Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/ker…

…nel/git/jgarzik/netdev-2.6

Documentation/networking/gianfar.txt

@@ -0,0 +1,72 @@
+The Gianfar Ethernet Driver
+Sysfs File description
+
+Author: Andy Fleming <[email protected]>
+Updated: 2005-07-28
+
+SYSFS
+
+Several of the features of the gianfar driver are controlled
+through sysfs files.  These are:
+
+bd_stash:
+To stash RX Buffer Descriptors in the L2, echo 'on' or '1' to
+bd_stash, echo 'off' or '0' to disable
+
+rx_stash_len:
+To stash the first n bytes of the packet in L2, echo the number
+of bytes to buf_stash_len.  echo 0 to disable.
+
+WARNING: You could really screw these up if you set them too low or high!
+fifo_threshold:
+To change the number of bytes the controller needs in the
+fifo before it starts transmission, echo the number of bytes to 
+fifo_thresh.  Range should be 0-511.
+
+fifo_starve:
+When the FIFO has less than this many bytes during a transmit, it
+enters starve mode, and increases the priority of TX memory
+transactions.  To change, echo the number of bytes to
+fifo_starve.  Range should be 0-511.
+
+fifo_starve_off:
+Once in starve mode, the FIFO remains there until it has this
+many bytes.  To change, echo the number of bytes to
+fifo_starve_off.  Range should be 0-511.
+
+CHECKSUM OFFLOADING
+
+The eTSEC controller (first included in parts from late 2005 like
+the 8548) has the ability to perform TCP, UDP, and IP checksums
+in hardware.  The Linux kernel only offloads the TCP and UDP
+checksums (and always performs the pseudo header checksums), so
+the driver only supports checksumming for TCP/IP and UDP/IP
+packets.  Use ethtool to enable or disable this feature for RX
+and TX.
+
+VLAN
+
+In order to use VLAN, please consult Linux documentation on
+configuring VLANs.  The gianfar driver supports hardware insertion and
+extraction of VLAN headers, but not filtering.  Filtering will be
+done by the kernel.
+
+MULTICASTING
+
+The gianfar driver supports using the group hash table on the
+TSEC (and the extended hash table on the eTSEC) for multicast
+filtering.  On the eTSEC, the exact-match MAC registers are used
+before the hash tables.  See Linux documentation on how to join
+multicast groups.
+
+PADDING
+
+The gianfar driver supports padding received frames with 2 bytes
+to align the IP header to a 16-byte boundary, when supported by
+hardware.
+
+ETHTOOL
+
+The gianfar driver supports the use of ethtool for many
+configuration options.  You must run ethtool only on currently
+open interfaces.  See ethtool documentation for details.

drivers/net/8139too.c

@@ -586,16 +586,16 @@ struct rtl8139_private {
 	dma_addr_t tx_bufs_dma;
 	signed char phys[4];		/* MII device addresses. */
 	char twistie, twist_row, twist_col;	/* Twister tune state. */
-	unsigned int default_port:4;	/* Last dev->if_port value. */
+	unsigned int default_port : 4;	/* Last dev->if_port value. */
+	unsigned int have_thread : 1;
 	spinlock_t lock;
 	spinlock_t rx_lock;
 	chip_t chipset;
-	pid_t thr_pid;
-	wait_queue_head_t thr_wait;
-	struct completion thr_exited;
 	u32 rx_config;
 	struct rtl_extra_stats xstats;
-	int time_to_die;
+
+	struct work_struct thread;
+
 	struct mii_if_info mii;
 	unsigned int regs_len;
 	unsigned long fifo_copy_timeout;
@@ -620,7 +620,7 @@ static int rtl8139_open (struct net_device *dev);
 static int mdio_read (struct net_device *dev, int phy_id, int location);
 static void mdio_write (struct net_device *dev, int phy_id, int location,
 			int val);
-static void rtl8139_start_thread(struct net_device *dev);
+static void rtl8139_start_thread(struct rtl8139_private *tp);
 static void rtl8139_tx_timeout (struct net_device *dev);
 static void rtl8139_init_ring (struct net_device *dev);
 static int rtl8139_start_xmit (struct sk_buff *skb,
@@ -637,6 +637,7 @@ static struct net_device_stats *rtl8139_get_stats (struct net_device *dev);
 static void rtl8139_set_rx_mode (struct net_device *dev);
 static void __set_rx_mode (struct net_device *dev);
 static void rtl8139_hw_start (struct net_device *dev);
+static void rtl8139_thread (void *_data);
 static struct ethtool_ops rtl8139_ethtool_ops;
 
 /* write MMIO register, with flush */
@@ -1007,8 +1008,7 @@ static int __devinit rtl8139_init_one (struct pci_dev *pdev,
 		(debug < 0 ? RTL8139_DEF_MSG_ENABLE : ((1 << debug) - 1));
 	spin_lock_init (&tp->lock);
 	spin_lock_init (&tp->rx_lock);
-	init_waitqueue_head (&tp->thr_wait);
-	init_completion (&tp->thr_exited);
+	INIT_WORK(&tp->thread, rtl8139_thread, dev);
 	tp->mii.dev = dev;
 	tp->mii.mdio_read = mdio_read;
 	tp->mii.mdio_write = mdio_write;
@@ -1345,7 +1345,7 @@ static int rtl8139_open (struct net_device *dev)
 			dev->irq, RTL_R8 (MediaStatus),
 			tp->mii.full_duplex ? "full" : "half");
 
-	rtl8139_start_thread(dev);
+	rtl8139_start_thread(tp);
 
 	return 0;
 }
@@ -1594,55 +1594,43 @@ static inline void rtl8139_thread_iter (struct net_device *dev,
 		 RTL_R8 (Config1));
 }
 
-static int rtl8139_thread (void *data)
+static void rtl8139_thread (void *_data)
 {
-	struct net_device *dev = data;
+	struct net_device *dev = _data;
 	struct rtl8139_private *tp = netdev_priv(dev);
-	unsigned long timeout;
-
-	daemonize("%s", dev->name);
-	allow_signal(SIGTERM);
-
-	while (1) {
-		timeout = next_tick;
-		do {
-			timeout = interruptible_sleep_on_timeout (&tp->thr_wait, timeout);
-			/* make swsusp happy with our thread */
-			try_to_freeze();
-		} while (!signal_pending (current) && (timeout > 0));
-
-		if (signal_pending (current)) {
-			flush_signals(current);
-		}
+	unsigned long thr_delay;
 
-		if (tp->time_to_die)
-			break;
-
-		if (rtnl_lock_interruptible ())
-			break;
+	if (rtnl_shlock_nowait() == 0) {
 		rtl8139_thread_iter (dev, tp, tp->mmio_addr);
 		rtnl_unlock ();
+
+		thr_delay = next_tick;
+	} else {
+		/* unlikely race.  mitigate with fast poll. */
+		thr_delay = HZ / 2;
 	}
 
-	complete_and_exit (&tp->thr_exited, 0);
+	schedule_delayed_work(&tp->thread, thr_delay);
 }
 
-static void rtl8139_start_thread(struct net_device *dev)
+static void rtl8139_start_thread(struct rtl8139_private *tp)
 {
-	struct rtl8139_private *tp = netdev_priv(dev);
-
-	tp->thr_pid = -1;
 	tp->twistie = 0;
-	tp->time_to_die = 0;
 	if (tp->chipset == CH_8139_K)
 		tp->twistie = 1;
 	else if (tp->drv_flags & HAS_LNK_CHNG)
 		return;
 
-	tp->thr_pid = kernel_thread(rtl8139_thread, dev, CLONE_FS|CLONE_FILES);
-	if (tp->thr_pid < 0) {
-		printk (KERN_WARNING "%s: unable to start kernel thread\n",
-			dev->name);
+	tp->have_thread = 1;
+
+	schedule_delayed_work(&tp->thread, next_tick);
+}
+
+static void rtl8139_stop_thread(struct rtl8139_private *tp)
+{
+	if (tp->have_thread) {
+		cancel_rearming_delayed_work(&tp->thread);
+		tp->have_thread = 0;
 	}
 }
 
@@ -2224,22 +2212,12 @@ static int rtl8139_close (struct net_device *dev)
 {
 	struct rtl8139_private *tp = netdev_priv(dev);
 	void __iomem *ioaddr = tp->mmio_addr;
-	int ret = 0;
 	unsigned long flags;
 
 	netif_stop_queue (dev);
 
-	if (tp->thr_pid >= 0) {
-		tp->time_to_die = 1;
-		wmb();
-		ret = kill_proc (tp->thr_pid, SIGTERM, 1);
-		if (ret) {
-			printk (KERN_ERR "%s: unable to signal thread\n", dev->name);
-			return ret;
-		}
-		wait_for_completion (&tp->thr_exited);
-	}
-
+	rtl8139_stop_thread(tp);
+
 	if (netif_msg_ifdown(tp))
 		printk(KERN_DEBUG "%s: Shutting down ethercard, status was 0x%4.4x.\n",
 			dev->name, RTL_R16 (IntrStatus));

drivers/net/Kconfig

@@ -1901,6 +1901,8 @@ config E1000_NAPI
 
 	  If in doubt, say N.
 
+source "drivers/net/ixp2000/Kconfig"
+
 config MYRI_SBUS
 	tristate "MyriCOM Gigabit Ethernet support"
 	depends on SBUS
@@ -2008,7 +2010,18 @@ config SKGE
 
 	  It does not support the link failover and network management 
 	  features that "portable" vendor supplied sk98lin driver does.
-
+
+
+config SKY2
+	tristate "SysKonnect Yukon2 support (EXPERIMENTAL)"
+	depends on PCI && EXPERIMENTAL
+	select CRC32
+	---help---
+	  This driver support the Marvell Yukon 2 Gigabit Ethernet adapter.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called sky2.  This is recommended.
+
 config SK98LIN
 	tristate "Marvell Yukon Chipset / SysKonnect SK-98xx Support"
 	depends on PCI
@@ -2120,7 +2133,7 @@ config BNX2
 
 config SPIDER_NET
 	tristate "Spider Gigabit Ethernet driver"
-	depends on PCI && PPC_BPA
+	depends on PCI && PPC_CELL
 	help
 	  This driver supports the Gigabit Ethernet chips present on the
 	  Cell Processor-Based Blades from IBM.

drivers/net/Makefile

@@ -13,7 +13,10 @@ obj-$(CONFIG_CHELSIO_T1) += chelsio/
 obj-$(CONFIG_BONDING) += bonding/
 obj-$(CONFIG_GIANFAR) += gianfar_driver.o
 
-gianfar_driver-objs := gianfar.o gianfar_ethtool.o gianfar_mii.o
+gianfar_driver-objs := gianfar.o \
+		gianfar_ethtool.o \
+		gianfar_mii.o \
+		gianfar_sysfs.o
 
 #
 # link order important here
@@ -59,6 +62,7 @@ spidernet-y += spider_net.o spider_net_ethtool.o sungem_phy.o
 obj-$(CONFIG_SPIDER_NET) += spidernet.o
 obj-$(CONFIG_TC35815) += tc35815.o
 obj-$(CONFIG_SKGE) += skge.o
+obj-$(CONFIG_SKY2) += sky2.o
 obj-$(CONFIG_SK98LIN) += sk98lin/
 obj-$(CONFIG_SKFP) += skfp/
 obj-$(CONFIG_VIA_RHINE) += via-rhine.o
@@ -202,6 +206,7 @@ obj-$(CONFIG_NET_TULIP) += tulip/
 obj-$(CONFIG_HAMRADIO) += hamradio/
 obj-$(CONFIG_IRDA) += irda/
 obj-$(CONFIG_ETRAX_ETHERNET) += cris/
+obj-$(CONFIG_ENP2611_MSF_NET) += ixp2000/
 
 obj-$(CONFIG_NETCONSOLE) += netconsole.o
 

drivers/net/bonding/Makefile

@@ -4,5 +4,5 @@
 
 obj-$(CONFIG_BONDING) += bonding.o
 
-bonding-objs := bond_main.o bond_3ad.o bond_alb.o
+bonding-objs := bond_main.o bond_3ad.o bond_alb.o bond_sysfs.o