration

Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt

@@ -18,7 +18,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the
 common pinctrl bindings used by client devices, including the meaning of the
 phrase "pin configuration node".
 
-Qualcomm's pin configuration nodes act as a container for an abitrary number of
+Qualcomm's pin configuration nodes act as a container for an arbitrary number of
 subnodes. Each of these subnodes represents some desired configuration for a
 pin, a group, or a list of pins or groups. This configuration can include the
 mux function to select on those pin(s)/group(s), and various pin configuration

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -34,6 +34,7 @@ chipidea	Chipidea, Inc
 chrp	Common Hardware Reference Platform
 chunghwa	Chunghwa Picture Tubes Ltd.
 cirrus	Cirrus Logic, Inc.
+cnm	Chips&Media, Inc.
 cortina	Cortina Systems, Inc.
 crystalfontz	Crystalfontz America, Inc.
 dallas	Maxim Integrated Products (formerly Dallas Semiconductor)
@@ -92,6 +93,7 @@ maxim	Maxim Integrated Products
 mediatek	MediaTek Inc.
 micrel	Micrel Inc.
 microchip	Microchip Technology Inc.
+micron	Micron Technology Inc.
 mitsubishi	Mitsubishi Electric Corporation
 mosaixtech	Mosaix Technologies, Inc.
 moxa	Moxa
@@ -127,6 +129,7 @@ renesas	Renesas Electronics Corporation
 ricoh	Ricoh Co. Ltd.
 rockchip	Fuzhou Rockchip Electronics Co., Ltd
 samsung	Samsung Semiconductor
+sandisk	Sandisk Corporation
 sbs	Smart Battery System
 schindler	Schindler
 seagate	Seagate Technology PLC
@@ -138,7 +141,7 @@ silergy	Silergy Corp.
 sirf	SiRF Technology, Inc.
 sitronix	Sitronix Technology Corporation
 smsc	Standard Microsystems Corporation
-snps 	Synopsys, Inc.
+snps	Synopsys, Inc.
 solidrun	SolidRun
 sony	Sony Corporation
 spansion	Spansion Inc.

Documentation/filesystems/overlayfs.txt

@@ -64,7 +64,7 @@ is formed.
 At mount time, the two directories given as mount options "lowerdir" and
 "upperdir" are combined into a merged directory:
 
-  mount -t overlayfs overlayfs -olowerdir=/lower,upperdir=/upper,\
+  mount -t overlay overlay -olowerdir=/lower,upperdir=/upper,\
 workdir=/work /merged
 
 The "workdir" needs to be an empty directory on the same filesystem

Documentation/input/elantech.txt

@@ -38,22 +38,38 @@ Contents
         7.2.1 Status packet
         7.2.2 Head packet
         7.2.3 Motion packet
+ 8. Trackpoint (for Hardware version 3 and 4)
+    8.1 Registers
+    8.2 Native relative mode 6 byte packet format
+        8.2.1 Status Packet
 
 
 
 1. Introduction
    ~~~~~~~~~~~~
 
-Currently the Linux Elantech touchpad driver is aware of two different
-hardware versions unimaginatively called version 1 and version 2. Version 1
-is found in "older" laptops and uses 4 bytes per packet. Version 2 seems to
-be introduced with the EeePC and uses 6 bytes per packet, and provides
-additional features such as position of two fingers, and width of the touch.
+Currently the Linux Elantech touchpad driver is aware of four different
+hardware versions unimaginatively called version 1,version 2, version 3
+and version 4. Version 1 is found in "older" laptops and uses 4 bytes per
+packet. Version 2 seems to be introduced with the EeePC and uses 6 bytes
+per packet, and provides additional features such as position of two fingers,
+and width of the touch.  Hardware version 3 uses 6 bytes per packet (and
+for 2 fingers the concatenation of two 6 bytes packets) and allows tracking
+of up to 3 fingers. Hardware version 4 uses 6 bytes per packet, and can
+combine a status packet with multiple head or motion packets. Hardware version
+4 allows tracking up to 5 fingers.
+
+Some Hardware version 3 and version 4 also have a trackpoint which uses a
+separate packet format. It is also 6 bytes per packet.
 
 The driver tries to support both hardware versions and should be compatible
 with the Xorg Synaptics touchpad driver and its graphical configuration
 utilities.
 
+Note that a mouse button is also associated with either the touchpad or the
+trackpoint when a trackpoint is available.  Disabling the Touchpad in xorg
+(TouchPadOff=0) will also disable the buttons associated with the touchpad.
+
 Additionally the operation of the touchpad can be altered by adjusting the
 contents of some of its internal registers. These registers are represented
 by the driver as sysfs entries under /sys/bus/serio/drivers/psmouse/serio?
@@ -78,7 +94,7 @@ completeness sake.
 2. Extra knobs
    ~~~~~~~~~~~
 
-Currently the Linux Elantech touchpad driver provides two extra knobs under
+Currently the Linux Elantech touchpad driver provides three extra knobs under
 /sys/bus/serio/drivers/psmouse/serio? for the user.
 
 * debug
@@ -112,6 +128,20 @@ Currently the Linux Elantech touchpad driver provides two extra knobs under
    data consistency checking can be done. For now checking is disabled by
    default. Currently even turning it on will do nothing.
 
+* crc_enabled
+
+   Sets crc_enabled to 0/1. The name "crc_enabled" is the official name of
+   this integrity check, even though it is not an actual cyclic redundancy
+   check.
+
+   Depending on the state of crc_enabled, certain basic data integrity
+   verification is done by the driver on hardware version 3 and 4. The
+   driver will reject any packet that appears corrupted. Using this knob,
+   The state of crc_enabled can be altered with this knob.
+
+   Reading the crc_enabled value will show the active value. Echoing
+   "0" or "1" to this file will set the state to "0" or "1".
+
 /////////////////////////////////////////////////////////////////////////////
 
 3. Differentiating hardware versions
@@ -746,3 +776,42 @@ byte 5:
 
         byte 0 ~ 2 for one finger
         byte 3 ~ 5 for another
+
+
+8. Trackpoint (for Hardware version 3 and 4)
+   =========================================
+8.1 Registers
+    ~~~~~~~~~
+No special registers have been identified.
+
+8.2 Native relative mode 6 byte packet format
+    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+8.2.1 Status Packet
+      ~~~~~~~~~~~~~
+
+byte 0:
+   bit   7   6   5   4   3   2   1   0
+         0   0  sx  sy   0   M   R   L
+byte 1:
+   bit   7   6   5   4   3   2   1   0
+       ~sx   0   0   0   0   0   0   0
+byte 2:
+   bit   7   6   5   4   3   2   1   0
+       ~sy   0   0   0   0   0   0   0
+byte 3:
+   bit   7   6   5   4   3   2   1   0
+         0   0 ~sy ~sx   0   1   1   0
+byte 4:
+   bit   7   6   5   4   3   2   1   0
+        x7  x6  x5  x4  x3  x2  x1  x0
+byte 5:
+   bit   7   6   5   4   3   2   1   0
+        y7  y6  y5  y4  y3  y2  y1  y0
+
+
+         x and y are written in two's complement spread
+             over 9 bits with sx/sy the relative top bit and
+             x7..x0 and y7..y0 the lower bits.
+	 ~sx is the inverse of sx, ~sy is the inverse of sy.
+         The sign of y is opposite to what the input driver
+             expects for a relative movement

Documentation/networking/ip-sysctl.txt

@@ -56,6 +56,13 @@ ip_forward_use_pmtu - BOOLEAN
 	0 - disabled
 	1 - enabled
 
+fwmark_reflect - BOOLEAN
+	Controls the fwmark of kernel-generated IPv4 reply packets that are not
+	associated with a socket for example, TCP RSTs or ICMP echo replies).
+	If unset, these packets have a fwmark of zero. If set, they have the
+	fwmark of the packet they are replying to.
+	Default: 0
+
 route/max_size - INTEGER
 	Maximum number of routes allowed in the kernel.  Increase
 	this when using large numbers of interfaces and/or routes.
@@ -1201,6 +1208,13 @@ conf/all/forwarding - BOOLEAN
 proxy_ndp - BOOLEAN
 	Do proxy ndp.
 
+fwmark_reflect - BOOLEAN
+	Controls the fwmark of kernel-generated IPv6 reply packets that are not
+	associated with a socket for example, TCP RSTs or ICMPv6 echo replies).
+	If unset, these packets have a fwmark of zero. If set, they have the
+	fwmark of the packet they are replying to.
+	Default: 0
+
 conf/interface/*:
 	Change special settings per interface.
 

Documentation/networking/timestamping.txt

@@ -136,7 +136,7 @@ SOF_TIMESTAMPING_OPT_ID:
 
   This option is implemented only for transmit timestamps. There, the
   timestamp is always looped along with a struct sock_extended_err.
-  The option modifies field ee_info to pass an id that is unique
+  The option modifies field ee_data to pass an id that is unique
   among all possibly concurrently outstanding timestamp requests for
   that socket. In practice, it is a monotonically increasing u32
   (that wraps).