Merge tag 'for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git…

…/sre/linux-power-supply

Pull power supply and reset updates from Sebastian Reichel:
 - introduce reboot mode driver
 - add DT support to max8903
 - add power supply support for axp221
 - misc fixes

* tag 'for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
  power: reset: add reboot mode driver
  dt-bindings: power: reset: add document for reboot-mode driver
  power_supply: fix return value of get_property
  power: qcom_smbb: Make an extcon for usb cable detection
  max8903: adds support for initiation via device tree
  max8903: adds documentation for device tree bindings.
  max8903: remove unnecessary 'out of memory' error message.
  max8903: removes non zero validity checks on gpios.
  max8903: adds requesting of gpios.
  max8903: cleans up confusing relationship between dc_valid, dok and dcm.
  max8903: store pointer to pdata instead of copying it.
  power_supply: bq27xxx_battery: Group register mappings into one table
  docs: Move brcm,bcm21664-resetmgr.txt
  power/reset: make syscon_poweroff() static
  power: axp20x_usb: Add support for usb power-supply on axp22x pmics
  power_supply: bq27xxx_battery: Index register numbers by enum
  power_supply: bq27xxx_battery: Fix copy/paste error in header comment
  MAINTAINERS: Add file patterns for power supply device tree bindings
  power: reset: keystone: Enable COMPILE_TEST

Documentation/devicetree/bindings/power/max8903-charger.txt

@@ -0,0 +1,25 @@
+Maxim Semiconductor MAX8903 Battery Charger bindings
+
+Required properties:
+- compatible: "maxim,max8903" for MAX8903 Battery Charger
+- dok-gpios: Valid DC power has been detected (active low, input), optional if uok-gpios is provided
+- uok-gpios: Valid USB power has been detected (active low, input), optional if dok-gpios is provided
+
+Optional properties:
+- cen-gpios: Charge enable pin (active low, output)
+- chg-gpios: Charger status pin (active low, input)
+- flt-gpios: Fault pin (active low, output)
+- dcm-gpios: Current limit mode setting (DC=1 or USB=0, output)
+- usus-gpios: USB suspend pin (active high, output)
+
+
+Example:
+
+	max8903-charger {
+		compatible = "maxim,max8903";
+		dok-gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+		flt-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+		chg-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>;
+		cen-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
+		status = "okay";
+	};

Documentation/devicetree/bindings/power/reset/reboot-mode.txt

@@ -0,0 +1,25 @@
+Generic reboot mode core map driver
+
+This driver get reboot mode arguments and call the write
+interface to store the magic value in special register
+or ram. Then the bootloader can read it and take different
+action according to the argument stored.
+
+All mode properties are vendor specific, it is a indication to tell
+the bootloader what to do when the system reboots, and should be named
+as mode-xxx = <magic> (xxx is mode name, magic should be a none-zero value).
+
+For example modes common on Android platform:
+- mode-normal: Normal reboot mode, system reboot with command "reboot".
+- mode-recovery: Android Recovery mode, it is a mode to format the device or update a new image.
+- mode-bootloader: Android fastboot mode, it's a mode to re-flash partitions on the Android based device.
+- mode-loader: A bootloader mode, it's a mode used to download image on Rockchip platform,
+	       usually used in development.
+
+Example:
+	reboot-mode {
+		mode-normal = <BOOT_NORMAL>;
+		mode-recovery = <BOOT_RECOVERY>;
+		mode-bootloader = <BOOT_FASTBOOT>;
+		mode-loader = <BOOT_BL_DOWNLOAD>;
+	}

Documentation/devicetree/bindings/power/reset/syscon-reboot-mode.txt

@@ -0,0 +1,35 @@
+SYSCON reboot mode driver
+
+This driver gets reboot mode magic value form reboot-mode driver
+and stores it in a SYSCON mapped register. Then the bootloader
+can read it and take different action according to the magic
+value stored.
+
+This DT node should be represented as a sub-node of a "syscon", "simple-mfd"
+node.
+
+Required properties:
+- compatible: should be "syscon-reboot-mode"
+- offset: offset in the register map for the storage register (in bytes)
+
+Optional property:
+- mask: bits mask of the bits in the register to store the reboot mode magic value,
+  default set to 0xffffffff if missing.
+
+The rest of the properties should follow the generic reboot-mode description
+found in reboot-mode.txt
+
+Example:
+	pmu: pmu@20004000 {
+		compatible = "rockchip,rk3066-pmu", "syscon", "simple-mfd";
+		reg = <0x20004000 0x100>;
+
+		reboot-mode {
+			compatible = "syscon-reboot-mode";
+			offset = <0x40>;
+			mode-normal = <BOOT_NORMAL>;
+			mode-recovery = <BOOT_RECOVERY>;
+			mode-bootloader = <BOOT_FASTBOOT>;
+			mode-loader = <BOOT_BL_DOWNLOAD>;
+		};
+	};

Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt

@@ -1,7 +1,8 @@
 AXP20x USB power supply
 
 Required Properties:
--compatible: "x-powers,axp202-usb-power-supply"
+-compatible: One of: "x-powers,axp202-usb-power-supply"
+                     "x-powers,axp221-usb-power-supply"
 
 This node is a subnode of the axp20x PMIC.
 

MAINTAINERS

@@ -9169,6 +9169,8 @@ M:	David Woodhouse <[email protected]>
 L:	[email protected]
 T:	git git://git.infradead.org/battery-2.6.git
 S:	Maintained
+F:	Documentation/devicetree/bindings/power/
+F:	Documentation/devicetree/bindings/power_supply/
 F:	include/linux/power_supply.h
 F:	drivers/power/
 X:	drivers/power/avs/

drivers/power/Kconfig

@@ -394,6 +394,7 @@ config CHARGER_QCOM_SMBB
 	tristate "Qualcomm Switch-Mode Battery Charger and Boost"
 	depends on MFD_SPMI_PMIC || COMPILE_TEST
 	depends on OF
+	depends on EXTCON
 	help
 	  Say Y to include support for the Switch-Mode Battery Charger and
 	  Boost (SMBB) hardware found in Qualcomm PM8941 PMICs.  The charger

drivers/power/axp20x_usb_power.c

@@ -42,6 +42,7 @@
 #define AXP20X_VBUS_MON_VBUS_VALID	BIT(3)
 
 struct axp20x_usb_power {
+	struct device_node *np;
 	struct regmap *regmap;
 	struct power_supply *supply;
 };
@@ -85,7 +86,12 @@ static int axp20x_usb_power_get_property(struct power_supply *psy,
 
 		switch (v & AXP20X_VBUS_CLIMIT_MASK) {
 		case AXP20X_VBUC_CLIMIT_100mA:
-			val->intval = 100000;
+			if (of_device_is_compatible(power->np,
+					"x-powers,axp202-usb-power-supply")) {
+				val->intval = 100000;
+			} else {
+				val->intval = -1; /* No 100mA limit */
+			}
 			break;
 		case AXP20X_VBUC_CLIMIT_500mA:
 			val->intval = 500000;
@@ -122,16 +128,19 @@ static int axp20x_usb_power_get_property(struct power_supply *psy,
 			break;
 		}
 
-		ret = regmap_read(power->regmap, AXP20X_USB_OTG_STATUS, &v);
-		if (ret)
-			return ret;
+		val->intval = POWER_SUPPLY_HEALTH_GOOD;
 
-		if (!(v & AXP20X_USB_STATUS_VBUS_VALID)) {
-			val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
-			break;
-		}
+		if (of_device_is_compatible(power->np,
+				"x-powers,axp202-usb-power-supply")) {
+			ret = regmap_read(power->regmap,
+					  AXP20X_USB_OTG_STATUS, &v);
+			if (ret)
+				return ret;
 
-		val->intval = POWER_SUPPLY_HEALTH_GOOD;
+			if (!(v & AXP20X_USB_STATUS_VBUS_VALID))
+				val->intval =
+					POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
+		}
 		break;
 	case POWER_SUPPLY_PROP_PRESENT:
 		val->intval = !!(input & AXP20X_PWR_STATUS_VBUS_PRESENT);
@@ -156,6 +165,14 @@ static enum power_supply_property axp20x_usb_power_properties[] = {
 	POWER_SUPPLY_PROP_CURRENT_NOW,
 };
 
+static enum power_supply_property axp22x_usb_power_properties[] = {
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_ONLINE,
+	POWER_SUPPLY_PROP_VOLTAGE_MIN,
+	POWER_SUPPLY_PROP_CURRENT_MAX,
+};
+
 static const struct power_supply_desc axp20x_usb_power_desc = {
 	.name = "axp20x-usb",
 	.type = POWER_SUPPLY_TYPE_USB,
@@ -164,13 +181,25 @@ static const struct power_supply_desc axp20x_usb_power_desc = {
 	.get_property = axp20x_usb_power_get_property,
 };
 
+static const struct power_supply_desc axp22x_usb_power_desc = {
+	.name = "axp20x-usb",
+	.type = POWER_SUPPLY_TYPE_USB,
+	.properties = axp22x_usb_power_properties,
+	.num_properties = ARRAY_SIZE(axp22x_usb_power_properties),
+	.get_property = axp20x_usb_power_get_property,
+};
+
 static int axp20x_usb_power_probe(struct platform_device *pdev)
 {
 	struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
 	struct power_supply_config psy_cfg = {};
 	struct axp20x_usb_power *power;
-	static const char * const irq_names[] = { "VBUS_PLUGIN",
-		"VBUS_REMOVAL", "VBUS_VALID", "VBUS_NOT_VALID" };
+	static const char * const axp20x_irq_names[] = { "VBUS_PLUGIN",
+		"VBUS_REMOVAL", "VBUS_VALID", "VBUS_NOT_VALID", NULL };
+	static const char * const axp22x_irq_names[] = {
+		"VBUS_PLUGIN", "VBUS_REMOVAL", NULL };
+	static const char * const *irq_names;
+	const struct power_supply_desc *usb_power_desc;
 	int i, irq, ret;
 
 	if (!of_device_is_available(pdev->dev.of_node))
@@ -185,31 +214,47 @@ static int axp20x_usb_power_probe(struct platform_device *pdev)
 	if (!power)
 		return -ENOMEM;
 
+	power->np = pdev->dev.of_node;
 	power->regmap = axp20x->regmap;
 
-	/* Enable vbus valid checking */
-	ret = regmap_update_bits(power->regmap, AXP20X_VBUS_MON,
-		    AXP20X_VBUS_MON_VBUS_VALID, AXP20X_VBUS_MON_VBUS_VALID);
-	if (ret)
-		return ret;
+	if (of_device_is_compatible(power->np,
+			"x-powers,axp202-usb-power-supply")) {
+		/* Enable vbus valid checking */
+		ret = regmap_update_bits(power->regmap, AXP20X_VBUS_MON,
+					 AXP20X_VBUS_MON_VBUS_VALID,
+					 AXP20X_VBUS_MON_VBUS_VALID);
+		if (ret)
+			return ret;
 
-	/* Enable vbus voltage and current measurement */
-	ret = regmap_update_bits(power->regmap, AXP20X_ADC_EN1,
+		/* Enable vbus voltage and current measurement */
+		ret = regmap_update_bits(power->regmap, AXP20X_ADC_EN1,
 			AXP20X_ADC_EN1_VBUS_CURR | AXP20X_ADC_EN1_VBUS_VOLT,
 			AXP20X_ADC_EN1_VBUS_CURR | AXP20X_ADC_EN1_VBUS_VOLT);
-	if (ret)
-		return ret;
+		if (ret)
+			return ret;
+
+		usb_power_desc = &axp20x_usb_power_desc;
+		irq_names = axp20x_irq_names;
+	} else if (of_device_is_compatible(power->np,
+			"x-powers,axp221-usb-power-supply")) {
+		usb_power_desc = &axp22x_usb_power_desc;
+		irq_names = axp22x_irq_names;
+	} else {
+		dev_err(&pdev->dev, "Unsupported AXP variant: %ld\n",
+			axp20x->variant);
+		return -EINVAL;
+	}
 
 	psy_cfg.of_node = pdev->dev.of_node;
 	psy_cfg.drv_data = power;
 
-	power->supply = devm_power_supply_register(&pdev->dev,
-					&axp20x_usb_power_desc, &psy_cfg);
+	power->supply = devm_power_supply_register(&pdev->dev, usb_power_desc,
+						   &psy_cfg);
 	if (IS_ERR(power->supply))
 		return PTR_ERR(power->supply);
 
 	/* Request irqs after registering, as irqs may trigger immediately */
-	for (i = 0; i < ARRAY_SIZE(irq_names); i++) {
+	for (i = 0; irq_names[i]; i++) {
 		irq = platform_get_irq_byname(pdev, irq_names[i]);
 		if (irq < 0) {
 			dev_warn(&pdev->dev, "No IRQ for %s: %d\n",
@@ -229,6 +274,7 @@ static int axp20x_usb_power_probe(struct platform_device *pdev)
 
 static const struct of_device_id axp20x_usb_power_match[] = {
 	{ .compatible = "x-powers,axp202-usb-power-supply" },
+	{ .compatible = "x-powers,axp221-usb-power-supply" },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, axp20x_usb_power_match);