Merge branch 'irq-core-for-linus' of git://git.kernel.org/pub/scm/lin…

…ux/kernel/git/tip/tip

Pull irq updates from Thomas Gleixner:
 "Nothing spectacular from the irq department this time:
   - overhaul of the crossbar chip driver
   - overhaul of the spear shirq chip driver
   - support for the atmel-aic chip
   - code move from arch to drivers
   - the usual tiny fixlets
   - two reverts worth to mention which undo the too simple attempt of
     supporting wakeup interrupts on shared interrupt lines"

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
  Revert "irq: Warn when shared interrupts do not match on NO_SUSPEND"
  Revert "PM / sleep / irq: Do not suspend wakeup interrupts"
  irq: Warn when shared interrupts do not match on NO_SUSPEND
  irqchip: atmel-aic: Define irq fixups for atmel SoCs
  irqchip: atmel-aic: Implement RTC irq fixup
  irqchip: atmel-aic: Add irq fixup infrastructure
  irqchip: atmel-aic: Add atmel AIC/AIC5 drivers
  irqchip: atmel-aic: Move binding doc to interrupt-controller directory
  genirq: generic chip: Export irq_map_generic_chip function
  PM / sleep / irq: Do not suspend wakeup interrupts
  irqchip: or1k-pic: Migrate from arch/openrisc/
  irqchip: crossbar: Allow for quirky hardware with direct hardwiring of GIC
  documentation: dt: omap: crossbar: Add description for interrupt consumer
  irqchip: crossbar: Introduce centralized check for crossbar write
  irqchip: crossbar: Introduce ti, max-crossbar-sources to identify valid crossbar mapping
  irqchip: crossbar: Add kerneldoc for crossbar_domain_unmap callback
  irqchip: crossbar: Set cb pointer to null in case of error
  irqchip: crossbar: Change the goto naming
  irqchip: crossbar: Return proper error value
  irqchip: crossbar: Fix kerneldoc warning
  ...

Documentation/devicetree/bindings/arm/omap/crossbar.txt

@@ -10,18 +10,54 @@ Required properties:
 - compatible : Should be "ti,irq-crossbar"
 - reg: Base address and the size of the crossbar registers.
 - ti,max-irqs: Total number of irqs available at the interrupt controller.
+- ti,max-crossbar-sources: Maximum number of crossbar sources that can be routed.
 - ti,reg-size: Size of a individual register in bytes. Every individual
 	    register is assumed to be of same size. Valid sizes are 1, 2, 4.
 - ti,irqs-reserved: List of the reserved irq lines that are not muxed using
 		 crossbar. These interrupt lines are reserved in the soc,
 		 so crossbar bar driver should not consider them as free
 		 lines.
 
+Optional properties:
+- ti,irqs-skip: This is similar to "ti,irqs-reserved", but these are for
+  SOC-specific hard-wiring of those irqs which unexpectedly bypasses the
+  crossbar. These irqs have a crossbar register, but still cannot be used.
+
+- ti,irqs-safe-map: integer which maps to a safe configuration to use
+  when the interrupt controller irq is unused (when not provided, default is 0)
+
 Examples:
 		crossbar_mpu: @4a020000 {
 			compatible = "ti,irq-crossbar";
 			reg = <0x4a002a48 0x130>;
 			ti,max-irqs = <160>;
+			ti,max-crossbar-sources = <400>;
 			ti,reg-size = <2>;
 			ti,irqs-reserved = <0 1 2 3 5 6 131 132 139 140>;
+			ti,irqs-skip = <10 133 139 140>;
 		};
+
+Consumer:
+========
+See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt and
+Documentation/devicetree/bindings/arm/gic.txt for further details.
+
+An interrupt consumer on an SoC using crossbar will use:
+	interrupts = <GIC_SPI request_number interrupt_level>
+When the request number is between 0 to that described by
+"ti,max-crossbar-sources", it is assumed to be a crossbar mapping. If the
+request_number is greater than "ti,max-crossbar-sources", then it is mapped as a
+quirky hardware mapping direct to GIC.
+
+Example:
+	device_x@0x4a023000 {
+		/* Crossbar 8 used */
+		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+		...
+	};
+
+	device_y@0x4a033000 {
+		/* Direct mapped GIC SPI 1 used */
+		interrupts = <GIC_SPI DIRECT_IRQ(1) IRQ_TYPE_LEVEL_HIGH>;
+		...
+	};

Documentation/devicetree/bindings/interrupt-controller/opencores,or1k-pic.txt

@@ -0,0 +1,23 @@
+OpenRISC 1000 Programmable Interrupt Controller
+
+Required properties:
+
+- compatible : should be "opencores,or1k-pic-level" for variants with
+  level triggered interrupt lines, "opencores,or1k-pic-edge" for variants with
+  edge triggered interrupt lines or "opencores,or1200-pic" for machines
+  with the non-spec compliant or1200 type implementation.
+
+  "opencores,or1k-pic" is also provided as an alias to "opencores,or1200-pic",
+  but this is only for backwards compatibility.
+
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. The value shall be 1.
+
+Example:
+
+intc: interrupt-controller {
+	compatible = "opencores,or1k-pic-level";
+	interrupt-controller;
+	#interrupt-cells = <1>;
+};

arch/openrisc/Kconfig

@@ -22,6 +22,7 @@ config OPENRISC
 	select GENERIC_STRNLEN_USER
 	select MODULES_USE_ELF_RELA
 	select HAVE_DEBUG_STACKOVERFLOW
+	select OR1K_PIC
 
 config MMU
 	def_bool y

arch/openrisc/include/asm/irq.h

@@ -24,4 +24,7 @@
 
 #define NO_IRQ		(-1)
 
+void handle_IRQ(unsigned int, struct pt_regs *);
+extern void set_handle_irq(void (*handle_irq)(struct pt_regs *));
+
 #endif /* __ASM_OPENRISC_IRQ_H__ */

arch/openrisc/kernel/irq.c

@@ -16,11 +16,10 @@
 
 #include <linux/interrupt.h>
 #include <linux/init.h>
-#include <linux/of.h>
 #include <linux/ftrace.h>
 #include <linux/irq.h>
+#include <linux/irqchip.h>
 #include <linux/export.h>
-#include <linux/irqdomain.h>
 #include <linux/irqflags.h>
 
 /* read interrupt enabled status */
@@ -37,150 +36,31 @@ void arch_local_irq_restore(unsigned long flags)
 }
 EXPORT_SYMBOL(arch_local_irq_restore);
 
-
-/* OR1K PIC implementation */
-
-/* We're a couple of cycles faster than the generic implementations with
- * these 'fast' versions.
- */
-
-static void or1k_pic_mask(struct irq_data *data)
-{
-	mtspr(SPR_PICMR, mfspr(SPR_PICMR) & ~(1UL << data->hwirq));
-}
-
-static void or1k_pic_unmask(struct irq_data *data)
-{
-	mtspr(SPR_PICMR, mfspr(SPR_PICMR) | (1UL << data->hwirq));
-}
-
-static void or1k_pic_ack(struct irq_data *data)
-{
-	/* EDGE-triggered interrupts need to be ack'ed in order to clear
-	 * the latch.
-	 * LEVEL-triggered interrupts do not need to be ack'ed; however,
-	 * ack'ing the interrupt has no ill-effect and is quicker than
-	 * trying to figure out what type it is...
-	 */
-
-	/* The OpenRISC 1000 spec says to write a 1 to the bit to ack the
-	 * interrupt, but the OR1200 does this backwards and requires a 0
-	 * to be written...
-	 */
-
-#ifdef CONFIG_OR1K_1200
-	/* There are two oddities with the OR1200 PIC implementation:
-	 * i)  LEVEL-triggered interrupts are latched and need to be cleared
-	 * ii) the interrupt latch is cleared by writing a 0 to the bit,
-	 *     as opposed to a 1 as mandated by the spec
-	 */
-
-	mtspr(SPR_PICSR, mfspr(SPR_PICSR) & ~(1UL << data->hwirq));
-#else
-	WARN(1, "Interrupt handling possibly broken\n");
-	mtspr(SPR_PICSR, (1UL << data->hwirq));
-#endif
-}
-
-static void or1k_pic_mask_ack(struct irq_data *data)
-{
-	/* Comments for pic_ack apply here, too */
-
-#ifdef CONFIG_OR1K_1200
-	mtspr(SPR_PICMR, mfspr(SPR_PICMR) & ~(1UL << data->hwirq));
-	mtspr(SPR_PICSR, mfspr(SPR_PICSR) & ~(1UL << data->hwirq));
-#else
-	WARN(1, "Interrupt handling possibly broken\n");
-	mtspr(SPR_PICMR, (1UL << data->hwirq));
-	mtspr(SPR_PICSR, (1UL << data->hwirq));
-#endif
-}
-
-#if 0
-static int or1k_pic_set_type(struct irq_data *data, unsigned int flow_type)
-{
-	/* There's nothing to do in the PIC configuration when changing
-	 * flow type.  Level and edge-triggered interrupts are both
-	 * supported, but it's PIC-implementation specific which type
-	 * is handled. */
-
-	return irq_setup_alt_chip(data, flow_type);
-}
-#endif
-
-static struct irq_chip or1k_dev = {
-	.name = "or1k-PIC",
-	.irq_unmask = or1k_pic_unmask,
-	.irq_mask = or1k_pic_mask,
-	.irq_ack = or1k_pic_ack,
-	.irq_mask_ack = or1k_pic_mask_ack,
-};
-
-static struct irq_domain *root_domain;
-
-static inline int pic_get_irq(int first)
-{
-	int hwirq;
-
-	hwirq = ffs(mfspr(SPR_PICSR) >> first);
-	if (!hwirq)
-		return NO_IRQ;
-	else
-		hwirq = hwirq + first -1;
-
-	return irq_find_mapping(root_domain, hwirq);
-}
-
-
-static int or1k_map(struct irq_domain *d, unsigned int irq, irq_hw_number_t hw)
+void __init init_IRQ(void)
 {
-	irq_set_chip_and_handler_name(irq, &or1k_dev,
-				      handle_level_irq, "level");
-	irq_set_status_flags(irq, IRQ_LEVEL | IRQ_NOPROBE);
-
-	return 0;
+	irqchip_init();
 }
 
-static const struct irq_domain_ops or1k_irq_domain_ops = {
-	.xlate = irq_domain_xlate_onecell,
-	.map = or1k_map,
-};
-
-/*
- * This sets up the IRQ domain for the PIC built in to the OpenRISC
- * 1000 CPU.  This is the "root" domain as these are the interrupts
- * that directly trigger an exception in the CPU.
- */
-static void __init or1k_irq_init(void)
-{
-	struct device_node *intc = NULL;
-
-	/* The interrupt controller device node is mandatory */
-	intc = of_find_compatible_node(NULL, NULL, "opencores,or1k-pic");
-	BUG_ON(!intc);
-
-	/* Disable all interrupts until explicitly requested */
-	mtspr(SPR_PICMR, (0UL));
-
-	root_domain = irq_domain_add_linear(intc, 32,
-					    &or1k_irq_domain_ops, NULL);
-}
+static void (*handle_arch_irq)(struct pt_regs *);
 
-void __init init_IRQ(void)
+void __init set_handle_irq(void (*handle_irq)(struct pt_regs *))
 {
-	or1k_irq_init();
+	handle_arch_irq = handle_irq;
 }
 
-void __irq_entry do_IRQ(struct pt_regs *regs)
+void handle_IRQ(unsigned int irq, struct pt_regs *regs)
 {
-	int irq = -1;
 	struct pt_regs *old_regs = set_irq_regs(regs);
 
 	irq_enter();
 
-	while ((irq = pic_get_irq(irq + 1)) != NO_IRQ)
-		generic_handle_irq(irq);
+	generic_handle_irq(irq);
 
 	irq_exit();
 	set_irq_regs(old_regs);
 }
+
+void __irq_entry do_IRQ(struct pt_regs *regs)
+{
+	handle_arch_irq(regs);
+}

drivers/irqchip/Kconfig

@@ -35,6 +35,20 @@ config ARM_VIC_NR
 	  The maximum number of VICs available in the system, for
 	  power management.
 
+config ATMEL_AIC_IRQ
+	bool
+	select GENERIC_IRQ_CHIP
+	select IRQ_DOMAIN
+	select MULTI_IRQ_HANDLER
+	select SPARSE_IRQ
+
+config ATMEL_AIC5_IRQ
+	bool
+	select GENERIC_IRQ_CHIP
+	select IRQ_DOMAIN
+	select MULTI_IRQ_HANDLER
+	select SPARSE_IRQ
+
 config BRCMSTB_L2_IRQ
 	bool
 	depends on ARM
@@ -58,6 +72,10 @@ config CLPS711X_IRQCHIP
 	select SPARSE_IRQ
 	default y
 
+config OR1K_PIC
+	bool
+	select IRQ_DOMAIN
+
 config ORION_IRQCHIP
 	bool
 	select IRQ_DOMAIN

drivers/irqchip/Makefile

@@ -11,6 +11,7 @@ obj-$(CONFIG_METAG)			+= irq-metag-ext.o
 obj-$(CONFIG_METAG_PERFCOUNTER_IRQS)	+= irq-metag.o
 obj-$(CONFIG_ARCH_MOXART)		+= irq-moxart.o
 obj-$(CONFIG_CLPS711X_IRQCHIP)		+= irq-clps711x.o
+obj-$(CONFIG_OR1K_PIC)			+= irq-or1k-pic.o
 obj-$(CONFIG_ORION_IRQCHIP)		+= irq-orion.o
 obj-$(CONFIG_ARCH_SUNXI)		+= irq-sun4i.o
 obj-$(CONFIG_ARCH_SUNXI)		+= irq-sunxi-nmi.o
@@ -19,6 +20,8 @@ obj-$(CONFIG_ARM_GIC)			+= irq-gic.o irq-gic-common.o
 obj-$(CONFIG_ARM_GIC_V3)		+= irq-gic-v3.o irq-gic-common.o
 obj-$(CONFIG_ARM_NVIC)			+= irq-nvic.o
 obj-$(CONFIG_ARM_VIC)			+= irq-vic.o
+obj-$(CONFIG_ATMEL_AIC_IRQ)		+= irq-atmel-aic-common.o irq-atmel-aic.o
+obj-$(CONFIG_ATMEL_AIC5_IRQ)	+= irq-atmel-aic-common.o irq-atmel-aic5.o
 obj-$(CONFIG_IMGPDC_IRQ)		+= irq-imgpdc.o
 obj-$(CONFIG_SIRF_IRQ)			+= irq-sirfsoc.o
 obj-$(CONFIG_RENESAS_INTC_IRQPIN)	+= irq-renesas-intc-irqpin.o