media: smiapp: Move definitions under driver directory

include/media/i2c/smiapp.h was meant to serve systems where the sensor is enumerated through platform data. That's no longer necessary, hopefully not even in out-of-tree use cases. Move the definitions to the appropriate headers. Signed-off-by: Sakari Ailus <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
josf · Feb 27, 2020 · 7cbeb2e · 7cbeb2e
1 parent 354d5ab
commit 7cbeb2e
Show file tree

Hide file tree

Showing 3 changed files with 47 additions and 64 deletions.
diff --git a/drivers/media/i2c/smiapp/smiapp-reg.h b/drivers/media/i2c/smiapp/smiapp-reg.h
@@ -35,6 +35,10 @@
 #define SMIAPP_FLASH_MODE_CAPABILITY_SINGLE_STROBE	BIT(0)
 #define SMIAPP_FLASH_MODE_CAPABILITY_MULTIPLE_STROBE	BIT(1)
 
+#define SMIAPP_CSI_SIGNALLING_MODE_CCP2_DATA_CLOCK	0
+#define SMIAPP_CSI_SIGNALLING_MODE_CCP2_DATA_STROBE	1
+#define SMIAPP_CSI_SIGNALLING_MODE_CSI2			2
+
 #define SMIAPP_DPHY_CTRL_AUTOMATIC			0
 /* DPHY control based on REQUESTED_LINK_BIT_RATE_MBPS */
 #define SMIAPP_DPHY_CTRL_UI				1

diff --git a/drivers/media/i2c/smiapp/smiapp.h b/drivers/media/i2c/smiapp/smiapp.h
@@ -14,7 +14,6 @@
 #include <linux/mutex.h>
 #include <media/v4l2-ctrls.h>
 #include <media/v4l2-subdev.h>
-#include <media/i2c/smiapp.h>
 
 #include "smiapp-pll.h"
 #include "smiapp-reg.h"
@@ -42,6 +41,49 @@
 
 #define SMIAPP_COLOUR_COMPONENTS	4
 
+#define SMIAPP_NAME		"smiapp"
+
+#define SMIAPP_DFL_I2C_ADDR	(0x20 >> 1) /* Default I2C Address */
+#define SMIAPP_ALT_I2C_ADDR	(0x6e >> 1) /* Alternate I2C Address */
+
+/*
+ * Sometimes due to board layout considerations the camera module can be
+ * mounted rotated. The typical rotation used is 180 degrees which can be
+ * corrected by giving a default H-FLIP and V-FLIP in the sensor readout.
+ * FIXME: rotation also changes the bayer pattern.
+ */
+enum smiapp_module_board_orient {
+	SMIAPP_MODULE_BOARD_ORIENT_0 = 0,
+	SMIAPP_MODULE_BOARD_ORIENT_180,
+};
+
+struct smiapp_flash_strobe_parms {
+	u8 mode;
+	u32 strobe_width_high_us;
+	u16 strobe_delay;
+	u16 stobe_start_point;
+	u8 trigger;
+};
+
+struct smiapp_hwconfig {
+	/*
+	 * Change the cci address if i2c_addr_alt is set.
+	 * Both default and alternate cci addr need to be present
+	 */
+	unsigned short i2c_addr_dfl;	/* Default i2c addr */
+	unsigned short i2c_addr_alt;	/* Alternate i2c addr */
+
+	uint32_t ext_clk;		/* sensor external clk */
+
+	unsigned int lanes;		/* Number of CSI-2 lanes */
+	uint32_t csi_signalling_mode;	/* SMIAPP_CSI_SIGNALLING_MODE_* */
+	uint64_t *op_sys_clock;
+
+	enum smiapp_module_board_orient module_board_orient;
+
+	struct smiapp_flash_strobe_parms *strobe_setup;
+};
+
 #include "smiapp-limits.h"
 
 struct smiapp_quirk;

diff --git a/include/media/i2c/smiapp.h b/include/media/i2c/smiapp.h