PCI/PM: Rename pci_dev.d3_delay to d3hot_delay

PCI devices support two variants of the D3 power state: D3hot (main power present) D3cold (main power removed). Previously struct pci_dev contained: unsigned int d3_delay; /* D3->D0 transition time in ms */ unsigned int d3cold_delay; /* D3cold->D0 transition time in ms */ "d3_delay" refers specifically to the D3hot state. Rename it to "d3hot_delay" to avoid ambiguity and align with the ACPI "_DSM for Specifying Device Readiness Durations" in the PCI Firmware spec r3.2, sec 4.6.9. There is no change to the functionality. Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Krzysztof Wilczyński <[email protected]> Signed-off-by: Bjorn Helgaas <[email protected]>
jix · Sep 29, 2020 · 3789af9 · 3789af9
1 parent a5d02e9
commit 3789af9
Show file tree

Hide file tree

Showing 12 changed files with 54 additions and 54 deletions.
diff --git a/Documentation/power/pci.rst b/Documentation/power/pci.rst
@@ -320,7 +320,7 @@ that these callbacks operate on::
 	unsigned int	d2_support:1;	/* Low power state D2 is supported */
 	unsigned int	no_d1d2:1;	/* D1 and D2 are forbidden */
 	unsigned int	wakeup_prepared:1;  /* Device prepared for wake up */
-	unsigned int	d3_delay;	/* D3->D0 transition time in ms */
+	unsigned int	d3hot_delay;	/* D3hot->D0 transition time in ms */
 	...
   };
 

diff --git a/arch/x86/pci/fixup.c b/arch/x86/pci/fixup.c
@@ -587,7 +587,7 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0xa26d, pci_invalid_bar);
 static void pci_fixup_amd_ehci_pme(struct pci_dev *dev)
 {
 	dev_info(&dev->dev, "PME# does not work under D3, disabling it\n");
-	dev->pme_support &= ~((PCI_PM_CAP_PME_D3 | PCI_PM_CAP_PME_D3cold)
+	dev->pme_support &= ~((PCI_PM_CAP_PME_D3hot | PCI_PM_CAP_PME_D3cold)
 		>> PCI_PM_CAP_PME_SHIFT);
 }
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x7808, pci_fixup_amd_ehci_pme);

diff --git a/arch/x86/pci/intel_mid_pci.c b/arch/x86/pci/intel_mid_pci.c
@@ -322,7 +322,7 @@ static void pci_d3delay_fixup(struct pci_dev *dev)
 	 */
 	if (type1_access_ok(dev->bus->number, dev->devfn, PCI_DEVICE_ID))
 		return;
-	dev->d3_delay = 0;
+	dev->d3hot_delay = 0;
 }
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_d3delay_fixup);
 

diff --git a/drivers/hid/intel-ish-hid/ipc/ipc.c b/drivers/hid/intel-ish-hid/ipc/ipc.c
@@ -755,7 +755,7 @@ static int _ish_hw_reset(struct ishtp_device *dev)
 	csr |= PCI_D3hot;
 	pci_write_config_word(pdev, pdev->pm_cap + PCI_PM_CTRL, csr);
 
-	mdelay(pdev->d3_delay);
+	mdelay(pdev->d3hot_delay);
 
 	csr &= ~PCI_PM_CTRL_STATE_MASK;
 	csr |= PCI_D0;

diff --git a/drivers/net/ethernet/marvell/sky2.c b/drivers/net/ethernet/marvell/sky2.c
@@ -5105,7 +5105,7 @@ static int sky2_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	INIT_WORK(&hw->restart_work, sky2_restart);
 
 	pci_set_drvdata(pdev, hw);
-	pdev->d3_delay = 300;
+	pdev->d3hot_delay = 300;
 
 	return 0;
 

diff --git a/drivers/pci/pci-acpi.c b/drivers/pci/pci-acpi.c
@@ -1167,7 +1167,7 @@ static struct acpi_device *acpi_pci_find_companion(struct device *dev)
  * @pdev: the PCI device whose delay is to be updated
  * @handle: ACPI handle of this device
  *
- * Update the d3_delay and d3cold_delay of a PCI device from the ACPI _DSM
+ * Update the d3hot_delay and d3cold_delay of a PCI device from the ACPI _DSM
  * control method of either the device itself or the PCI host bridge.
  *
  * Function 8, "Reset Delay," applies to the entire hierarchy below a PCI
@@ -1206,8 +1206,8 @@ static void pci_acpi_optimize_delay(struct pci_dev *pdev,
 		}
 		if (elements[3].type == ACPI_TYPE_INTEGER) {
 			value = (int)elements[3].integer.value / 1000;
-			if (value < PCI_PM_D3_WAIT)
-				pdev->d3_delay = value;
+			if (value < PCI_PM_D3HOT_WAIT)
+				pdev->d3hot_delay = value;
 		}
 	}
 	ACPI_FREE(obj);

diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
@@ -49,7 +49,7 @@ EXPORT_SYMBOL(isa_dma_bridge_buggy);
 int pci_pci_problems;
 EXPORT_SYMBOL(pci_pci_problems);
 
-unsigned int pci_pm_d3_delay;
+unsigned int pci_pm_d3hot_delay;
 
 static void pci_pme_list_scan(struct work_struct *work);
 
@@ -66,10 +66,10 @@ struct pci_pme_device {
 
 static void pci_dev_d3_sleep(struct pci_dev *dev)
 {
-	unsigned int delay = dev->d3_delay;
+	unsigned int delay = dev->d3hot_delay;
 
-	if (delay < pci_pm_d3_delay)
-		delay = pci_pm_d3_delay;
+	if (delay < pci_pm_d3hot_delay)
+		delay = pci_pm_d3hot_delay;
 
 	if (delay)
 		msleep(delay);
@@ -3013,7 +3013,7 @@ void pci_pm_init(struct pci_dev *dev)
 	}
 
 	dev->pm_cap = pm;
-	dev->d3_delay = PCI_PM_D3_WAIT;
+	dev->d3hot_delay = PCI_PM_D3HOT_WAIT;
 	dev->d3cold_delay = PCI_PM_D3COLD_WAIT;
 	dev->bridge_d3 = pci_bridge_d3_possible(dev);
 	dev->d3cold_allowed = true;
@@ -3038,7 +3038,7 @@ void pci_pm_init(struct pci_dev *dev)
 			 (pmc & PCI_PM_CAP_PME_D0) ? " D0" : "",
 			 (pmc & PCI_PM_CAP_PME_D1) ? " D1" : "",
 			 (pmc & PCI_PM_CAP_PME_D2) ? " D2" : "",
-			 (pmc & PCI_PM_CAP_PME_D3) ? " D3hot" : "",
+			 (pmc & PCI_PM_CAP_PME_D3hot) ? " D3hot" : "",
 			 (pmc & PCI_PM_CAP_PME_D3cold) ? " D3cold" : "");
 		dev->pme_support = pmc >> PCI_PM_CAP_PME_SHIFT;
 		dev->pme_poll = true;
@@ -4621,7 +4621,7 @@ static int pci_af_flr(struct pci_dev *dev, int probe)
  *
  * NOTE: This causes the caller to sleep for twice the device power transition
  * cooldown period, which for the D0->D3hot and D3hot->D0 transitions is 10 ms
- * by default (i.e. unless the @dev's d3_delay field has a different value).
+ * by default (i.e. unless the @dev's d3hot_delay field has a different value).
  * Moreover, only devices in D0 can be reset by this function.
  */
 static int pci_pm_reset(struct pci_dev *dev, int probe)

diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
@@ -44,7 +44,7 @@ int pci_bridge_secondary_bus_reset(struct pci_dev *dev);
 int pci_bus_error_reset(struct pci_dev *dev);
 
 #define PCI_PM_D2_DELAY         200
-#define PCI_PM_D3_WAIT          10
+#define PCI_PM_D3HOT_WAIT       10
 #define PCI_PM_D3COLD_WAIT      100
 #define PCI_PM_BUS_WAIT         50
 
@@ -178,7 +178,7 @@ extern struct mutex pci_slot_mutex;
 
 extern raw_spinlock_t pci_lock;
 
-extern unsigned int pci_pm_d3_delay;
+extern unsigned int pci_pm_d3hot_delay;
 
 #ifdef CONFIG_PCI_MSI
 void pci_no_msi(void);

diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
@@ -1846,7 +1846,7 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_PXHV,	quirk_pci
  */
 static void quirk_intel_pcie_pm(struct pci_dev *dev)
 {
-	pci_pm_d3_delay = 120;
+	pci_pm_d3hot_delay = 120;
 	dev->no_d1d2 = 1;
 }
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL,	0x25e2, quirk_intel_pcie_pm);
@@ -1873,12 +1873,12 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL,	0x260b, quirk_intel_pcie_pm);
 
 static void quirk_d3hot_delay(struct pci_dev *dev, unsigned int delay)
 {
-	if (dev->d3_delay >= delay)
+	if (dev->d3hot_delay >= delay)
 		return;
 
-	dev->d3_delay = delay;
+	dev->d3hot_delay = delay;
 	pci_info(dev, "extending delay after power-on from D3hot to %d msec\n",
-		 dev->d3_delay);
+		 dev->d3hot_delay);
 }
 
 static void quirk_radeon_pm(struct pci_dev *dev)
@@ -3387,36 +3387,36 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0152, disable_igfx_irq);
  * PCI devices which are on Intel chips can skip the 10ms delay
  * before entering D3 mode.
  */
-static void quirk_remove_d3_delay(struct pci_dev *dev)
-{
-	dev->d3_delay = 0;
-}
-/* C600 Series devices do not need 10ms d3_delay */
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0412, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0c00, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0c0c, quirk_remove_d3_delay);
-/* Lynxpoint-H PCH devices do not need 10ms d3_delay */
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c02, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c18, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c1c, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c20, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c22, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c26, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c2d, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c31, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c3a, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c3d, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c4e, quirk_remove_d3_delay);
-/* Intel Cherrytrail devices do not need 10ms d3_delay */
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2280, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2298, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x229c, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b0, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b5, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b7, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b8, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22d8, quirk_remove_d3_delay);
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22dc, quirk_remove_d3_delay);
+static void quirk_remove_d3hot_delay(struct pci_dev *dev)
+{
+	dev->d3hot_delay = 0;
+}
+/* C600 Series devices do not need 10ms d3hot_delay */
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0412, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0c00, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0c0c, quirk_remove_d3hot_delay);
+/* Lynxpoint-H PCH devices do not need 10ms d3hot_delay */
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c02, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c18, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c1c, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c20, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c22, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c26, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c2d, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c31, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c3a, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c3d, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c4e, quirk_remove_d3hot_delay);
+/* Intel Cherrytrail devices do not need 10ms d3hot_delay */
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2280, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2298, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x229c, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b0, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b5, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b7, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b8, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22d8, quirk_remove_d3hot_delay);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22dc, quirk_remove_d3hot_delay);
 
 /*
  * Some devices may pass our check in pci_intx_mask_supported() if

diff --git a/drivers/staging/media/atomisp/pci/atomisp_v4l2.c b/drivers/staging/media/atomisp/pci/atomisp_v4l2.c
@@ -1573,7 +1573,7 @@ static int atomisp_pci_probe(struct pci_dev *pdev, const struct pci_device_id *i
 	spin_lock_init(&isp->lock);
 
 	/* This is not a true PCI device on SoC, so the delay is not needed. */
-	pdev->d3_delay = 0;
+	pdev->d3hot_delay = 0;
 
 	pci_set_drvdata(pdev, isp);
 

diff --git a/include/linux/pci.h b/include/linux/pci.h
@@ -373,7 +373,7 @@ struct pci_dev {
 						      user sysfs */
 	unsigned int	clear_retrain_link:1;	/* Need to clear Retrain Link
 						   bit manually */
-	unsigned int	d3_delay;	/* D3->D0 transition time in ms */
+	unsigned int	d3hot_delay;	/* D3hot->D0 transition time in ms */
 	unsigned int	d3cold_delay;	/* D3cold->D0 transition time in ms */
 
 #ifdef CONFIG_PCIEASPM

diff --git a/include/uapi/linux/pci_regs.h b/include/uapi/linux/pci_regs.h
@@ -246,7 +246,7 @@
 #define  PCI_PM_CAP_PME_D0	0x0800	/* PME# from D0 */
 #define  PCI_PM_CAP_PME_D1	0x1000	/* PME# from D1 */
 #define  PCI_PM_CAP_PME_D2	0x2000	/* PME# from D2 */
-#define  PCI_PM_CAP_PME_D3	0x4000	/* PME# from D3 (hot) */
+#define  PCI_PM_CAP_PME_D3hot	0x4000	/* PME# from D3 (hot) */
 #define  PCI_PM_CAP_PME_D3cold	0x8000	/* PME# from D3 (cold) */
 #define  PCI_PM_CAP_PME_SHIFT	11	/* Start of the PME Mask in PMC */
 #define PCI_PM_CTRL		4	/* PM control and status register */