Merge tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/ke…

…rnel/git/helgaas/pci

Pull PCI updates from Bjorn Helgaas:
 "Enumeration:

   - Warn if a host bridge has no NUMA info (Yunsheng Lin)

   - Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
     Efremov)

  Resource management:

   - Fix boot-time Embedded Controller GPE storm caused by incorrect
     resource assignment after ACPI Bus Check Notification (Mika
     Westerberg)

   - Protect pci_reassign_bridge_resources() against concurrent
     addition/removal (Benjamin Herrenschmidt)

   - Fix bridge dma_ranges resource list cleanup (Rob Herring)

   - Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
     the MMIO and prefetchable MMIO window sizes of hotplug bridges
     independently (Nicholas Johnson)

   - Fix MMIO/MMIO_PREF window assignment that assigned more space than
     desired (Nicholas Johnson)

   - Only enforce bus numbers from bridge EA if the bridge has EA
     devices downstream (Subbaraya Sundeep)

   - Consolidate DT "dma-ranges" parsing and convert all host drivers to
     use shared parsing (Rob Herring)

  Error reporting:

   - Restore AER capability after resume (Mayurkumar Patel)

   - Add PoisonTLPBlocked AER counter (Rajat Jain)

   - Use for_each_set_bit() to simplify AER code (Andy Shevchenko)

   - Fix AER kernel-doc (Andy Shevchenko)

   - Add "pcie_ports=dpc-native" parameter to allow native use of DPC
     even if platform didn't grant control over AER (Olof Johansson)

  Hotplug:

   - Avoid returning prematurely from sysfs requests to enable or
     disable a PCIe hotplug slot (Lukas Wunner)

   - Don't disable interrupts twice when suspending hotplug ports (Mika
     Westerberg)

   - Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
     Westerberg)

  Power management:

   - Remove unnecessary ASPM locking (Bjorn Helgaas)

   - Add support for disabling L1 PM Substates (Heiner Kallweit)

   - Allow re-enabling Clock PM after it has been disabled (Heiner
     Kallweit)

   - Add sysfs attributes for controlling ASPM link states (Heiner
     Kallweit)

   - Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
     sysfs files (Heiner Kallweit)

   - Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
     USB 2.0 or 1.1 connect events (Kai-Heng Feng)

   - Move power state check out of pci_msi_supported() (Bjorn Helgaas)

   - Fix incorrect MSI-X masking on resume and revert related nvme quirk
     for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)

   - Always return devices to D0 when thawing to fix hibernation with
     drivers like mlx4 that used legacy power management (previously we
     only did it for drivers with new power management ops) (Dexuan Cui)

   - Clear PCIe PME Status even for legacy power management (Bjorn
     Helgaas)

   - Fix PCI PM documentation errors (Bjorn Helgaas)

   - Use dev_printk() for more power management messages (Bjorn Helgaas)

   - Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)

   - Convert xen-platform from legacy to generic power management (Bjorn
     Helgaas)

   - Removed unused .resume_early() and .suspend_late() legacy power
     management hooks (Bjorn Helgaas)

   - Rearrange power management code for clarity (Rafael J. Wysocki)

   - Decode power states more clearly ("4" or "D4" really refers to
     "D3cold") (Bjorn Helgaas)

   - Notice when reading PM Control register returns an error (~0)
     instead of interpreting it as being in D3hot (Bjorn Helgaas)

   - Add missing link delays required by the PCIe spec (Mika Westerberg)

  Virtualization:

   - Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
     Helgaas)

   - Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
     previously didn't recognize that) (Kuppuswamy Sathyanarayanan)

   - Allow VFs to use PASID (the PF PASID capability is shared by the
     VFs, but the code previously didn't recognize that) (Kuppuswamy
     Sathyanarayanan)

   - Disconnect PF and VF ATS enablement, since ATS in PFs and
     associated VFs can be enabled independently (Kuppuswamy
     Sathyanarayanan)

   - Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)

   - Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)

   - Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
     Wilczynski)

   - Remove unused PRI and PASID stubs (Bjorn Helgaas)

   - Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
     interfaces that are only used by built-in IOMMU drivers (Bjorn
     Helgaas)

   - Hide PRI and PASID state restoration functions used only inside the
     PCI core (Bjorn Helgaas)

   - Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)

   - Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)

   - Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
     Cherian)

   - Fix the UPDCR register address in the Intel ACS quirk (Steffen
     Liebergeld)

   - Unify ACS quirk implementations (Bjorn Helgaas)

  Amlogic Meson host bridge driver:

   - Fix meson PERST# GPIO polarity problem (Remi Pommarel)

   - Add DT bindings for Amlogic Meson G12A (Neil Armstrong)

   - Fix meson clock names to match DT bindings (Neil Armstrong)

   - Add meson support for Amlogic G12A SoC with separate shared PHY
     (Neil Armstrong)

   - Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
     combo PHY (Neil Armstrong)

   - Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)

   - Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
     (Neil Armstrong)

  Broadcom iProc host bridge driver:

   - Invalidate iProc PAXB address mapping before programming it
     (Abhishek Shah)

   - Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)

  Cadence host bridge driver:

   - Refactor Cadence PCIe host controller to use as a library for both
     host and endpoint (Tom Joseph)

  Freescale Layerscape host bridge driver:

   - Add layerscape LS1028a support (Xiaowei Bao)

  Intel VMD host bridge driver:

   - Add VMD bus 224-255 restriction decode (Jon Derrick)

   - Add VMD 8086:9A0B device ID (Jon Derrick)

   - Remove Keith from VMD maintainer list (Keith Busch)

  Marvell ARMADA 3700 / Aardvark host bridge driver:

   - Use LTSSM state to build link training flag since Aardvark doesn't
     implement the Link Training bit (Remi Pommarel)

   - Delay before training Aardvark link in case PERST# was asserted
     before the driver probe (Remi Pommarel)

   - Fix Aardvark issues with Root Control reads and writes (Remi
     Pommarel)

   - Don't rely on jiffies in Aardvark config access path since
     interrupts may be disabled (Remi Pommarel)

   - Fix Aardvark big-endian support (Grzegorz Jaszczyk)

  Marvell ARMADA 370 / XP host bridge driver:

   - Make mvebu_pci_bridge_emul_ops static (Ben Dooks)

  Microsoft Hyper-V host bridge driver:

   - Add hibernation support for Hyper-V virtual PCI devices (Dexuan
     Cui)

   - Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
     Cui)

   - Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)

  Mobiveil host bridge driver:

   - Change mobiveil csr_read()/write() function names that conflict
     with riscv arch functions (Kefeng Wang)

  NVIDIA Tegra host bridge driver:

   - Fix Tegra CLKREQ dependency programming (Vidya Sagar)

  Renesas R-Car host bridge driver:

   - Remove unnecessary header include from rcar (Andrew Murray)

   - Tighten register index checking for rcar inbound range programming
     (Marek Vasut)

   - Fix rcar inbound range alignment calculation to improve packing of
     multiple entries (Marek Vasut)

   - Update rcar MACCTLR setting to match documentation (Yoshihiro
     Shimoda)

   - Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
     (Yoshihiro Shimoda)

   - Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
     Horman)

  Rockchip host bridge driver:

   - Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
     Murphy)

  Socionext UniPhier host bridge driver:

   - Set uniphier to host (RC) mode always (Kunihiko Hayashi)

  Endpoint drivers:

   - Fix endpoint driver sign extension problem when shifting page
     number to phys_addr_t (Alan Mikhak)

  Misc:

   - Add NumaChip SPDX header (Krzysztof Wilczynski)

   - Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)

   - Remove unused includes (Krzysztof Wilczynski)

   - Removed unused sysfs attribute groups (Ben Dooks)

   - Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)

   - Add PCIe Link Control 2 register field definitions to replace magic
     numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)

   - Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
     Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)

   - Use pcie_capability_read_word() instead of pci_read_config_word()
     in AMDGPU and Radeon CIK/SI (Frederick Lawler)

   - Remove unused pci_irq_get_node() Greg Kroah-Hartman)

   - Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
     (Palmer Dabbelt, Michal Simek)

   - Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)

   - Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
     Helgaas)

   - Fix bridge emulation big-endian support (Grzegorz Jaszczyk)

   - Fix dwc find_next_bit() usage (Niklas Cassel)

   - Fix pcitest.c fd leak (Hewenliang)

   - Fix typos and comments (Bjorn Helgaas)

   - Fix Kconfig whitespace errors (Krzysztof Kozlowski)"

* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
  PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
  asm-generic: Make msi.h a mandatory include/asm header
  Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
  PCI/MSI: Fix incorrect MSI-X masking on resume
  PCI/MSI: Move power state check out of pci_msi_supported()
  PCI/MSI: Remove unused pci_irq_get_node()
  PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
  PCI: hv: Change pci_protocol_version to per-hbus
  PCI: hv: Add hibernation support
  PCI: hv: Reorganize the code in preparation of hibernation
  MAINTAINERS: Remove Keith from VMD maintainer
  PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
  PCI/ASPM: Add sysfs attributes for controlling ASPM link states
  PCI: Fix indentation
  drm/radeon: Prefer pcie_capability_read_word()
  drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
  drm/radeon: Correct Transmit Margin masks
  drm/amdgpu: Prefer pcie_capability_read_word()
  PCI: uniphier: Set mode register to host mode
  drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
  ...

Documentation/ABI/testing/sysfs-bus-pci

@@ -347,3 +347,16 @@ Description:
 		If the device has any Peer-to-Peer memory registered, this
 	        file contains a '1' if the memory has been published for
 		use outside the driver that owns the device.
+
+What:		/sys/bus/pci/devices/.../link/clkpm
+		/sys/bus/pci/devices/.../link/l0s_aspm
+		/sys/bus/pci/devices/.../link/l1_aspm
+		/sys/bus/pci/devices/.../link/l1_1_aspm
+		/sys/bus/pci/devices/.../link/l1_2_aspm
+		/sys/bus/pci/devices/.../link/l1_1_pcipm
+		/sys/bus/pci/devices/.../link/l1_2_pcipm
+Date:		October 2019
+Contact:	Heiner Kallweit <[email protected]>
+Description:	If ASPM is supported for an endpoint, these files can be
+		used to disable or enable the individual power management
+		states. Write y/1/on to enable, n/0/off to disable.

Documentation/admin-guide/kernel-parameters.txt

@@ -3540,8 +3540,15 @@
 		hpiosize=nn[KMG]	The fixed amount of bus space which is
 				reserved for hotplug bridge's IO window.
 				Default size is 256 bytes.
+		hpmmiosize=nn[KMG]	The fixed amount of bus space which is
+				reserved for hotplug bridge's MMIO window.
+				Default size is 2 megabytes.
+		hpmmioprefsize=nn[KMG]	The fixed amount of bus space which is
+				reserved for hotplug bridge's MMIO_PREF window.
+				Default size is 2 megabytes.
 		hpmemsize=nn[KMG]	The fixed amount of bus space which is
-				reserved for hotplug bridge's memory window.
+				reserved for hotplug bridge's MMIO and
+				MMIO_PREF window.
 				Default size is 2 megabytes.
 		hpbussize=nn	The minimum amount of additional bus numbers
 				reserved for buses below a hotplug bridge.
@@ -3588,6 +3595,8 @@
 			even if the platform doesn't give the OS permission to
 			use them.  This may cause conflicts if the platform
 			also tries to use these services.
+		dpc-native	Use native PCIe service for DPC only.  May
+				cause conflicts if firmware uses AER or DPC.
 		compat	Disable native PCIe services (PME, AER, DPC, PCIe
 			hotplug).
 

Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt

@@ -9,26 +9,30 @@ Additional properties are described here:
 
 Required properties:
 - compatible:
-	should contain "amlogic,axg-pcie" to identify the core.
+	should contain :
+	- "amlogic,axg-pcie" for AXG SoC Family
+	- "amlogic,g12a-pcie" for G12A SoC Family
+	to identify the core.
 - reg:
 	should contain the configuration address space.
 - reg-names: Must be
 	- "elbi"	External local bus interface registers
 	- "cfg"		Meson specific registers
-	- "phy"		Meson PCIE PHY registers
+	- "phy"		Meson PCIE PHY registers for AXG SoC Family
 	- "config"	PCIe configuration space
 - reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal.
 - clocks: Must contain an entry for each entry in clock-names.
 - clock-names: Must include the following entries:
 	- "pclk"       PCIe GEN 100M PLL clock
 	- "port"       PCIe_x(A or B) RC clock gate
 	- "general"    PCIe Phy clock
-	- "mipi"       PCIe_x(A or B) 100M ref clock gate
+	- "mipi"       PCIe_x(A or B) 100M ref clock gate for AXG SoC Family
 - resets: phandle to the reset lines.
 - reset-names: must contain "phy" "port" and "apb"
-       - "phy"         Share PHY reset
+       - "phy"         Share PHY reset for AXG SoC Family
        - "port"        Port A or B reset
        - "apb"         Share APB reset
+- phys: should contain a phandle to the shared phy for G12A SoC Family
 - device_type:
 	should be "pci". As specified in designware-pcie.txt
 

Documentation/devicetree/bindings/pci/layerscape-pci.txt

@@ -21,6 +21,7 @@ Required properties:
         "fsl,ls1046a-pcie"
         "fsl,ls1043a-pcie"
         "fsl,ls1012a-pcie"
+        "fsl,ls1028a-pcie"
   EP mode:
 	"fsl,ls1046a-pcie-ep", "fsl,ls-pcie-ep"
 - reg: base addresses and lengths of the PCIe controller register blocks.

Documentation/power/pci.rst

@@ -130,8 +130,8 @@ a full power-on reset sequence and the power-on defaults are restored to the
 device by hardware just as at initial power up.
 
 PCI devices supporting the PCI PM Spec can be programmed to generate PMEs
-while in a low-power state (D1-D3), but they are not required to be capable
-of generating PMEs from all supported low-power states.  In particular, the
+while in any power state (D0-D3), but they are not required to be capable
+of generating PMEs from all supported power states.  In particular, the
 capability of generating PMEs from D3cold is optional and depends on the
 presence of additional voltage (3.3Vaux) allowing the device to remain
 sufficiently active to generate a wakeup signal.
@@ -600,17 +600,17 @@ using the following PCI bus type's callbacks::
 
 respectively.
 
-The first of them, pci_pm_thaw_noirq(), is analogous to pci_pm_resume_noirq(),
-but it doesn't put the device into the full power state and doesn't attempt to
-restore its standard configuration registers.  It also executes the device
-driver's pm->thaw_noirq() callback, if defined, instead of pm->resume_noirq().
+The first of them, pci_pm_thaw_noirq(), is analogous to pci_pm_resume_noirq().
+It puts the device into the full power state and restores its standard
+configuration registers.  It also executes the device driver's pm->thaw_noirq()
+callback, if defined, instead of pm->resume_noirq().
 
 The pci_pm_thaw() routine is similar to pci_pm_resume(), but it runs the device
 driver's pm->thaw() callback instead of pm->resume().  It is executed
 asynchronously for different PCI devices that don't depend on each other in a
 known way.
 
-The complete phase it the same as for system resume.
+The complete phase is the same as for system resume.
 
 After saving the image, devices need to be powered down before the system can
 enter the target sleep state (ACPI S4 for ACPI-based systems).  This is done in
@@ -692,11 +692,11 @@ controlling the runtime power management of their devices.
 At the time of this writing there are two ways to define power management
 callbacks for a PCI device driver, the recommended one, based on using a
 dev_pm_ops structure described in Documentation/driver-api/pm/devices.rst, and
-the "legacy" one, in which the .suspend(), .suspend_late(), .resume_early(), and
-.resume() callbacks from struct pci_driver are used.  The legacy approach,
-however, doesn't allow one to define runtime power management callbacks and is
-not really suitable for any new drivers.  Therefore it is not covered by this
-document (refer to the source code to learn more about it).
+the "legacy" one, in which the .suspend() and .resume() callbacks from struct
+pci_driver are used.  The legacy approach, however, doesn't allow one to define
+runtime power management callbacks and is not really suitable for any new
+drivers.  Therefore it is not covered by this document (refer to the source code
+to learn more about it).
 
 It is recommended that all PCI device drivers define a struct dev_pm_ops object
 containing pointers to power management (PM) callbacks that will be executed by

MAINTAINERS

@@ -12600,7 +12600,6 @@ F:	Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
 F:	drivers/pci/controller/dwc/*imx6*
 
 PCI DRIVER FOR INTEL VOLUME MANAGEMENT DEVICE (VMD)
-M:	Keith Busch <[email protected]>
 M:	Jonathan Derrick <[email protected]>
 L:	[email protected]
 S:	Supported
@@ -12643,7 +12642,8 @@ F:	Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt
 F:	drivers/pci/controller/pci-tegra.c
 
 PCI DRIVER FOR RENESAS R-CAR
-M:	Simon Horman <[email protected]>
+M:	Marek Vasut <[email protected]>
+M:	Yoshihiro Shimoda <[email protected]>
 L:	[email protected]
 L:	[email protected]
 S:	Maintained

arch/alpha/kernel/pci-sysfs.c

@@ -71,10 +71,10 @@ static int pci_mmap_resource(struct kobject *kobj,
 	struct pci_bus_region bar;
 	int i;
 
-	for (i = 0; i < PCI_ROM_RESOURCE; i++)
+	for (i = 0; i < PCI_STD_NUM_BARS; i++)
 		if (res == &pdev->resource[i])
 			break;
-	if (i >= PCI_ROM_RESOURCE)
+	if (i >= PCI_STD_NUM_BARS)
 		return -ENODEV;
 
 	if (res->flags & IORESOURCE_MEM && iomem_is_exclusive(res->start))
@@ -115,7 +115,7 @@ void pci_remove_resource_files(struct pci_dev *pdev)
 {
 	int i;
 
-	for (i = 0; i < PCI_ROM_RESOURCE; i++) {
+	for (i = 0; i < PCI_STD_NUM_BARS; i++) {
 		struct bin_attribute *res_attr;
 
 		res_attr = pdev->res_attr[i];
@@ -232,7 +232,7 @@ int pci_create_resource_files(struct pci_dev *pdev)
 	int retval;
 
 	/* Expose the PCI resources from this device as files */
-	for (i = 0; i < PCI_ROM_RESOURCE; i++) {
+	for (i = 0; i < PCI_STD_NUM_BARS; i++) {
 
 		/* skip empty resources */
 		if (!pci_resource_len(pdev, i))

arch/arc/include/asm/Kbuild

@@ -17,7 +17,6 @@ generic-y += local64.h
 generic-y += mcs_spinlock.h
 generic-y += mm-arch-hooks.h
 generic-y += mmiowb.h
-generic-y += msi.h
 generic-y += parport.h
 generic-y += percpu.h
 generic-y += preempt.h

arch/arm/include/asm/Kbuild

@@ -12,7 +12,6 @@ generic-y += local.h
 generic-y += local64.h
 generic-y += mm-arch-hooks.h
 generic-y += mmiowb.h
-generic-y += msi.h
 generic-y += parport.h
 generic-y += preempt.h
 generic-y += seccomp.h

arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi

@@ -95,6 +95,39 @@
 		#size-cells = <2>;
 		ranges;
 
+		pcie: pcie@fc000000 {
+			compatible = "amlogic,g12a-pcie", "snps,dw-pcie";
+			reg = <0x0 0xfc000000 0x0 0x400000
+			       0x0 0xff648000 0x0 0x2000
+			       0x0 0xfc400000 0x0 0x200000>;
+			reg-names = "elbi", "cfg", "config";
+			interrupts = <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+			bus-range = <0x0 0xff>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x81000000 0 0 0x0 0xfc600000 0 0x00100000
+				  0x82000000 0 0xfc700000 0x0 0xfc700000 0 0x1900000>;
+
+			clocks = <&clkc CLKID_PCIE_PHY
+				  &clkc CLKID_PCIE_COMB
+				  &clkc CLKID_PCIE_PLL>;
+			clock-names = "general",
+				      "pclk",
+				      "port";
+			resets = <&reset RESET_PCIE_CTRL_A>,
+				 <&reset RESET_PCIE_APB>;
+			reset-names = "port",
+				      "apb";
+			num-lanes = <1>;
+			phys = <&usb3_pcie_phy PHY_TYPE_PCIE>;
+			phy-names = "pcie";
+			status = "disabled";
+		};
+
 		ethmac: ethernet@ff3f0000 {
 			compatible = "amlogic,meson-axg-dwmac",
 				     "snps,dwmac-3.70a",

arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts

@@ -14,3 +14,28 @@
 / {
 	compatible = "khadas,vim3", "amlogic,a311d", "amlogic,g12b";
 };
+
+/*
+ * The VIM3 on-board  MCU can mux the PCIe/USB3.0 shared differential
+ * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
+ * an USB3.0 Type A connector and a M.2 Key M slot.
+ * The PHY driving these differential lines is shared between
+ * the USB3.0 controller and the PCIe Controller, thus only
+ * a single controller can use it.
+ * If the MCU is configured to mux the PCIe/USB3.0 differential lines
+ * to the M.2 Key M slot, uncomment the following block to disable
+ * USB3.0 from the USB Complex and enable the PCIe controller.
+ * The End User is not expected to uncomment the following except for
+ * testing purposes, but instead rely on the firmware/bootloader to
+ * update these nodes accordingly if PCIe mode is selected by the MCU.
+ */
+/*
+&pcie {
+	status = "okay";
+};
+
+&usb {
+	phys = <&usb2_phy0>, <&usb2_phy1>;
+	phy-names = "usb2-phy0", "usb2-phy1";
+};
+ */

arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts

@@ -14,3 +14,28 @@
 / {
 	compatible = "khadas,vim3", "amlogic,s922x", "amlogic,g12b";
 };
+
+/*
+ * The VIM3 on-board  MCU can mux the PCIe/USB3.0 shared differential
+ * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
+ * an USB3.0 Type A connector and a M.2 Key M slot.
+ * The PHY driving these differential lines is shared between
+ * the USB3.0 controller and the PCIe Controller, thus only
+ * a single controller can use it.
+ * If the MCU is configured to mux the PCIe/USB3.0 differential lines
+ * to the M.2 Key M slot, uncomment the following block to disable
+ * USB3.0 from the USB Complex and enable the PCIe controller.
+ * The End User is not expected to uncomment the following except for
+ * testing purposes, but instead rely on the firmware/bootloader to
+ * update these nodes accordingly if PCIe mode is selected by the MCU.
+ */
+/*
+&pcie {
+	status = "okay";
+};
+
+&usb {
+	phys = <&usb2_phy0>, <&usb2_phy1>;
+	phy-names = "usb2-phy0", "usb2-phy1";
+};
+ */

arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi

@@ -246,6 +246,10 @@
 	linux,rc-map-name = "rc-khadas";
 };
 
+&pcie {
+	reset-gpios = <&gpio GPIOA_8 GPIO_ACTIVE_LOW>;
+};
+
 &pwm_ef {
         status = "okay";
         pinctrl-0 = <&pwm_e_pins>;

arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts

@@ -68,3 +68,28 @@
 	clock-names = "clkin1";
 	status = "okay";
 };
+
+/*
+ * The VIM3 on-board  MCU can mux the PCIe/USB3.0 shared differential
+ * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
+ * an USB3.0 Type A connector and a M.2 Key M slot.
+ * The PHY driving these differential lines is shared between
+ * the USB3.0 controller and the PCIe Controller, thus only
+ * a single controller can use it.
+ * If the MCU is configured to mux the PCIe/USB3.0 differential lines
+ * to the M.2 Key M slot, uncomment the following block to disable
+ * USB3.0 from the USB Complex and enable the PCIe controller.
+ * The End User is not expected to uncomment the following except for
+ * testing purposes, but instead rely on the firmware/bootloader to
+ * update these nodes accordingly if PCIe mode is selected by the MCU.
+ */
+/*
+&pcie {
+	status = "okay";
+};
+
+&usb {
+	phys = <&usb2_phy0>, <&usb2_phy1>;
+	phy-names = "usb2-phy0", "usb2-phy1";
+};
+ */

arch/arm64/boot/dts/amlogic/meson-sm1.dtsi

@@ -134,6 +134,10 @@
 	power-domains = <&pwrc PWRC_SM1_ETH_ID>;
 };
 
+&pcie {
+	power-domains = <&pwrc PWRC_SM1_PCIE_ID>;
+};
+
 &pwrc {
 	compatible = "amlogic,meson-sm1-pwrc";
 };

arch/arm64/include/asm/Kbuild

@@ -16,7 +16,6 @@ generic-y += local64.h
 generic-y += mcs_spinlock.h
 generic-y += mm-arch-hooks.h
 generic-y += mmiowb.h
-generic-y += msi.h
 generic-y += qrwlock.h
 generic-y += qspinlock.h
 generic-y += serial.h

arch/mips/include/asm/Kbuild

@@ -13,7 +13,6 @@ generic-y += irq_work.h
 generic-y += local64.h
 generic-y += mcs_spinlock.h
 generic-y += mm-arch-hooks.h
-generic-y += msi.h
 generic-y += parport.h
 generic-y += percpu.h
 generic-y += preempt.h

arch/powerpc/include/asm/Kbuild

@@ -11,5 +11,4 @@ generic-y += local64.h
 generic-y += mcs_spinlock.h
 generic-y += preempt.h
 generic-y += vtime.h
-generic-y += msi.h
 generic-y += early_ioremap.h

arch/riscv/include/asm/Kbuild

@@ -22,7 +22,6 @@ generic-y += kvm_para.h
 generic-y += local.h
 generic-y += local64.h
 generic-y += mm-arch-hooks.h
-generic-y += msi.h
 generic-y += percpu.h
 generic-y += preempt.h
 generic-y += sections.h

arch/s390/include/asm/pci.h

@@ -2,9 +2,6 @@
 #ifndef __ASM_S390_PCI_H
 #define __ASM_S390_PCI_H
 
-/* must be set before including pci_clp.h */
-#define PCI_BAR_COUNT	6
-
 #include <linux/pci.h>
 #include <linux/mutex.h>
 #include <linux/iommu.h>
@@ -138,7 +135,7 @@ struct zpci_dev {
 
 	char res_name[16];
 	bool mio_capable;
-	struct zpci_bar_struct bars[PCI_BAR_COUNT];
+	struct zpci_bar_struct bars[PCI_STD_NUM_BARS];
 
 	u64		start_dma;	/* Start of available DMA addresses */
 	u64		end_dma;	/* End of available DMA addresses */