Updated slic3r default Overlord Pro Config Bundle

slic3r/default.ini

@@ -1,6 +1,185 @@
-# generated by Slic3r 1.2.8 on Tue Jun  9 21:25:13 2015
-avoid_crossing_perimeters = 1
+# generated by Slic3r 1.2.8 on Wed Jun 10 20:29:38 2015
+
+[filament:Overlord Pro]
+bed_temperature = 100
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 3
+extrusion_multiplier = 1
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.75
+first_layer_bed_temperature = 100
+first_layer_temperature = 220
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 10
+slowdown_below_layer_time = 5
+temperature = 210
+
+[filament:Simple Mode]
+bed_temperature = 70
+extrusion_multiplier = 1
+filament_diameter = 1.75
+first_layer_bed_temperature = 75
+first_layer_temperature = 235
+temperature = 230
+
+[presets]
+filament = Overlord Pro.ini
+print = Overlord Pro.ini
+printer = Overlord Pro.ini
+
+[print:Overlord Pro]
+avoid_crossing_perimeters = 0
+bottom_solid_layers = 4
+bridge_acceleration = 0
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_width = 0
+complete_objects = 0
+default_acceleration = 0
+dont_support_bridges = 1
+external_fill_pattern = concentric
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 50%
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_width = 0
+fill_angle = 45
+fill_density = 15%
+fill_pattern = honeycomb
+first_layer_acceleration = 0
+first_layer_extrusion_width = 200%
+first_layer_height = 0.35
+first_layer_speed = 20
+gap_fill_speed = 20
+gcode_comments = 0
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 15%
+infill_speed = 20
+interface_shells = 0
+layer_height = 0.2
+min_skirt_length = 0
+notes = 
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 0
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+perimeters = 2
+post_process = 
+raft_layers = 0
+resolution = 0
+seam_position = aligned
+skirt_distance = 6
+skirt_height = 1
+skirts = 1
+small_perimeter_speed = 20
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0
+solid_infill_speed = 20
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 1
+support_material_angle = 0
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = pillars
+support_material_spacing = 2.5
+support_material_speed = 20
+support_material_threshold = 0
+thin_walls = 1
+threads = 2
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 20
+top_solid_layers = 3
+travel_speed = 150
+xy_size_compensation = 0
+
+[print:Simple Mode]
+bottom_solid_layers = 3
+brim_width = 0
+dont_support_bridges = 1
+external_fill_pattern = concentric
+fill_density = 20%
+fill_pattern = honeycomb
+infill_speed = 80
+layer_height = 0.1
+perimeter_speed = 60
+perimeters = 3
+raft_layers = 0
+support_material = 0
+support_material_contact_distance = 0.2
+support_material_spacing = 2.5
+top_solid_layers = 3
+travel_speed = 150
+xy_size_compensation = 0
+
+[printer:Overlord Pro]
 bed_shape = 84.5344x8.88492,83.1425x17.6725,80.8398x26.2664,77.6514x34.5726,73.6122x42.5,68.7664x49.9617,63.1673x56.8761,56.8761x63.1673,49.9617x68.7664,42.5x73.6122,34.5726x77.6514,26.2664x80.8398,17.6725x83.1425,8.88492x84.5344,0x85,-8.88492x84.5344,-17.6725x83.1425,-26.2664x80.8398,-34.5726x77.6514,-42.5x73.6122,-49.9617x68.7664,-56.8761x63.1673,-63.1673x56.8761,-68.7664x49.9617,-73.6122x42.5,-77.6514x34.5726,-80.8398x26.2664,-83.1425x17.6725,-84.5344x8.88492,-85x0,-84.5344x-8.88492,-83.1425x-17.6725,-80.8398x-26.2664,-77.6514x-34.5726,-73.6122x-42.5,-68.7664x-49.9617,-63.1673x-56.8761,-56.8761x-63.1673,-49.9617x-68.7664,-42.5x-73.6122,-34.5726x-77.6514,-26.2664x-80.8398,-17.6725x-83.1425,-8.88492x-84.5344,0x-85,8.88492x-84.5344,17.6725x-83.1425,26.2664x-80.8398,34.5726x-77.6514,42.5x-73.6122,49.9617x-68.7664,56.8761x-63.1673,63.1673x-56.8761,68.7664x-49.9617,73.6122x-42.5,77.6514x-34.5726,80.8398x-26.2664,83.1425x-17.6725,84.5344x-8.88492,85x0
+before_layer_gcode = 
+end_gcode = 
+extruder_offset = 0x0
+gcode_flavor = reprap
+layer_gcode = 
+nozzle_diameter = 0.4
+octoprint_apikey = 
+octoprint_host = 
+pressure_advance = 0
+retract_before_travel = 1.5
+retract_layer_change = 0
+retract_length = 0.2
+retract_length_toolchange = 10
+retract_lift = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 40
+start_gcode = 
+toolchange_gcode = 
+use_firmware_retraction = 0
+use_relative_e_distances = 0
+use_volumetric_e = 0
+vibration_limit = 0
+wipe = 0
+z_offset = -0.3
+
+[printer:Simple Mode]
+bed_shape = 0x0,170x0,170x170,0x170
+end_gcode = ;End GCode\nM104 S0 ;extruder heater off\nM140 S0 ;heated bed heater off (if you have it)\nG91 ;relative positioning\nG1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more\nG28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way\nM84 ;steppers off\nG90 ;absolute positioning\n;{profile_string}
+gcode_flavor = reprap
+nozzle_diameter = 0.4
+retract_length = 2
+retract_lift = 0
+start_gcode = ;Sliced at: {day} {date} {time}\n;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}\n;Print time: {print_time}\n;Filament used: {filament_amount}m {filament_weight}g\n;Filament cost: {filament_cost}\n;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line\n;M109 S{print_temperature} ;Uncomment to add your own temperature line\nG21 ;metric values\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\nM107 ;start with the fan off\nG28 X0 Y0 ;move X/Y to min endstops\nG28 Z0 ;move Z to min endstops\nG1 Z15.0 F{travel_speed} ;move the platform down 15mm\nG92 E0 ;zero the extruded length\nG1 F200 E3 ;extrude 3mm of feed stock\nG92 E0 ;zero the extruded length again\nG1 F{travel_speed}\n;Put printing message on LCD screen\nM117 Printing...
+wipe = 0
+z_offset = 0
+
+[settings]
+autocenter = 1
+mode = expert
+
+[simple]
+avoid_crossing_perimeters = 1
+bed_shape = 0x0,170x0,170x170,0x170
 bed_temperature = 70
 before_layer_gcode = 
 bottom_solid_layers = 3
@@ -29,7 +208,6 @@ extrusion_multiplier = 1
 extrusion_width = 0
 fan_always_on = 0
 fan_below_layer_time = 60
-filament_colour = #FFFFFF
 filament_diameter = 1.75
 fill_angle = 45
 fill_density = 20%
@@ -56,8 +234,6 @@ interface_shells = 0
 layer_gcode = 
 layer_height = 0.3
 max_fan_speed = 100
-max_print_speed = 80
-max_volumetric_speed = 0
 min_fan_speed = 35
 min_print_speed = 10
 min_skirt_length = 0