Merge tag 'net-5.11-rc3-2' of git://git.kernel.org/pub/scm/linux/kern…

…el/git/netdev/net

Pull more networking fixes from Jakub Kicinski:
 "Slightly lighter pull request to get back into the Thursday cadence.

  Current release - always broken:

   - can: mcp251xfd: fix Tx/Rx ring buffer driver race conditions

   - dsa: hellcreek: fix led_classdev build errors

  Previous releases - regressions:

   - ipv6: fib: flush exceptions when purging route to avoid netdev
     reference leak

   - ip_tunnels: fix pmtu check in nopmtudisc mode

   - ip: always refragment ip defragmented packets to avoid MTU issues
     when forwarding through tunnels, correct "packet too big" message
     is prohibitively tricky to generate

   - s390/qeth: fix locking for discipline setup / removal and during
     recovery to prevent both deadlocks and races

   - mlx5: Use port_num 1 instead of 0 when delete a RoCE address

  Previous releases - always broken:

   - cdc_ncm: correct overhead calculation in delayed_ndp_size to
     prevent out of bound accesses with Huawei 909s-120 LTE module

   - fix stmmac dwmac-sun8i suspend/resume:
           - PHY being left powered off
           - MAC syscon configuration being reset
           - reference to the reset controller being improperly dropped

   - qrtr: fix null-ptr-deref in qrtr_ns_remove

   - can: tcan4x5x: fix bittiming const, use common bittiming from m_can
     driver

   - mlx5e: CT: Use per flow counter when CT flow accounting is enabled

   - mlx5e: Fix SWP offsets when vlan inserted by driver

  Misc:

   - bpf: Fix a task_iter bug caused by a bpf -> net merge conflict
     resolution

  And the usual many fixes to various error paths"

* tag 'net-5.11-rc3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (69 commits)
  net: dsa: lantiq_gswip: Exclude RMII from modes that report 1 GbE
  s390/qeth: fix L2 header access in qeth_l3_osa_features_check()
  s390/qeth: fix locking for discipline setup / removal
  s390/qeth: fix deadlock during recovery
  selftests: fib_nexthops: Fix wrong mausezahn invocation
  nexthop: Bounce NHA_GATEWAY in FDB nexthop groups
  nexthop: Unlink nexthop group entry in error path
  nexthop: Fix off-by-one error in error path
  octeontx2-af: fix memory leak of lmac and lmac->name
  chtls: Fix chtls resources release sequence
  chtls: Added a check to avoid NULL pointer dereference
  chtls: Replace skb_dequeue with skb_peek
  chtls: Avoid unnecessary freeing of oreq pointer
  chtls: Fix panic when route to peer not configured
  chtls: Remove invalid set_tcb call
  chtls: Fix hardware tid leak
  net: ip: always refragment ip defragmented packets
  net: fix pmtu check in nopmtudisc mode
  selftests: netfilter: add selftest for ipip pmtu discovery with enabled connection tracking
  docs: octeontx2: tune rst markup
  ...

Documentation/networking/device_drivers/ethernet/marvell/octeontx2.rst

@@ -164,46 +164,56 @@ Devlink health reporters
 
 NPA Reporters
 -------------
-The NPA reporters are responsible for reporting and recovering the following group of errors
+The NPA reporters are responsible for reporting and recovering the following group of errors:
+
 1. GENERAL events
+
    - Error due to operation of unmapped PF.
    - Error due to disabled alloc/free for other HW blocks (NIX, SSO, TIM, DPI and AURA).
+
 2. ERROR events
+
    - Fault due to NPA_AQ_INST_S read or NPA_AQ_RES_S write.
    - AQ Doorbell Error.
+
 3. RAS events
+
    - RAS Error Reporting for NPA_AQ_INST_S/NPA_AQ_RES_S.
+
 4. RVU events
+
    - Error due to unmapped slot.
 
-Sample Output
--------------
-~# devlink health
-pci/0002:01:00.0:
-  reporter hw_npa_intr
-      state healthy error 2872 recover 2872 last_dump_date 2020-12-10 last_dump_time 09:39:09 grace_period 0 auto_recover true auto_dump true
-  reporter hw_npa_gen
-      state healthy error 2872 recover 2872 last_dump_date 2020-12-11 last_dump_time 04:43:04 grace_period 0 auto_recover true auto_dump true
-  reporter hw_npa_err
-      state healthy error 2871 recover 2871 last_dump_date 2020-12-10 last_dump_time 09:39:17 grace_period 0 auto_recover true auto_dump true
-   reporter hw_npa_ras
-      state healthy error 0 recover 0 last_dump_date 2020-12-10 last_dump_time 09:32:40 grace_period 0 auto_recover true auto_dump true
+Sample Output::
+
+	~# devlink health
+	pci/0002:01:00.0:
+	  reporter hw_npa_intr
+	      state healthy error 2872 recover 2872 last_dump_date 2020-12-10 last_dump_time 09:39:09 grace_period 0 auto_recover true auto_dump true
+	  reporter hw_npa_gen
+	      state healthy error 2872 recover 2872 last_dump_date 2020-12-11 last_dump_time 04:43:04 grace_period 0 auto_recover true auto_dump true
+	  reporter hw_npa_err
+	      state healthy error 2871 recover 2871 last_dump_date 2020-12-10 last_dump_time 09:39:17 grace_period 0 auto_recover true auto_dump true
+	   reporter hw_npa_ras
+	      state healthy error 0 recover 0 last_dump_date 2020-12-10 last_dump_time 09:32:40 grace_period 0 auto_recover true auto_dump true
 
 Each reporter dumps the
+
  - Error Type
  - Error Register value
  - Reason in words
 
-For eg:
-~# devlink health dump show  pci/0002:01:00.0 reporter hw_npa_gen
- NPA_AF_GENERAL:
-         NPA General Interrupt Reg : 1
-         NIX0: free disabled RX
-~# devlink health dump show  pci/0002:01:00.0 reporter hw_npa_intr
- NPA_AF_RVU:
-         NPA RVU Interrupt Reg : 1
-         Unmap Slot Error
-~# devlink health dump show  pci/0002:01:00.0 reporter hw_npa_err
- NPA_AF_ERR:
-        NPA Error Interrupt Reg : 4096
-        AQ Doorbell Error
+For example::
+
+	~# devlink health dump show  pci/0002:01:00.0 reporter hw_npa_gen
+	 NPA_AF_GENERAL:
+	         NPA General Interrupt Reg : 1
+	         NIX0: free disabled RX
+	~# devlink health dump show  pci/0002:01:00.0 reporter hw_npa_intr
+	 NPA_AF_RVU:
+	         NPA RVU Interrupt Reg : 1
+	         Unmap Slot Error
+	~# devlink health dump show  pci/0002:01:00.0 reporter hw_npa_err
+	 NPA_AF_ERR:
+	        NPA Error Interrupt Reg : 4096
+	        AQ Doorbell Error

Documentation/networking/netdevices.rst

@@ -64,8 +64,8 @@ ndo_do_ioctl:
 	Context: process
 
 ndo_get_stats:
-	Synchronization: dev_base_lock rwlock.
-	Context: nominally process, but don't sleep inside an rwlock
+	Synchronization: rtnl_lock() semaphore, dev_base_lock rwlock, or RCU.
+	Context: atomic (can't sleep under rwlock or RCU)
 
 ndo_start_xmit:
 	Synchronization: __netif_tx_lock spinlock.

MAINTAINERS

@@ -10847,7 +10847,7 @@ F:	drivers/media/radio/radio-maxiradio*
 
 MCAN MMIO DEVICE DRIVER
 M:	Dan Murphy <[email protected]>
-M:	Sriram Dash <sriram.dash@samsung.com>
+M:	Pankaj Sharma <pankj.sharma@samsung.com>
 L:	[email protected]
 S:	Maintained
 F:	Documentation/devicetree/bindings/net/can/bosch,m_can.yaml

drivers/isdn/mISDN/Kconfig

@@ -13,6 +13,7 @@ if MISDN != n
 config MISDN_DSP
 	tristate "Digital Audio Processing of transparent data"
 	depends on MISDN
+	select BITREVERSE
 	help
 	  Enable support for digital audio processing capability.
 

drivers/net/bareudp.c

@@ -645,11 +645,20 @@ static int bareudp_link_config(struct net_device *dev,
 	return 0;
 }
 
+static void bareudp_dellink(struct net_device *dev, struct list_head *head)
+{
+	struct bareudp_dev *bareudp = netdev_priv(dev);
+
+	list_del(&bareudp->next);
+	unregister_netdevice_queue(dev, head);
+}
+
 static int bareudp_newlink(struct net *net, struct net_device *dev,
 			   struct nlattr *tb[], struct nlattr *data[],
 			   struct netlink_ext_ack *extack)
 {
 	struct bareudp_conf conf;
+	LIST_HEAD(list_kill);
 	int err;
 
 	err = bareudp2info(data, &conf, extack);
@@ -662,17 +671,14 @@ static int bareudp_newlink(struct net *net, struct net_device *dev,
 
 	err = bareudp_link_config(dev, tb);
 	if (err)
-		return err;
+		goto err_unconfig;
 
 	return 0;
-}
-
-static void bareudp_dellink(struct net_device *dev, struct list_head *head)
-{
-	struct bareudp_dev *bareudp = netdev_priv(dev);
 
-	list_del(&bareudp->next);
-	unregister_netdevice_queue(dev, head);
+err_unconfig:
+	bareudp_dellink(dev, &list_kill);
+	unregister_netdevice_many(&list_kill);
+	return err;
 }
 
 static size_t bareudp_get_size(const struct net_device *dev)

drivers/net/can/Kconfig

@@ -123,6 +123,7 @@ config CAN_JANZ_ICAN3
 config CAN_KVASER_PCIEFD
 	depends on PCI
 	tristate "Kvaser PCIe FD cards"
+	select CRC32
 	  help
 	  This is a driver for the Kvaser PCI Express CAN FD family.
 

drivers/net/can/m_can/m_can.c

@@ -1852,8 +1852,6 @@ EXPORT_SYMBOL_GPL(m_can_class_register);
 void m_can_class_unregister(struct m_can_classdev *cdev)
 {
 	unregister_candev(cdev->net);
-
-	m_can_clk_stop(cdev);
 }
 EXPORT_SYMBOL_GPL(m_can_class_unregister);
 

drivers/net/can/m_can/tcan4x5x.c

@@ -131,30 +131,6 @@ static inline struct tcan4x5x_priv *cdev_to_priv(struct m_can_classdev *cdev)
 
 }
 
-static struct can_bittiming_const tcan4x5x_bittiming_const = {
-	.name = DEVICE_NAME,
-	.tseg1_min = 2,
-	.tseg1_max = 31,
-	.tseg2_min = 2,
-	.tseg2_max = 16,
-	.sjw_max = 16,
-	.brp_min = 1,
-	.brp_max = 32,
-	.brp_inc = 1,
-};
-
-static struct can_bittiming_const tcan4x5x_data_bittiming_const = {
-	.name = DEVICE_NAME,
-	.tseg1_min = 1,
-	.tseg1_max = 32,
-	.tseg2_min = 1,
-	.tseg2_max = 16,
-	.sjw_max = 16,
-	.brp_min = 1,
-	.brp_max = 32,
-	.brp_inc = 1,
-};
-
 static void tcan4x5x_check_wake(struct tcan4x5x_priv *priv)
 {
 	int wake_state = 0;
@@ -469,8 +445,6 @@ static int tcan4x5x_can_probe(struct spi_device *spi)
 	mcan_class->dev = &spi->dev;
 	mcan_class->ops = &tcan4x5x_ops;
 	mcan_class->is_peripheral = true;
-	mcan_class->bit_timing = &tcan4x5x_bittiming_const;
-	mcan_class->data_timing = &tcan4x5x_data_bittiming_const;
 	mcan_class->net->irq = spi->irq;
 
 	spi_set_drvdata(spi, priv);

drivers/net/can/rcar/Kconfig

@@ -1,10 +1,10 @@
 # SPDX-License-Identifier: GPL-2.0
 config CAN_RCAR
-	tristate "Renesas R-Car CAN controller"
+	tristate "Renesas R-Car and RZ/G CAN controller"
 	depends on ARCH_RENESAS || ARM
 	help
 	  Say Y here if you want to use CAN controller found on Renesas R-Car
-	  SoCs.
+	  or RZ/G SoCs.
 
 	  To compile this driver as a module, choose M here: the module will
 	  be called rcar_can.

drivers/net/can/spi/mcp251xfd/mcp251xfd-core.c

@@ -1368,13 +1368,10 @@ static int mcp251xfd_handle_tefif(struct mcp251xfd_priv *priv)
 		struct mcp251xfd_tx_ring *tx_ring = priv->tx;
 		struct spi_transfer *last_xfer;
 
-		tx_ring->tail += len;
-
 		/* Increment the TEF FIFO tail pointer 'len' times in
 		 * a single SPI message.
-		 */
-
-		/* Note:
+		 *
+		 * Note:
 		 *
 		 * "cs_change == 1" on the last transfer results in an
 		 * active chip select after the complete SPI
@@ -1391,6 +1388,8 @@ static int mcp251xfd_handle_tefif(struct mcp251xfd_priv *priv)
 		if (err)
 			return err;
 
+		tx_ring->tail += len;
+
 		err = mcp251xfd_check_tef_tail(priv);
 		if (err)
 			return err;
@@ -1553,10 +1552,8 @@ mcp251xfd_handle_rxif_ring(struct mcp251xfd_priv *priv,
 
 		/* Increment the RX FIFO tail pointer 'len' times in a
 		 * single SPI message.
-		 */
-		ring->tail += len;
-
-		/* Note:
+		 *
+		 * Note:
 		 *
 		 * "cs_change == 1" on the last transfer results in an
 		 * active chip select after the complete SPI
@@ -1572,6 +1569,8 @@ mcp251xfd_handle_rxif_ring(struct mcp251xfd_priv *priv,
 		last_xfer->cs_change = 1;
 		if (err)
 			return err;
+
+		ring->tail += len;
 	}
 
 	return 0;

drivers/net/dsa/hirschmann/Kconfig

@@ -4,6 +4,7 @@ config NET_DSA_HIRSCHMANN_HELLCREEK
 	depends on HAS_IOMEM
 	depends on NET_DSA
 	depends on PTP_1588_CLOCK
+	depends on LEDS_CLASS
 	select NET_DSA_TAG_HELLCREEK
 	help
 	  This driver adds support for Hirschmann Hellcreek TSN switches.

drivers/net/dsa/lantiq_gswip.c

@@ -1436,11 +1436,12 @@ static void gswip_phylink_validate(struct dsa_switch *ds, int port,
 	phylink_set(mask, Pause);
 	phylink_set(mask, Asym_Pause);
 
-	/* With the exclusion of MII and Reverse MII, we support Gigabit,
-	 * including Half duplex
+	/* With the exclusion of MII, Reverse MII and Reduced MII, we
+	 * support Gigabit, including Half duplex
 	 */
 	if (state->interface != PHY_INTERFACE_MODE_MII &&
-	    state->interface != PHY_INTERFACE_MODE_REVMII) {
+	    state->interface != PHY_INTERFACE_MODE_REVMII &&
+	    state->interface != PHY_INTERFACE_MODE_RMII) {
 		phylink_set(mask, 1000baseT_Full);
 		phylink_set(mask, 1000baseT_Half);
 	}