doc/input : Fix typos in Documentation/input

This patch fix spelling typos in Documentations/input. Signed-off-by: Masanari Iida <[email protected]> Acked-by: Randy Dunlap <[email protected]> Signed-off-by: Jonathan Corbet <[email protected]>
jimmycarry · Mar 19, 2015 · ad4a6eb · ad4a6eb
1 parent 433b89c
commit ad4a6eb
Show file tree

Hide file tree

Showing 6 changed files with 7 additions and 7 deletions.
diff --git a/Documentation/input/alps.txt b/Documentation/input/alps.txt
@@ -58,7 +58,7 @@ To exit command mode, PSMOUSE_CMD_SETSTREAM (EA) is sent to the touchpad.
 While in command mode, register addresses can be set by first sending a
 specific command, either EC for v3 devices or F5 for v4 devices. Then the
 address is sent one nibble at a time, where each nibble is encoded as a
-command with optional data. This enoding differs slightly between the v3 and
+command with optional data. This encoding differs slightly between the v3 and
 v4 protocols.
 
 Once an address has been set, the addressed register can be read by sending
@@ -131,7 +131,7 @@ ALPS Absolute Mode - Protocol Version 3
 ---------------------------------------
 
 ALPS protocol version 3 has three different packet formats. The first two are
-associated with touchpad events, and the third is associatd with trackstick
+associated with touchpad events, and the third is associated with trackstick
 events.
 
 The first type is the touchpad position packet.

diff --git a/Documentation/input/event-codes.txt b/Documentation/input/event-codes.txt
@@ -229,7 +229,7 @@ such device to feedback.
 EV_PWR:
 ----------
 EV_PWR events are a special type of event used specifically for power
-mangement. Its usage is not well defined. To be addressed later.
+management. Its usage is not well defined. To be addressed later.
 
 Device properties:
 =================

diff --git a/Documentation/input/gpio-tilt.txt b/Documentation/input/gpio-tilt.txt
@@ -28,7 +28,7 @@ Example:
 --------
 
 Example configuration for a single TS1003 tilt switch that rotates around
-one axis in 4 steps and emitts the current tilt via two GPIOs.
+one axis in 4 steps and emits the current tilt via two GPIOs.
 
 static int sg060_tilt_enable(struct device *dev) {
 	/* code to enable the sensors */

diff --git a/Documentation/input/iforce-protocol.txt b/Documentation/input/iforce-protocol.txt
@@ -97,7 +97,7 @@ LEN= 0e
 *** Attack and fade ***
 OP=  02
 LEN= 08
-00-01 Address where to store the parameteres
+00-01 Address where to store the parameters
 02-03 Duration of attack (little endian encoding, in ms)
 04 Level at end of attack. Signed byte.
 05-06 Duration of fade.

diff --git a/Documentation/input/walkera0701.txt b/Documentation/input/walkera0701.txt
@@ -91,7 +91,7 @@ absolute binary value. (10 bits per channel). Next nibble is checksum for
 first ten nibbles.
 
 Next nibbles 12 .. 21 represents four channels (not all channels can be
-directly controlled from TX). Binary representations ar the same as in first
+directly controlled from TX). Binary representations are the same as in first
 four channels. In nibbles 22 and 23 is a special magic number. Nibble 24 is
 checksum for nibbles 12..23.
 

diff --git a/Documentation/input/yealink.txt b/Documentation/input/yealink.txt
@@ -93,7 +93,7 @@ Format description:
   Format specifier
     '8' :  Generic 7 segment digit with individual addressable segments
 
-    Reduced capability 7 segm digit, when segments are hard wired together.
+    Reduced capability 7 segment digit, when segments are hard wired together.
     '1' : 2 segments digit only able to produce a 1.
     'e' : Most significant day of the month digit,
           able to produce at least 1 2 3.