Cleanup rules.mk for 32U4 keyboards, A-F (qmk#6804)

* Cleanup rules.mk for 32U4 keyboards, A-F

* Put back stuff in VIA keymaps

keyboards/abstract/ellipse/rev1/rules.mk

@@ -1,63 +1,16 @@
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
 # Build Options
 #   change yes to no to disable
 #

keyboards/acr60/rules.mk

@@ -1,45 +1,15 @@
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = atmel-dfu
 
 # Build Options
 #   comment out to disable the options.
@@ -53,4 +23,4 @@ SLEEP_LED_ENABLE = no  # Breathing sleep LED during USB suspend
 NKRO_ENABLE = yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
 BACKLIGHT_ENABLE = yes  # Enable keyboard backlight functionality
 AUDIO_ENABLE = no
-RGBLIGHT_ENABLE = yes
+RGBLIGHT_ENABLE = yes

keyboards/adkb96/rules.mk

@@ -1,58 +1,16 @@
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
- # Bootloader selection 
- #   Teensy       halfkay 
- #   Pro Micro    caterina 
- #   Atmel DFU    atmel-dfu 
- #   LUFA DFU     lufa-dfu 
- #   QMK DFU      qmk-dfu 
- #   atmega32a    bootloadHID 
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = caterina
 
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
 # Build Options
 #   change to "no" to disable the options, or define them in the Makefile in
 #   the appropriate keymap folder that will get included automatically

keyboards/aeboards/aegis/keymaps/via/rules.mk

@@ -1,6 +1,6 @@
 # project specific files
 SRC =	keyboards/wilba_tech/wt_main.c
-		
+
 # MCU name
 MCU = atmega32u4
 
@@ -65,4 +65,4 @@ AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 
 RAW_ENABLE = yes
-DYNAMIC_KEYMAP_ENABLE = yes
+DYNAMIC_KEYMAP_ENABLE = yes

keyboards/aeboards/aegis/rules.mk

@@ -1,50 +1,16 @@
-# project specific files
-SRC =	keyboards/wilba_tech/wt_main.c
-
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-
 # Build Options
 #   change yes to no to disable
 #
@@ -63,3 +29,6 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+
+# project specific files
+SRC = keyboards/wilba_tech/wt_main.c

keyboards/aeboards/ext65/keymaps/via/rules.mk

@@ -1,6 +1,6 @@
 # project specific files
 SRC =	keyboards/wilba_tech/wt_main.c
-		
+
 # MCU name
 MCU = atmega32u4
 
@@ -65,4 +65,4 @@ AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 
 RAW_ENABLE = yes
-DYNAMIC_KEYMAP_ENABLE = yes
+DYNAMIC_KEYMAP_ENABLE = yes

keyboards/aeboards/ext65/rules.mk

@@ -1,50 +1,16 @@
-# project specific files
-SRC =	keyboards/wilba_tech/wt_main.c
-
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-
 # Build Options
 #   change yes to no to disable
 #
@@ -63,3 +29,6 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+
+# project specific files
+SRC += keyboards/wilba_tech/wt_main.c