Merge tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/ker…

…nel/git/arm/arm-soc Pull ARM SoC platform updates (part 3) from Arnd Bergmann: "This is the third and smallest of the SoC specific updates. Changes include: - SMP support for the Xilinx zynq platform - Smaller imx changes - LPAE support for mvebu - Moving the orion5x, kirkwood, dove and mvebu platforms to a common "mbus" driver for their internal devices. It would be good to get feedback on the location of the "mbus" driver. Since this is used on multiple platforms may potentially get shared with other architectures (powerpc and arm64), it was moved to drivers/bus/. We expect other similar drivers to get moved to the same place in order to avoid creating more top-level directories under drivers/ or cluttering up the messy drivers/misc/ even more." * tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits) ARM: imx: reset_controller may be disabled ARM: mvebu: Align the internal registers virtual base to support LPAE ARM: mvebu: Limit the DMA zone when LPAE is selected arm: plat-orion: remove addr-map code arm: mach-mv78xx0: convert to use the mvebu-mbus driver arm: mach-orion5x: convert to use mvebu-mbus driver arm: mach-dove: convert to use mvebu-mbus driver arm: mach-kirkwood: convert to use mvebu-mbus driver arm: mach-mvebu: convert to use mvebu-mbus driver ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock ARM i.MX53: tve_di clock is not part of the CCM, but of TVE ARM i.MX53: make tve_ext_sel propagate rate change to PLL ARM i.MX53: Remove unused tve_gate clkdev entry ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree ARM: i.MX5: Add PATA and SRTC clocks ARM: imx: do not bring up unavailable cores ARM: imx: add initial imx6dl support ARM: imx1: mm: add call to mxc_device_init ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS ...
josf · May 7, 2013 · fcba914 · fcba914
2 parents a8c4b90 + 5c5f042
commit fcba914
Show file tree

Hide file tree

Showing 95 changed files with 2,256 additions and 1,001 deletions.
diff --git a/Documentation/devicetree/bindings/clock/imx5-clock.txt b/Documentation/devicetree/bindings/clock/imx5-clock.txt
@@ -38,7 +38,6 @@ clocks and IDs.
 	usb_phy_podf		23
 	cpu_podf		24
 	di_pred			25
-	tve_di			26
 	tve_s			27
 	uart1_ipg_gate		28
 	uart1_per_gate		29
@@ -172,6 +171,19 @@ clocks and IDs.
 	can1_serial_gate	157
 	can1_ipg_gate		158
 	owire_gate		159
+	gpu3d_s			160
+	gpu2d_s			161
+	gpu3d_gate		162
+	gpu2d_gate		163
+	garb_gate		164
+	cko1_sel		165
+	cko1_podf		166
+	cko1			167
+	cko2_sel		168
+	cko2_podf		169
+	cko2			170
+	srtc_gate		171
+	pata_gate		172
 
 Examples (for mx53):
 

diff --git a/Documentation/devicetree/bindings/clock/imx6q-clock.txt b/Documentation/devicetree/bindings/clock/imx6q-clock.txt
@@ -205,6 +205,9 @@ clocks and IDs.
 	enet_ref		190
 	usbphy1_gate		191
 	usbphy2_gate		192
+	pll4_post_div		193
+	pll5_post_div		194
+	pll5_video_div		195
 
 Examples:
 

diff --git a/Documentation/devicetree/bindings/reset/fsl,imx-src.txt b/Documentation/devicetree/bindings/reset/fsl,imx-src.txt
@@ -0,0 +1,49 @@
+Freescale i.MX System Reset Controller
+======================================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+- compatible: Should be "fsl,<chip>-src"
+- reg: should be register base and length as documented in the
+  datasheet
+- interrupts: Should contain SRC interrupt and CPU WDOG interrupt,
+  in this order.
+- #reset-cells: 1, see below
+
+example:
+
+src: src@020d8000 {
+        compatible = "fsl,imx6q-src";
+        reg = <0x020d8000 0x4000>;
+        interrupts = <0 91 0x04 0 96 0x04>;
+        #reset-cells = <1>;
+};
+
+Specifying reset lines connected to IP modules
+==============================================
+
+The system reset controller can be used to reset the GPU, VPU,
+IPU, and OpenVG IP modules on i.MX5 and i.MX6 ICs. Those device
+nodes should specify the reset line on the SRC in their resets
+property, containing a phandle to the SRC device node and a
+RESET_INDEX specifying which module to reset, as described in
+reset.txt
+
+example:
+
+        ipu1: ipu@02400000 {
+                resets = <&src 2>;
+        };
+        ipu2: ipu@02800000 {
+                resets = <&src 4>;
+        };
+
+The following RESET_INDEX values are valid for i.MX5:
+GPU_RESET     0
+VPU_RESET     1
+IPU1_RESET    2
+OPEN_VG_RESET 3
+The following additional RESET_INDEX value is valid for i.MX6:
+IPU2_RESET    4
diff --git a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt
@@ -8,6 +8,8 @@ Required properties:
 - interrupts: Should contain sync interrupt and error interrupt,
   in this order.
 - #crtc-cells: 1, See below
+- resets: phandle pointing to the system reset controller and
+          reset line index, see reset/fsl,imx-src.txt for details
 
 example:
 
@@ -16,6 +18,7 @@ ipu: ipu@18000000 {
 	compatible = "fsl,imx53-ipu";
 	reg = <0x18000000 0x080000000>;
 	interrupts = <11 10>;
+	resets = <&src 2>;
 };
 
 Parallel display support

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
@@ -498,6 +498,7 @@ config ARCH_DOVE
 	select PINCTRL_DOVE
 	select PLAT_ORION_LEGACY
 	select USB_ARCH_HAS_EHCI
+	select MVEBU_MBUS
 	help
 	  Support for the Marvell Dove SoC 88AP510
 
@@ -511,6 +512,7 @@ config ARCH_KIRKWOOD
 	select PINCTRL
 	select PINCTRL_KIRKWOOD
 	select PLAT_ORION_LEGACY
+	select MVEBU_MBUS
 	help
 	  Support for the following Marvell Kirkwood series SoCs:
 	  88F6180, 88F6192 and 88F6281.
@@ -522,6 +524,7 @@ config ARCH_MV78XX0
 	select GENERIC_CLOCKEVENTS
 	select PCI
 	select PLAT_ORION_LEGACY
+	select MVEBU_MBUS
 	help
 	  Support for the following Marvell MV78xx0 series SoCs:
 	  MV781x0, MV782x0.
@@ -534,6 +537,7 @@ config ARCH_ORION5X
 	select GENERIC_CLOCKEVENTS
 	select PCI
 	select PLAT_ORION_LEGACY
+	select MVEBU_MBUS
 	help
 	  Support for the following Marvell Orion 5x series SoCs:
 	  Orion-1 (5181), Orion-VoIP (5181L), Orion-NAS (5182),

diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
@@ -245,11 +245,11 @@ choice
 		  on i.MX53.
 
 	config DEBUG_IMX6Q_UART
-		bool "i.MX6Q Debug UART"
+		bool "i.MX6Q/DL Debug UART"
 		depends on SOC_IMX6Q
 		help
 		  Say Y here if you want kernel low-level debugging support
-		  on i.MX6Q.
+		  on i.MX6Q/DL.
 
 	config DEBUG_MMP_UART2
 		bool "Kernel low-level debugging message via MMP UART2"

diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/armada-370-xp.dtsi
@@ -73,11 +73,6 @@
 			       clocks = <&coreclk 2>;
 		};
 
-		addr-decoding@d0020000 {
-			compatible = "marvell,armada-addr-decoding-controller";
-			reg = <0xd0020000 0x258>;
-		};
-
 		sata@d00a0000 {
 			compatible = "marvell,orion-sata";
 			reg = <0xd00a0000 0x2400>;

diff --git a/arch/arm/boot/dts/zynq-7000.dtsi b/arch/arm/boot/dts/zynq-7000.dtsi
@@ -136,5 +136,12 @@
 			clock-names = "cpu_1x";
 			clock-ranges;
 		};
+		scutimer: scutimer@f8f00600 {
+			interrupt-parent = <&intc>;
+			interrupts = < 1 13 0x301 >;
+			compatible = "arm,cortex-a9-twd-timer";
+			reg = < 0xf8f00600 0x20 >;
+			clocks = <&cpu_clk 1>;
+		} ;
 	};
 };
diff --git a/arch/arm/configs/imx_v4_v5_defconfig b/arch/arm/configs/imx_v4_v5_defconfig
@@ -109,6 +109,7 @@ CONFIG_I2C_IMX=y
 CONFIG_SPI=y
 CONFIG_SPI_IMX=y
 CONFIG_SPI_SPIDEV=y
+CONFIG_GPIO_SYSFS=y
 CONFIG_W1=y
 CONFIG_W1_MASTER_MXC=y
 CONFIG_W1_SLAVE_THERM=y

diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
@@ -9,6 +9,7 @@ CONFIG_CGROUPS=y
 CONFIG_RELAY=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EXPERT=y
+CONFIG_PERF_EVENTS=y
 # CONFIG_SLUB_DEBUG is not set
 # CONFIG_COMPAT_BRK is not set
 CONFIG_MODULES=y

diff --git a/arch/arm/include/debug/mvebu.S b/arch/arm/include/debug/mvebu.S
@@ -12,7 +12,7 @@
 */
 
 #define ARMADA_370_XP_REGS_PHYS_BASE	0xd0000000
-#define ARMADA_370_XP_REGS_VIRT_BASE	0xfeb00000
+#define ARMADA_370_XP_REGS_VIRT_BASE	0xfec00000
 
 	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =ARMADA_370_XP_REGS_PHYS_BASE

diff --git a/arch/arm/mach-dove/Makefile b/arch/arm/mach-dove/Makefile
@@ -1,4 +1,4 @@
-obj-y				+= common.o addr-map.o irq.o
+obj-y				+= common.o irq.o
 obj-$(CONFIG_DOVE_LEGACY)	+= mpp.o
 obj-$(CONFIG_PCI)		+= pcie.o
 obj-$(CONFIG_MACH_DOVE_DB)	+= dove-db-setup.o

diff --git a/arch/arm/mach-dove/addr-map.c b/arch/arm/mach-dove/addr-map.c
diff --git a/arch/arm/mach-dove/board-dt.c b/arch/arm/mach-dove/board-dt.c
@@ -64,7 +64,7 @@ static void __init dove_dt_init(void)
 #ifdef CONFIG_CACHE_TAUROS2
 	tauros2_init(0);
 #endif
-	dove_setup_cpu_mbus();
+	dove_setup_cpu_wins();
 
 	/* Setup root of clk tree */
 	dove_of_clk_init();