Merge git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless…

…-next

Documentation/feature-removal-schedule.txt

@@ -534,6 +534,18 @@ Who:	Kees Cook <[email protected]>
 
 ----------------------------
 
+What:	Removing the pn544 raw driver.
+When:	3.6
+Why:	With the introduction of the NFC HCI and SHDL kernel layers, pn544.c
+	is being replaced by pn544_hci.c which is accessible through the netlink
+	and socket NFC APIs. Moreover, pn544.c is outdated and does not seem to
+	work properly with the latest Android stacks.
+	Having 2 drivers for the same hardware is confusing and as such we
+	should only keep the one following the kernel NFC APIs.
+Who:	Samuel Ortiz <[email protected]>
+
+----------------------------
+
 What:	setitimer accepts user NULL pointer (value)
 When:	3.6
 Why:	setitimer is not returning -EFAULT if user pointer is NULL. This

Documentation/nfc/nfc-hci.txt

@@ -22,9 +22,9 @@ response to arrive.
 HCI events can also be received from the host controller. They will be handled
 and a translation will be forwarded to NFC Core as needed.
 HCI uses 2 execution contexts:
-- one if for executing commands : nfc_hci_msg_tx_work(). Only one command
+- one for executing commands : nfc_hci_msg_tx_work(). Only one command
 can be executing at any given moment.
-- one if for dispatching received events and responses : nfc_hci_msg_rx_work()
+- one for dispatching received events and commands : nfc_hci_msg_rx_work().
 
 HCI Session initialization:
 ---------------------------
@@ -52,18 +52,42 @@ entry points:
 struct nfc_hci_ops {
 	int (*open)(struct nfc_hci_dev *hdev);
 	void (*close)(struct nfc_hci_dev *hdev);
+	int (*hci_ready) (struct nfc_hci_dev *hdev);
 	int (*xmit)(struct nfc_hci_dev *hdev, struct sk_buff *skb);
 	int (*start_poll)(struct nfc_hci_dev *hdev, u32 protocols);
 	int (*target_from_gate)(struct nfc_hci_dev *hdev, u8 gate,
 				struct nfc_target *target);
+	int (*complete_target_discovered) (struct nfc_hci_dev *hdev, u8 gate,
+					   struct nfc_target *target);
+	int (*data_exchange) (struct nfc_hci_dev *hdev,
+			      struct nfc_target *target,
+			      struct sk_buff *skb, struct sk_buff **res_skb);
+	int (*check_presence)(struct nfc_hci_dev *hdev,
+			      struct nfc_target *target);
 };
 
-open() and close() shall turn the hardware on and off. xmit() shall simply
-write a frame to the chip. start_poll() is an optional entrypoint that shall
-set the hardware in polling mode. This must be implemented only if the hardware
-uses proprietary gates or a mechanism slightly different from the HCI standard.
-target_from_gate() is another optional entrypoint to return the protocols
+- open() and close() shall turn the hardware on and off.
+- hci_ready() is an optional entry point that is called right after the hci
+session has been set up. The driver can use it to do additional initialization
+that must be performed using HCI commands.
+- xmit() shall simply write a frame to the chip.
+- start_poll() is an optional entrypoint that shall set the hardware in polling
+mode. This must be implemented only if the hardware uses proprietary gates or a
+mechanism slightly different from the HCI standard.
+- target_from_gate() is an optional entrypoint to return the nfc protocols
 corresponding to a proprietary gate.
+- complete_target_discovered() is an optional entry point to let the driver
+perform additional proprietary processing necessary to auto activate the
+discovered target.
+- data_exchange() must be implemented by the driver if proprietary HCI commands
+are required to send data to the tag. Some tag types will require custom
+commands, others can be written to using the standard HCI commands. The driver
+can check the tag type and either do proprietary processing, or return 1 to ask
+for standard processing.
+- check_presence() is an optional entry point that will be called regularly
+by the core to check that an activated tag is still in the field. If this is
+not implemented, the core will not be able to push tag_lost events to the user
+space
 
 On the rx path, the driver is responsible to push incoming HCP frames to HCI
 using nfc_hci_recv_frame(). HCI will take care of re-aggregation and handling
@@ -99,7 +123,8 @@ fast, cannot sleep. stores incoming frames into an shdlc rx queue
 handles shdlc rx & tx queues. Dispatches HCI cmd responses.
 
 - HCI Tx Cmd worker (MSGTXWQ)
-Serialize execution of HCI commands. Complete execution in case of resp timeout.
+Serializes execution of HCI commands. Completes execution in case of response
+timeout.
 
 - HCI Rx worker (MSGRXWQ)
 Dispatches incoming HCI commands or events.
@@ -133,11 +158,11 @@ able to complete the command with a timeout error if no response arrive.
 SMW context gets scheduled and invokes nfc_shdlc_sm_work(). This function
 handles shdlc framing in and out. It uses the driver xmit to send frames and
 receives incoming frames in an skb queue filled from the driver IRQ handler.
-SHDLC I(nformation) frames payload are HCP fragments. They are agregated to
+SHDLC I(nformation) frames payload are HCP fragments. They are aggregated to
 form complete HCI frames, which can be a response, command, or event.
 
 HCI Responses are dispatched immediately from this context to unblock
-waiting command execution. Reponse processing involves invoking the completion
+waiting command execution. Response processing involves invoking the completion
 callback that was provided by nfc_hci_msg_tx_work() when it sent the command.
 The completion callback will then wake the syscall context.
 

arch/mips/bcm47xx/setup.c

@@ -90,6 +90,7 @@ static int bcm47xx_get_sprom_ssb(struct ssb_bus *bus, struct ssb_sprom *out)
 	char prefix[10];
 
 	if (bus->bustype == SSB_BUSTYPE_PCI) {
+		memset(out, 0, sizeof(struct ssb_sprom));
 		snprintf(prefix, sizeof(prefix), "pci/%u/%u/",
 			 bus->host_pci->bus->number + 1,
 			 PCI_SLOT(bus->host_pci->devfn));
@@ -109,15 +110,9 @@ static int bcm47xx_get_invariants(struct ssb_bus *bus,
 	/* Fill boardinfo structure */
 	memset(&(iv->boardinfo), 0 , sizeof(struct ssb_boardinfo));
 
-	if (nvram_getenv("boardvendor", buf, sizeof(buf)) >= 0)
-		iv->boardinfo.vendor = (u16)simple_strtoul(buf, NULL, 0);
-	else
-		iv->boardinfo.vendor = SSB_BOARDVENDOR_BCM;
-	if (nvram_getenv("boardtype", buf, sizeof(buf)) >= 0)
-		iv->boardinfo.type = (u16)simple_strtoul(buf, NULL, 0);
-	if (nvram_getenv("boardrev", buf, sizeof(buf)) >= 0)
-		iv->boardinfo.rev = (u16)simple_strtoul(buf, NULL, 0);
+	bcm47xx_fill_ssb_boardinfo(&iv->boardinfo, NULL);
 
+	memset(&iv->sprom, 0, sizeof(struct ssb_sprom));
 	bcm47xx_fill_sprom(&iv->sprom, NULL);
 
 	if (nvram_getenv("cardbus", buf, sizeof(buf)) >= 0)
@@ -166,12 +161,14 @@ static int bcm47xx_get_sprom_bcma(struct bcma_bus *bus, struct ssb_sprom *out)
 
 	switch (bus->hosttype) {
 	case BCMA_HOSTTYPE_PCI:
+		memset(out, 0, sizeof(struct ssb_sprom));
 		snprintf(prefix, sizeof(prefix), "pci/%u/%u/",
 			 bus->host_pci->bus->number + 1,
 			 PCI_SLOT(bus->host_pci->devfn));
 		bcm47xx_fill_sprom(out, prefix);
 		return 0;
 	case BCMA_HOSTTYPE_SOC:
+		memset(out, 0, sizeof(struct ssb_sprom));
 		bcm47xx_fill_sprom_ethernet(out, NULL);
 		core = bcma_find_core(bus, BCMA_CORE_80211);
 		if (core) {
@@ -197,6 +194,8 @@ static void __init bcm47xx_register_bcma(void)
 	err = bcma_host_soc_register(&bcm47xx_bus.bcma);
 	if (err)
 		panic("Failed to initialize BCMA bus (err %d)", err);
+
+	bcm47xx_fill_bcma_boardinfo(&bcm47xx_bus.bcma.bus.boardinfo, NULL);
 }
 #endif
 

arch/mips/bcm47xx/sprom.c

@@ -165,6 +165,8 @@ static void bcm47xx_fill_sprom_r1234589(struct ssb_sprom *sprom,
 					const char *prefix)
 {
 	nvram_read_u16(prefix, NULL, "boardrev", &sprom->board_rev, 0);
+	if (!sprom->board_rev)
+		nvram_read_u16(NULL, NULL, "boardrev", &sprom->board_rev, 0);
 	nvram_read_u16(prefix, NULL, "boardnum", &sprom->board_num, 0);
 	nvram_read_u8(prefix, NULL, "ledbh0", &sprom->gpio0, 0xff);
 	nvram_read_u8(prefix, NULL, "ledbh1", &sprom->gpio1, 0xff);
@@ -555,8 +557,6 @@ void bcm47xx_fill_sprom_ethernet(struct ssb_sprom *sprom, const char *prefix)
 
 void bcm47xx_fill_sprom(struct ssb_sprom *sprom, const char *prefix)
 {
-	memset(sprom, 0, sizeof(struct ssb_sprom));
-
 	bcm47xx_fill_sprom_ethernet(sprom, prefix);
 
 	nvram_read_u8(prefix, NULL, "sromrev", &sprom->revision, 0);
@@ -618,3 +618,27 @@ void bcm47xx_fill_sprom(struct ssb_sprom *sprom, const char *prefix)
 		bcm47xx_fill_sprom_r1(sprom, prefix);
 	}
 }
+
+#ifdef CONFIG_BCM47XX_SSB
+void bcm47xx_fill_ssb_boardinfo(struct ssb_boardinfo *boardinfo,
+				const char *prefix)
+{
+	nvram_read_u16(prefix, NULL, "boardvendor", &boardinfo->vendor, 0);
+	if (!boardinfo->vendor)
+		boardinfo->vendor = SSB_BOARDVENDOR_BCM;
+
+	nvram_read_u16(prefix, NULL, "boardtype", &boardinfo->type, 0);
+}
+#endif
+
+#ifdef CONFIG_BCM47XX_BCMA
+void bcm47xx_fill_bcma_boardinfo(struct bcma_boardinfo *boardinfo,
+				 const char *prefix)
+{
+	nvram_read_u16(prefix, NULL, "boardvendor", &boardinfo->vendor, 0);
+	if (!boardinfo->vendor)
+		boardinfo->vendor = SSB_BOARDVENDOR_BCM;
+
+	nvram_read_u16(prefix, NULL, "boardtype", &boardinfo->type, 0);
+}
+#endif

arch/mips/include/asm/mach-bcm47xx/bcm47xx.h

@@ -47,4 +47,13 @@ extern enum bcm47xx_bus_type bcm47xx_bus_type;
 void bcm47xx_fill_sprom(struct ssb_sprom *sprom, const char *prefix);
 void bcm47xx_fill_sprom_ethernet(struct ssb_sprom *sprom, const char *prefix);
 
+#ifdef CONFIG_BCM47XX_SSB
+void bcm47xx_fill_ssb_boardinfo(struct ssb_boardinfo *boardinfo,
+				const char *prefix);
+#endif
+#ifdef CONFIG_BCM47XX_BCMA
+void bcm47xx_fill_bcma_boardinfo(struct bcma_boardinfo *boardinfo,
+				 const char *prefix);
+#endif
+
 #endif /* __ASM_BCM47XX_H */

drivers/bcma/core.c

@@ -30,6 +30,7 @@ void bcma_core_disable(struct bcma_device *core, u32 flags)
 	udelay(10);
 
 	bcma_awrite32(core, BCMA_RESET_CTL, BCMA_RESET_CTL_RESET);
+	bcma_aread32(core, BCMA_RESET_CTL);
 	udelay(1);
 }
 EXPORT_SYMBOL_GPL(bcma_core_disable);
@@ -77,7 +78,7 @@ void bcma_core_set_clockmode(struct bcma_device *core,
 			pr_err("HT force timeout\n");
 		break;
 	case BCMA_CLKMODE_DYNAMIC:
-		pr_warn("Dynamic clockmode not supported yet!\n");
+		bcma_set32(core, BCMA_CLKCTLST, ~BCMA_CLKCTLST_FORCEHT);
 		break;
 	}
 }

drivers/bcma/driver_pci.c

@@ -24,14 +24,12 @@ u32 bcma_pcie_read(struct bcma_drv_pci *pc, u32 address)
 	return pcicore_read32(pc, BCMA_CORE_PCI_PCIEIND_DATA);
 }
 
-#if 0
 static void bcma_pcie_write(struct bcma_drv_pci *pc, u32 address, u32 data)
 {
 	pcicore_write32(pc, BCMA_CORE_PCI_PCIEIND_ADDR, address);
 	pcicore_read32(pc, BCMA_CORE_PCI_PCIEIND_ADDR);
 	pcicore_write32(pc, BCMA_CORE_PCI_PCIEIND_DATA, data);
 }
-#endif
 
 static void bcma_pcie_mdio_set_phy(struct bcma_drv_pci *pc, u8 phy)
 {
@@ -170,13 +168,50 @@ static void bcma_pcicore_serdes_workaround(struct bcma_drv_pci *pc)
 		                     tmp & ~BCMA_CORE_PCI_PLL_CTRL_FREQDET_EN);
 }
 
+static void bcma_core_pci_fixcfg(struct bcma_drv_pci *pc)
+{
+	struct bcma_device *core = pc->core;
+	u16 val16, core_index;
+	uint regoff;
+
+	regoff = BCMA_CORE_PCI_SPROM(BCMA_CORE_PCI_SPROM_PI_OFFSET);
+	core_index = (u16)core->core_index;
+
+	val16 = pcicore_read16(pc, regoff);
+	if (((val16 & BCMA_CORE_PCI_SPROM_PI_MASK) >> BCMA_CORE_PCI_SPROM_PI_SHIFT)
+	     != core_index) {
+		val16 = (core_index << BCMA_CORE_PCI_SPROM_PI_SHIFT) |
+			(val16 & ~BCMA_CORE_PCI_SPROM_PI_MASK);
+		pcicore_write16(pc, regoff, val16);
+	}
+}
+
+/* Fix MISC config to allow coming out of L2/L3-Ready state w/o PRST */
+/* Needs to happen when coming out of 'standby'/'hibernate' */
+static void bcma_core_pci_config_fixup(struct bcma_drv_pci *pc)
+{
+	u16 val16;
+	uint regoff;
+
+	regoff = BCMA_CORE_PCI_SPROM(BCMA_CORE_PCI_SPROM_MISC_CONFIG);
+
+	val16 = pcicore_read16(pc, regoff);
+
+	if (!(val16 & BCMA_CORE_PCI_SPROM_L23READY_EXIT_NOPERST)) {
+		val16 |= BCMA_CORE_PCI_SPROM_L23READY_EXIT_NOPERST;
+		pcicore_write16(pc, regoff, val16);
+	}
+}
+
 /**************************************************
  * Init.
  **************************************************/
 
 static void __devinit bcma_core_pci_clientmode_init(struct bcma_drv_pci *pc)
 {
+	bcma_core_pci_fixcfg(pc);
 	bcma_pcicore_serdes_workaround(pc);
+	bcma_core_pci_config_fixup(pc);
 }
 
 void __devinit bcma_core_pci_init(struct bcma_drv_pci *pc)
@@ -224,3 +259,17 @@ int bcma_core_pci_irq_ctl(struct bcma_drv_pci *pc, struct bcma_device *core,
 	return err;
 }
 EXPORT_SYMBOL_GPL(bcma_core_pci_irq_ctl);
+
+void bcma_core_pci_extend_L1timer(struct bcma_drv_pci *pc, bool extend)
+{
+	u32 w;
+
+	w = bcma_pcie_read(pc, BCMA_CORE_PCI_DLLP_PMTHRESHREG);
+	if (extend)
+		w |= BCMA_CORE_PCI_ASPMTIMER_EXTEND;
+	else
+		w &= ~BCMA_CORE_PCI_ASPMTIMER_EXTEND;
+	bcma_pcie_write(pc, BCMA_CORE_PCI_DLLP_PMTHRESHREG, w);
+	bcma_pcie_read(pc, BCMA_CORE_PCI_DLLP_PMTHRESHREG);
+}
+EXPORT_SYMBOL_GPL(bcma_core_pci_extend_L1timer);

drivers/bcma/driver_pci_host.c

@@ -119,7 +119,7 @@ static int bcma_extpci_read_config(struct bcma_drv_pci *pc, unsigned int dev,
 		if (unlikely(!addr))
 			goto out;
 		err = -ENOMEM;
-		mmio = ioremap_nocache(addr, len);
+		mmio = ioremap_nocache(addr, sizeof(val));
 		if (!mmio)
 			goto out;
 
@@ -171,7 +171,7 @@ static int bcma_extpci_write_config(struct bcma_drv_pci *pc, unsigned int dev,
 			addr = pc->core->addr + BCMA_CORE_PCI_PCICFG0;
 			addr |= (func << 8);
 			addr |= (off & 0xfc);
-			mmio = ioremap_nocache(addr, len);
+			mmio = ioremap_nocache(addr, sizeof(val));
 			if (!mmio)
 				goto out;
 		}
@@ -180,7 +180,7 @@ static int bcma_extpci_write_config(struct bcma_drv_pci *pc, unsigned int dev,
 		if (unlikely(!addr))
 			goto out;
 		err = -ENOMEM;
-		mmio = ioremap_nocache(addr, len);
+		mmio = ioremap_nocache(addr, sizeof(val));
 		if (!mmio)
 			goto out;
 
@@ -491,8 +491,8 @@ void __devinit bcma_core_pci_hostmode_init(struct bcma_drv_pci *pc)
 	/* Ok, ready to run, register it to the system.
 	 * The following needs change, if we want to port hostmode
 	 * to non-MIPS platform. */
-	io_map_base = (unsigned long)ioremap_nocache(BCMA_SOC_PCI_MEM,
-						     0x04000000);
+	io_map_base = (unsigned long)ioremap_nocache(pc_host->mem_resource.start,
+						     resource_size(&pc_host->mem_resource));
 	pc_host->pci_controller.io_map_base = io_map_base;
 	set_io_port_base(pc_host->pci_controller.io_map_base);
 	/* Give some time to the PCI controller to configure itself with the new

drivers/bcma/host_pci.c

@@ -201,6 +201,9 @@ static int __devinit bcma_host_pci_probe(struct pci_dev *dev,
 	bus->hosttype = BCMA_HOSTTYPE_PCI;
 	bus->ops = &bcma_host_pci_ops;
 
+	bus->boardinfo.vendor = bus->host_pci->subsystem_vendor;
+	bus->boardinfo.type = bus->host_pci->subsystem_device;
+
 	/* Register */
 	err = bcma_bus_register(bus);
 	if (err)
@@ -222,7 +225,7 @@ static int __devinit bcma_host_pci_probe(struct pci_dev *dev,
 	return err;
 }
 
-static void bcma_host_pci_remove(struct pci_dev *dev)
+static void __devexit bcma_host_pci_remove(struct pci_dev *dev)
 {
 	struct bcma_bus *bus = pci_get_drvdata(dev);
 
@@ -277,7 +280,7 @@ static struct pci_driver bcma_pci_bridge_driver = {
 	.name = "bcma-pci-bridge",
 	.id_table = bcma_pci_bridge_tbl,
 	.probe = bcma_host_pci_probe,
-	.remove = bcma_host_pci_remove,
+	.remove = __devexit_p(bcma_host_pci_remove),
 	.driver.pm = BCMA_PM_OPS,
 };