Merge branch 'asoc-5.1' into asoc-next

Documentation/devicetree/bindings/sound/adi,adau1977.txt

@@ -23,6 +23,12 @@ Optional properties:
  - DVDD-supply: supply voltage for the digital core, please consult
                 Documentation/devicetree/bindings/regulator/regulator.txt
 
+- adi,micbias: configures the voltage setting for the MICBIAS pin.
+		Select 0/1/2/3/4/5/6/7/8 to specify MICBIAS voltage
+		5V/5.5V/6V/6.5V/7V/7.5V/8V/8.5V/9V
+		If not specified the default value will be "7" meaning 8.5 Volts.
+		This property is only valid for the ADAU1977
+
 For required properties on SPI, please consult
 Documentation/devicetree/bindings/spi/spi-bus.txt
 
@@ -40,6 +46,7 @@ Examples:
 		AVDD-supply = <&regulator>;
 		DVDD-supply = <&regulator_digital>;
 
+		adi,micbias = <3>;
 		reset-gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
 	};
 

Documentation/devicetree/bindings/sound/ak4458.txt

@@ -4,7 +4,7 @@ This device supports I2C mode.
 
 Required properties:
 
-- compatible : "asahi-kasei,ak4458"
+- compatible : "asahi-kasei,ak4458" or "asahi-kasei,ak4497"
 - reg : The I2C address of the device for I2C
 
 Optional properties:

Documentation/devicetree/bindings/sound/cs35l36.txt

@@ -0,0 +1,168 @@
+CS35L36 Speaker Amplifier
+
+Required properties:
+
+  - compatible : "cirrus,cs35l36"
+
+  - reg : the I2C address of the device for I2C
+
+  - VA-supply, VP-supply : power supplies for the device,
+  as covered in
+  Documentation/devicetree/bindings/regulator/regulator.txt.
+
+  - cirrus,boost-ctl-millivolt : Boost Voltage Value.  Configures the boost
+  converter's output voltage in mV. The range is from 2550mV to 12000mV with
+  increments of 50mV.
+  (Default) VP
+
+  - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
+  Configures the peak current by monitoring the current through the boost FET.
+  Range starts at 1600mA and goes to a maximum of 4500mA with increments of
+  50mA.
+  (Default) 4.50 Amps
+
+  - cirrus,boost-ind-nanohenry : Inductor estimation LBST reference value.
+  Seeds the digital boost converter's inductor estimation block with the initial
+  inductance value to reference.
+
+  1000 = 1uH (Default)
+  1200 = 1.2uH
+
+Optional properties:
+  - cirrus,multi-amp-mode : Boolean to determine if there are more than
+  one amplifier in the system. If more than one it is best to Hi-Z the ASP
+  port to prevent bus contention on the output signal
+
+  - cirrus,boost-ctl-select : Boost conerter control source selection.
+  Selects the source of the BST_CTL target VBST voltage for the boost
+  converter to generate.
+  0x00 - Control Port Value
+  0x01 - Class H Tracking (Default)
+  0x10 - MultiDevice Sync Value
+
+  - cirrus,amp-pcm-inv : Boolean to determine Amplifier will invert incoming
+  PCM data
+
+  - cirrus,imon-pol-inv : Boolean to determine Amplifier will invert the
+  polarity of outbound IMON feedback data
+
+  - cirrus,vmon-pol-inv : Boolean to determine Amplifier will invert the
+  polarity of outbound VMON feedback data
+
+  - cirrus,dcm-mode-enable : Boost converter automatic DCM Mode enable.
+  This enables the digital boost converter to operate in a low power
+  (Discontinuous Conduction) mode during low loading conditions.
+
+  - cirrus,weak-fet-disable : Boolean : The strength of the output drivers is
+  reduced when operating in a Weak-FET Drive Mode and must not be used to drive
+  a large load.
+
+  - cirrus,classh-wk-fet-delay :  Weak-FET entry delay. Controls the delay
+  (in ms) before the Class H algorithm switches to the weak-FET voltage
+  (after the audio falls and remains below the value specified in WKFET_AMP_THLD).
+
+  0 = 0ms
+  1 = 5ms
+  2 = 10ms
+  3 = 50ms
+  4 = 100ms (Default)
+  5 = 200ms
+  6 = 500ms
+  7 = 1000ms
+
+  - cirrus,classh-weak-fet-thld-millivolt : Weak-FET amplifier drive threshold.
+  Configures the signal threshold at which the PWM output stage enters
+  weak-FET operation. The range is 50mV to 700mV in 50mV increments.
+
+  - cirrus,temp-warn-threshold :  Amplifier overtemperature warning threshold.
+  Configures the threshold at which the overtemperature warning condition occurs.
+  When the threshold is met, the overtemperature warning attenuation is applied
+  and the TEMP_WARN_EINT interrupt status bit is set.
+  If TEMP_WARN_MASK = 0, INTb is asserted.
+
+  0 = 105C
+  1 = 115C
+  2 = 125C (Default)
+  3 = 135C
+
+  - cirrus,irq-drive-select : Selects the driver type of the selected interrupt
+  output.
+
+  0 = Open-drain
+  1 = Push-pull (Default)
+
+  - cirrus,irq-gpio-select : Selects the pin to serve as the programmable
+  interrupt output.
+
+  0 = PDM_DATA / SWIRE_SD / INT (Default)
+  1 = GPIO
+
+Optional properties for the "cirrus,vpbr-config" Sub-node
+
+  - cirrus,vpbr-en : VBST brownout prevention enable. Configures whether the
+  VBST brownout prevention algorithm is enabled or disabled.
+
+  0 = VBST brownout prevention disabled (default)
+  1 = VBST brownout prevention enabled
+
+  See Section 7.31.1 VPBR Config for configuration options & further details
+
+  - cirrus,vpbr-thld : Initial VPBR threshold. Configures the VP brownout
+  threshold voltage
+
+  - cirrus,cirrus,vpbr-atk-rate : Attenuation attack step rate. Configures the
+  amount delay between consecutive volume attenuation steps when a brownout
+  condition is present and the VP brownout condition is in an attacking state.
+
+  - cirrus,vpbr-atk-vol : VP brownout prevention step size. Configures the VP
+  brownout prevention attacking attenuation step size when operating in either
+  digital volume or analog gain modes.
+
+  - cirrus,vpbr-max-attn : Maximum attenuation that the VP brownout prevention
+  can apply to the audio signal.
+
+  - cirrus,vpbr-wait : Configures the delay time between a brownout condition
+  no longer being present and the VP brownout prevention entering an attenuation
+  release state.
+
+  - cirrus,vpbr-rel-rate : Attenuation release step rate. Configures the delay
+  between consecutive volume attenuation release steps when a brownout condition
+  is not longer present and the VP brownout is in an attenuation release state.
+
+  - cirrus,vpbr-mute-en : During the attack state, if the vpbr-max-attn value
+  is reached, the error condition still remains, and this bit is set, the audio
+  is muted.
+
+Example:
+
+cs35l36: cs35l36@40 {
+	compatible = "cirrus,cs35l36";
+	reg = <0x40>;
+	VA-supply = <&dummy_vreg>;
+	VP-supply = <&dummy_vreg>;
+	reset-gpios = <&gpio0 54 0>;
+	interrupt-parent = <&gpio8>;
+	interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+	cirrus,boost-ind-nanohenry = <1000>;
+	cirrus,boost-ctl-millivolt = <10000>;
+	cirrus,boost-peak-milliamp = <4500>;
+	cirrus,boost-ctl-select = <0x00>;
+	cirrus,weak-fet-delay = <0x04>;
+	cirrus,weak-fet-thld = <0x01>;
+	cirrus,temp-warn-threshold = <0x01>;
+	cirrus,multi-amp-mode;
+	cirrus,irq-drive-select = <0x01>;
+	cirrus,irq-gpio-select = <0x01>;
+
+	cirrus,vpbr-config {
+		cirrus,vpbr-en = <0x00>;
+		cirrus,vpbr-thld = <0x05>;
+		cirrus,vpbr-atk-rate = <0x02>;
+		cirrus,vpbr-atk-vol = <0x01>;
+		cirrus,vpbr-max-attn = <0x09>;
+		cirrus,vpbr-wait = <0x01>;
+		cirrus,vpbr-rel-rate = <0x05>;
+		cirrus,vpbr-mute-en = <0x00>;
+	};
+};

Documentation/devicetree/bindings/sound/cs4341.txt

@@ -0,0 +1,22 @@
+Cirrus Logic CS4341 audio DAC
+
+This device supports both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+  - compatible: "cirrus,cs4341a"
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+For required properties on I2C-bus, please consult
+Documentation/devicetree/bindings/i2c/i2c.txt
+For required properties on SPI-bus, please consult
+Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Example:
+	codec: cs4341@0 {
+		#sound-dai-cells = <0>;
+		compatible = "cirrus,cs4341a";
+		reg = <0>;
+		spi-max-frequency = <6000000>;
+	};

Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt

@@ -45,6 +45,23 @@ Optional properties:
 - fck_parent : Should contain a valid clock name which will be used as parent
 	       for the McASP fck
 
+Optional GPIO support:
+If any McASP pin need to be used as GPIO then the McASP node must have:
+...
+  gpio-controller
+  #gpio-cells = <2>;
+...
+
+When requesting a GPIO, the first parameter is the PIN index in McASP_P*
+registers.
+For example to request the AXR2 pin of mcasp8:
+function-gpios = <&mcasp8 2 0>;
+
+Or to request the ACLKR pin of mcasp8:
+function-gpios = <&mcasp8 29 0>;
+
+For generic gpio information, please refer to bindings/gpio/gpio.txt
+
 Example:
 
 mcasp0: mcasp0@1d00000 {