Merge tag 'usb-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel…

…/git/balbi/usb into usb-next

Felipe writes:

usb: patches for v4.2 merge window

- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs

Signed-off-by: Felipe Balbi <[email protected]>

Documentation/devicetree/bindings/power/twl-charger.txt

@@ -1,5 +1,15 @@
 TWL BCI (Battery Charger Interface)
 
+The battery charger needs to interact with the USB phy in order
+to know when charging is permissible, and when there is a connection
+or disconnection.
+
+The choice of phy cannot be configured at a hardware level, so there
+is no value in explicit configuration in device-tree.  Rather
+if there is a sibling of the BCI node which is compatible with
+"ti,twl4030-usb", then that is used to determine when and how
+use USB power for charging.
+
 Required properties:
 - compatible:
   - "ti,twl4030-bci"

Documentation/devicetree/bindings/usb/dwc3-st.txt

@@ -49,8 +49,7 @@ st_dwc3: dwc3@8f94000 {
 	st,syscfg	= <&syscfg_core>;
 	resets		= <&powerdown STIH407_USB3_POWERDOWN>,
 			  <&softreset STIH407_MIPHY2_SOFTRESET>;
-	reset-names	= "powerdown",
-			  "softreset";
+	reset-names	= "powerdown", "softreset";
 	#address-cells	= <1>;
 	#size-cells	= <1>;
 	pinctrl-names	= "default";
@@ -62,7 +61,7 @@ st_dwc3: dwc3@8f94000 {
 		reg		= <0x09900000 0x100000>;
 		interrupts	= <GIC_SPI 155 IRQ_TYPE_NONE>;
 		dr_mode		= "host";
-		phys-names      = "usb2-phy", "usb3-phy";
-		phys            = <&usb2_picophy2>, <&phy_port2 MIPHY_TYPE_USB>;
+		phy-names	= "usb2-phy", "usb3-phy";
+		phys		= <&usb2_picophy2>, <&phy_port2 PHY_TYPE_USB3>;
 	};
 };

Documentation/devicetree/bindings/usb/dwc3.txt

@@ -38,6 +38,8 @@ Optional properties:
  - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal
 			utmi_l1_suspend_n, false when asserts utmi_sleep_n
  - snps,hird-threshold: HIRD threshold
+ - snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for
+   UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3.
 
 This is usually a subnode to DWC3 glue to which it is connected.
 

Documentation/devicetree/bindings/usb/msm-hsusb.txt

@@ -69,6 +69,17 @@ Optional properties:
                 (no, min, max) where each value represents either a voltage
                 in microvolts or a value corresponding to voltage corner.
 
+- qcom,manual-pullup: If present, vbus is not routed to USB controller/phy
+                and controller driver therefore enables pull-up explicitly
+                before starting controller using usbcmd run/stop bit.
+
+- extcon:       phandles to external connector devices. First phandle
+                should point to external connector, which provide "USB"
+                cable events, the second should point to external connector
+                device, which provide "USB-HOST" cable events. If one of
+                the external connector devices is not required empty <0>
+                phandle should be specified.
+
 Example HSUSB OTG controller device node:
 
     usb@f9a55000 {

Documentation/devicetree/bindings/usb/renesas_usbhs.txt

@@ -4,6 +4,7 @@ Required properties:
   - compatible: Must contain one of the following:
 	- "renesas,usbhs-r8a7790"
 	- "renesas,usbhs-r8a7791"
+	- "renesas,usbhs-r8a7794"
   - reg: Base address and length of the register for the USBHS
   - interrupts: Interrupt specifier for the USBHS
   - clocks: A list of phandle + clock specifier pairs
@@ -15,10 +16,8 @@ Optional properties:
   - phys: phandle + phy specifier pair
   - phy-names: must be "usb"
   - dmas: Must contain a list of references to DMA specifiers.
-  - dma-names : Must contain a list of DMA names:
-   - tx0 ... tx<n>
-   - rx0 ... rx<n>
-    - This <n> means DnFIFO in USBHS module.
+  - dma-names : named "ch%d", where %d is the channel number ranging from zero
+                to the number of channels (DnFIFOs) minus one.
 
 Example:
 	usbhs: usb@e6590000 {

Documentation/devicetree/bindings/usb/twlxxxx-usb.txt

@@ -30,6 +30,9 @@ TWL4030 USB PHY AND COMPARATOR
  - usb_mode : The mode used by the phy to connect to the controller. "1"
    specifies "ULPI" mode and "2" specifies "CEA2011_3PIN" mode.
 
+If a sibling node is compatible "ti,twl4030-bci", then it will find
+this device and query it for USB power status.
+
 twl4030-usb {
 	compatible = "ti,twl4030-usb";
 	interrupts = < 10 4 >;

Documentation/usb/gadget-testing.txt

@@ -526,8 +526,6 @@ Except for ifname they can be written to until the function is linked to a
 configuration. The ifname is read-only and contains the name of the interface
 which was assigned by the net core, e. g. usb0.
 
-By default there can be only 1 RNDIS interface in the system.
-
 Testing the RNDIS function
 --------------------------
 
@@ -629,7 +627,7 @@ Function-specific configfs interface
 The function name to use when creating the function directory is "uac2".
 The uac2 function provides these attributes in its function directory:
 
-	chmask - capture channel mask
+	c_chmask - capture channel mask
 	c_srate - capture sampling rate
 	c_ssize - capture sample size (bytes)
 	p_chmask - playback channel mask

MAINTAINERS

@@ -10489,6 +10489,13 @@ S:	Maintained
 F:	Documentation/video4linux/zr364xx.txt
 F:	drivers/media/usb/zr364xx/
 
+ULPI BUS
+M:	Heikki Krogerus <[email protected]>
+L:	[email protected]
+S:	Maintained
+F:	drivers/usb/common/ulpi.c
+F:	include/linux/ulpi/
+
 USER-MODE LINUX (UML)
 M:	Jeff Dike <[email protected]>
 M:	Richard Weinberger <[email protected]>

drivers/phy/Kconfig

@@ -309,4 +309,11 @@ config PHY_QCOM_UFS
 	help
 	  Support for UFS PHY on QCOM chipsets.
 
+config PHY_TUSB1210
+	tristate "TI TUSB1210 ULPI PHY module"
+	depends on USB_ULPI_BUS
+	select GENERIC_PHY
+	help
+	  Support for TI TUSB1210 USB ULPI PHY.
+
 endmenu

drivers/phy/Makefile

@@ -40,3 +40,4 @@ obj-$(CONFIG_PHY_STIH41X_USB)		+= phy-stih41x-usb.o
 obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs.o
 obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs-qmp-20nm.o
 obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs-qmp-14nm.o
+obj-$(CONFIG_PHY_TUSB1210)		+= phy-tusb1210.o

drivers/phy/phy-sun4i-usb.c

@@ -30,6 +30,7 @@
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/phy/phy.h>
+#include <linux/phy/phy-sun4i-usb.h>
 #include <linux/platform_device.h>
 #include <linux/regulator/consumer.h>
 #include <linux/reset.h>
@@ -58,6 +59,7 @@
 #define PHY_OTG_FUNC_EN			0x28
 #define PHY_VBUS_DET_EN			0x29
 #define PHY_DISCON_TH_SEL		0x2a
+#define PHY_SQUELCH_DETECT		0x3c
 
 #define MAX_PHYS			3
 
@@ -204,6 +206,13 @@ static int sun4i_usb_phy_power_off(struct phy *_phy)
 	return 0;
 }
 
+void sun4i_usb_phy_set_squelch_detect(struct phy *_phy, bool enabled)
+{
+	struct sun4i_usb_phy *phy = phy_get_drvdata(_phy);
+
+	sun4i_usb_phy_write(phy, PHY_SQUELCH_DETECT, enabled ? 0 : 2, 2);
+}
+
 static struct phy_ops sun4i_usb_phy_ops = {
 	.init		= sun4i_usb_phy_init,
 	.exit		= sun4i_usb_phy_exit,

drivers/phy/phy-tusb1210.c

@@ -0,0 +1,153 @@
+/**
+ * tusb1210.c - TUSB1210 USB ULPI PHY driver
+ *
+ * Copyright (C) 2015 Intel Corporation
+ *
+ * Author: Heikki Krogerus <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/module.h>
+#include <linux/ulpi/driver.h>
+#include <linux/gpio/consumer.h>
+
+#include "ulpi_phy.h"
+
+#define TUSB1210_VENDOR_SPECIFIC2		0x80
+#define TUSB1210_VENDOR_SPECIFIC2_IHSTX_SHIFT	0
+#define TUSB1210_VENDOR_SPECIFIC2_ZHSDRV_SHIFT	4
+#define TUSB1210_VENDOR_SPECIFIC2_DP_SHIFT	6
+
+struct tusb1210 {
+	struct ulpi *ulpi;
+	struct phy *phy;
+	struct gpio_desc *gpio_reset;
+	struct gpio_desc *gpio_cs;
+	u8 vendor_specific2;
+};
+
+static int tusb1210_power_on(struct phy *phy)
+{
+	struct tusb1210 *tusb = phy_get_drvdata(phy);
+
+	gpiod_set_value_cansleep(tusb->gpio_reset, 1);
+	gpiod_set_value_cansleep(tusb->gpio_cs, 1);
+
+	/* Restore the optional eye diagram optimization value */
+	if (tusb->vendor_specific2)
+		ulpi_write(tusb->ulpi, TUSB1210_VENDOR_SPECIFIC2,
+			   tusb->vendor_specific2);
+
+	return 0;
+}
+
+static int tusb1210_power_off(struct phy *phy)
+{
+	struct tusb1210 *tusb = phy_get_drvdata(phy);
+
+	gpiod_set_value_cansleep(tusb->gpio_reset, 0);
+	gpiod_set_value_cansleep(tusb->gpio_cs, 0);
+
+	return 0;
+}
+
+static struct phy_ops phy_ops = {
+	.power_on = tusb1210_power_on,
+	.power_off = tusb1210_power_off,
+	.owner = THIS_MODULE,
+};
+
+static int tusb1210_probe(struct ulpi *ulpi)
+{
+	struct gpio_desc *gpio;
+	struct tusb1210 *tusb;
+	u8 val, reg;
+	int ret;
+
+	tusb = devm_kzalloc(&ulpi->dev, sizeof(*tusb), GFP_KERNEL);
+	if (!tusb)
+		return -ENOMEM;
+
+	gpio = devm_gpiod_get(&ulpi->dev, "reset");
+	if (!IS_ERR(gpio)) {
+		ret = gpiod_direction_output(gpio, 0);
+		if (ret)
+			return ret;
+		gpiod_set_value_cansleep(gpio, 1);
+		tusb->gpio_reset = gpio;
+	}
+
+	gpio = devm_gpiod_get(&ulpi->dev, "cs");
+	if (!IS_ERR(gpio)) {
+		ret = gpiod_direction_output(gpio, 0);
+		if (ret)
+			return ret;
+		gpiod_set_value_cansleep(gpio, 1);
+		tusb->gpio_cs = gpio;
+	}
+
+	/*
+	 * VENDOR_SPECIFIC2 register in TUSB1210 can be used for configuring eye
+	 * diagram optimization and DP/DM swap.
+	 */
+
+	/* High speed output drive strength configuration */
+	device_property_read_u8(&ulpi->dev, "ihstx", &val);
+	reg = val << TUSB1210_VENDOR_SPECIFIC2_IHSTX_SHIFT;
+
+	/* High speed output impedance configuration */
+	device_property_read_u8(&ulpi->dev, "zhsdrv", &val);
+	reg |= val << TUSB1210_VENDOR_SPECIFIC2_ZHSDRV_SHIFT;
+
+	/* DP/DM swap control */
+	device_property_read_u8(&ulpi->dev, "datapolarity", &val);
+	reg |= val << TUSB1210_VENDOR_SPECIFIC2_DP_SHIFT;
+
+	if (reg) {
+		ulpi_write(ulpi, TUSB1210_VENDOR_SPECIFIC2, reg);
+		tusb->vendor_specific2 = reg;
+	}
+
+	tusb->phy = ulpi_phy_create(ulpi, &phy_ops);
+	if (IS_ERR(tusb->phy))
+		return PTR_ERR(tusb->phy);
+
+	tusb->ulpi = ulpi;
+
+	phy_set_drvdata(tusb->phy, tusb);
+	ulpi_set_drvdata(ulpi, tusb);
+	return 0;
+}
+
+static void tusb1210_remove(struct ulpi *ulpi)
+{
+	struct tusb1210 *tusb = ulpi_get_drvdata(ulpi);
+
+	ulpi_phy_destroy(ulpi, tusb->phy);
+}
+
+#define TI_VENDOR_ID 0x0451
+
+static const struct ulpi_device_id tusb1210_ulpi_id[] = {
+	{ TI_VENDOR_ID, 0x1507, },
+	{ },
+};
+MODULE_DEVICE_TABLE(ulpi, tusb1210_ulpi_id);
+
+static struct ulpi_driver tusb1210_driver = {
+	.id_table = tusb1210_ulpi_id,
+	.probe = tusb1210_probe,
+	.remove = tusb1210_remove,
+	.driver = {
+		.name = "tusb1210",
+		.owner = THIS_MODULE,
+	},
+};
+
+module_ulpi_driver(tusb1210_driver);
+
+MODULE_AUTHOR("Intel Corporation");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("TUSB1210 ULPI PHY driver");

drivers/phy/ulpi_phy.h

@@ -0,0 +1,31 @@
+#include <linux/phy/phy.h>
+
+/**
+ * Helper that registers PHY for a ULPI device and adds a lookup for binding it
+ * and it's controller, which is always the parent.
+ */
+static inline struct phy
+*ulpi_phy_create(struct ulpi *ulpi, struct phy_ops *ops)
+{
+	struct phy *phy;
+	int ret;
+
+	phy = phy_create(&ulpi->dev, NULL, ops);
+	if (IS_ERR(phy))
+		return phy;
+
+	ret = phy_create_lookup(phy, "usb2-phy", dev_name(ulpi->dev.parent));
+	if (ret) {
+		phy_destroy(phy);
+		return ERR_PTR(ret);
+	}
+
+	return phy;
+}
+
+/* Remove a PHY that was created with ulpi_phy_create() and it's lookup. */
+static inline void ulpi_phy_destroy(struct ulpi *ulpi, struct phy *phy)
+{
+	phy_remove_lookup(phy, "usb2-phy", dev_name(ulpi->dev.parent));
+	phy_destroy(phy);
+}