Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/…

…davem/net-2.6 Conflicts: drivers/net/tokenring/tmspci.c drivers/net/ucc_geth_mii.c
kyagi · Mar 5, 2009 · 508827f · 508827f
2 parents 2c3c3d0 + 72e2240
commit 508827f
Show file tree

Hide file tree

Showing 120 changed files with 1,050 additions and 543 deletions.
diff --git a/Documentation/networking/ipv6.txt b/Documentation/networking/ipv6.txt
@@ -0,0 +1,35 @@
+
+Options for the ipv6 module are supplied as parameters at load time.
+
+Module options may be given as command line arguments to the insmod
+or modprobe command, but are usually specified in either the
+/etc/modules.conf or /etc/modprobe.conf configuration file, or in a
+distro-specific configuration file.
+
+The available ipv6 module parameters are listed below.  If a parameter
+is not specified the default value is used.
+
+The parameters are as follows:
+
+disable
+
+	Specifies whether to load the IPv6 module, but disable all
+	its functionality.  This might be used when another module
+	has a dependency on the IPv6 module being loaded, but no
+	IPv6 addresses or operations are desired.
+
+	The possible values and their effects are:
+
+	0
+		IPv6 is enabled.
+
+		This is the default value.
+
+	1
+		IPv6 is disabled.
+
+		No IPv6 addresses will be added to interfaces, and
+		it will not be possible to open an IPv6 socket.
+
+		A reboot is required to enable IPv6.
+
diff --git a/Documentation/scsi/cxgb3i.txt b/Documentation/scsi/cxgb3i.txt
@@ -4,7 +4,7 @@ Introduction
 ============
 
 The Chelsio T3 ASIC based Adapters (S310, S320, S302, S304, Mezz cards, etc.
-series of products) supports iSCSI acceleration and iSCSI Direct Data Placement
+series of products) support iSCSI acceleration and iSCSI Direct Data Placement
 (DDP) where the hardware handles the expensive byte touching operations, such
 as CRC computation and verification, and direct DMA to the final host memory
 destination:
@@ -31,9 +31,9 @@ destination:
 	  the TCP segments onto the wire. It handles TCP retransmission if
 	  needed.
 
-	  On receving, S3 h/w recovers the iSCSI PDU by reassembling TCP
+	  On receiving, S3 h/w recovers the iSCSI PDU by reassembling TCP
 	  segments, separating the header and data, calculating and verifying
-	  the digests, then forwards the header to the host. The payload data,
+	  the digests, then forwarding the header to the host. The payload data,
 	  if possible, will be directly placed into the pre-posted host DDP
 	  buffer. Otherwise, the payload data will be sent to the host too.
 
@@ -68,9 +68,8 @@ The following steps need to be taken to accelerates the open-iscsi initiator:
 	sure the ip address is unique in the network.
 
 3. edit /etc/iscsi/iscsid.conf
-   The default setting for MaxRecvDataSegmentLength (131072) is too big,
-   replace "node.conn[0].iscsi.MaxRecvDataSegmentLength" to be a value no
-   bigger than 15360 (for example 8192):
+   The default setting for MaxRecvDataSegmentLength (131072) is too big;
+   replace with a value no bigger than 15360 (for example 8192):
 
 	node.conn[0].iscsi.MaxRecvDataSegmentLength = 8192
 

diff --git a/MAINTAINERS b/MAINTAINERS
@@ -2466,7 +2466,7 @@ S:	Maintained
 
 ISDN SUBSYSTEM
 P:	Karsten Keil
-M:	kkeil@suse.de
+M:	isdn@linux-pingi.de
 L:	[email protected] (subscribers-only)
 W:	http://www.isdn4linux.de
 T:	git kernel.org:/pub/scm/linux/kernel/kkeil/isdn-2.6.git

diff --git a/Makefile b/Makefile
@@ -1,7 +1,7 @@
 VERSION = 2
 PATCHLEVEL = 6
 SUBLEVEL = 29
-EXTRAVERSION = -rc6
+EXTRAVERSION = -rc7
 NAME = Erotic Pickled Herring
 
 # *DOCUMENTATION*

diff --git a/arch/arm/kernel/setup.c b/arch/arm/kernel/setup.c
@@ -233,12 +233,13 @@ static void __init cacheid_init(void)
 	unsigned int cachetype = read_cpuid_cachetype();
 	unsigned int arch = cpu_architecture();
 
-	if (arch >= CPU_ARCH_ARMv7) {
-		cacheid = CACHEID_VIPT_NONALIASING;
-		if ((cachetype & (3 << 14)) == 1 << 14)
-			cacheid |= CACHEID_ASID_TAGGED;
-	} else if (arch >= CPU_ARCH_ARMv6) {
-		if (cachetype & (1 << 23))
+	if (arch >= CPU_ARCH_ARMv6) {
+		if ((cachetype & (7 << 29)) == 4 << 29) {
+			/* ARMv7 register format */
+			cacheid = CACHEID_VIPT_NONALIASING;
+			if ((cachetype & (3 << 14)) == 1 << 14)
+				cacheid |= CACHEID_ASID_TAGGED;
+		} else if (cachetype & (1 << 23))
 			cacheid = CACHEID_VIPT_ALIASING;
 		else
 			cacheid = CACHEID_VIPT_NONALIASING;

diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
@@ -332,7 +332,6 @@ static int at91_pm_enter(suspend_state_t state)
 			at91_sys_read(AT91_AIC_IPR) & at91_sys_read(AT91_AIC_IMR));
 
 error:
-	sdram_selfrefresh_disable();
 	target_state = PM_SUSPEND_ON;
 	at91_irq_resume();
 	at91_gpio_resume();

diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c
@@ -81,7 +81,7 @@ static inline void __init ldp_init_smc911x(void)
 	}
 
 	ldp_smc911x_resources[0].start = cs_mem_base + 0x0;
-	ldp_smc911x_resources[0].end   = cs_mem_base + 0xf;
+	ldp_smc911x_resources[0].end   = cs_mem_base + 0xff;
 	udelay(100);
 
 	eth_gpio = LDP_SMC911X_GPIO;

diff --git a/arch/arm/mm/abort-ev6.S b/arch/arm/mm/abort-ev6.S
@@ -23,7 +23,8 @@ ENTRY(v6_early_abort)
 #ifdef CONFIG_CPU_32v6K
 	clrex
 #else
-	strex	r0, r1, [sp]			@ Clear the exclusive monitor
+	sub	r1, sp, #4			@ Get unused stack location
+	strex	r0, r1, [r1]			@ Clear the exclusive monitor
 #endif
 	mrc	p15, 0, r1, c5, c0, 0		@ get FSR
 	mrc	p15, 0, r0, c6, c0, 0		@ get FAR

diff --git a/arch/arm/plat-s3c64xx/irq-eint.c b/arch/arm/plat-s3c64xx/irq-eint.c
@@ -55,7 +55,7 @@ static void s3c_irq_eint_unmask(unsigned int irq)
 	u32 mask;
 
 	mask = __raw_readl(S3C64XX_EINT0MASK);
-	mask |= eint_irq_to_bit(irq);
+	mask &= ~eint_irq_to_bit(irq);
 	__raw_writel(mask, S3C64XX_EINT0MASK);
 }
 

diff --git a/arch/mips/include/asm/seccomp.h b/arch/mips/include/asm/seccomp.h
@@ -1,6 +1,5 @@
 #ifndef __ASM_SECCOMP_H
 
-#include <linux/thread_info.h>
 #include <linux/unistd.h>
 
 #define __NR_seccomp_read __NR_read

diff --git a/arch/powerpc/include/asm/compat.h b/arch/powerpc/include/asm/compat.h
@@ -210,5 +210,10 @@ struct compat_shmid64_ds {
 	compat_ulong_t __unused6;
 };
 
+static inline int is_compat_task(void)
+{
+	return test_thread_flag(TIF_32BIT);
+}
+
 #endif /* __KERNEL__ */
 #endif /* _ASM_POWERPC_COMPAT_H */
diff --git a/arch/powerpc/include/asm/seccomp.h b/arch/powerpc/include/asm/seccomp.h
@@ -1,10 +1,6 @@
 #ifndef _ASM_POWERPC_SECCOMP_H
 #define _ASM_POWERPC_SECCOMP_H
 
-#ifdef __KERNEL__
-#include <linux/thread_info.h>
-#endif
-
 #include <linux/unistd.h>
 
 #define __NR_seccomp_read __NR_read

diff --git a/arch/powerpc/platforms/86xx/gef_sbc610.c b/arch/powerpc/platforms/86xx/gef_sbc610.c
@@ -142,6 +142,10 @@ static void __init gef_sbc610_nec_fixup(struct pci_dev *pdev)
 {
 	unsigned int val;
 
+	/* Do not do the fixup on other platforms! */
+	if (!machine_is(gef_sbc610))
+		return;
+
 	printk(KERN_INFO "Running NEC uPD720101 Fixup\n");
 
 	/* Ensure ports 1, 2, 3, 4 & 5 are enabled */

diff --git a/arch/s390/crypto/aes_s390.c b/arch/s390/crypto/aes_s390.c
@@ -556,7 +556,7 @@ static void __exit aes_s390_fini(void)
 module_init(aes_s390_init);
 module_exit(aes_s390_fini);
 
-MODULE_ALIAS("aes");
+MODULE_ALIAS("aes-all");
 
 MODULE_DESCRIPTION("Rijndael (AES) Cipher Algorithm");
 MODULE_LICENSE("GPL");
diff --git a/arch/sparc/include/asm/compat.h b/arch/sparc/include/asm/compat.h
@@ -240,4 +240,9 @@ struct compat_shmid64_ds {
 	unsigned int	__unused2;
 };
 
+static inline int is_compat_task(void)
+{
+	return test_thread_flag(TIF_32BIT);
+}
+
 #endif /* _ASM_SPARC64_COMPAT_H */
diff --git a/arch/sparc/include/asm/seccomp.h b/arch/sparc/include/asm/seccomp.h
@@ -1,11 +1,5 @@
 #ifndef _ASM_SECCOMP_H
 
-#include <linux/thread_info.h> /* already defines TIF_32BIT */
-
-#ifndef TIF_32BIT
-#error "unexpected TIF_32BIT on sparc64"
-#endif
-
 #include <linux/unistd.h>
 
 #define __NR_seccomp_read __NR_read

diff --git a/arch/x86/include/asm/seccomp_32.h b/arch/x86/include/asm/seccomp_32.h
@@ -1,12 +1,6 @@
 #ifndef _ASM_X86_SECCOMP_32_H
 #define _ASM_X86_SECCOMP_32_H
 
-#include <linux/thread_info.h>
-
-#ifdef TIF_32BIT
-#error "unexpected TIF_32BIT on i386"
-#endif
-
 #include <linux/unistd.h>
 
 #define __NR_seccomp_read __NR_read

diff --git a/arch/x86/include/asm/seccomp_64.h b/arch/x86/include/asm/seccomp_64.h
@@ -1,14 +1,6 @@
 #ifndef _ASM_X86_SECCOMP_64_H
 #define _ASM_X86_SECCOMP_64_H
 
-#include <linux/thread_info.h>
-
-#ifdef TIF_32BIT
-#error "unexpected TIF_32BIT on x86_64"
-#else
-#define TIF_32BIT TIF_IA32
-#endif
-
 #include <linux/unistd.h>
 #include <asm/ia32_unistd.h>
 

diff --git a/arch/x86/kernel/ptrace.c b/arch/x86/kernel/ptrace.c
@@ -1388,7 +1388,7 @@ void send_sigtrap(struct task_struct *tsk, struct pt_regs *regs,
 #ifdef CONFIG_X86_32
 # define IS_IA32	1
 #elif defined CONFIG_IA32_EMULATION
-# define IS_IA32	test_thread_flag(TIF_IA32)
+# define IS_IA32	is_compat_task()
 #else
 # define IS_IA32	0
 #endif

diff --git a/arch/x86/mm/init_64.c b/arch/x86/mm/init_64.c
@@ -714,6 +714,8 @@ unsigned long __init_refok init_memory_mapping(unsigned long start,
 	pos = start_pfn << PAGE_SHIFT;
 	end_pfn = ((pos + (PMD_SIZE - 1)) >> PMD_SHIFT)
 			<< (PMD_SHIFT - PAGE_SHIFT);
+	if (end_pfn > (end >> PAGE_SHIFT))
+		end_pfn = end >> PAGE_SHIFT;
 	if (start_pfn < end_pfn) {
 		nr_range = save_mr(mr, nr_range, start_pfn, end_pfn, 0);
 		pos = end_pfn << PAGE_SHIFT;

diff --git a/arch/x86/mm/iomap_32.c b/arch/x86/mm/iomap_32.c
@@ -20,23 +20,16 @@
 #include <asm/pat.h>
 #include <linux/module.h>
 
-#ifdef CONFIG_X86_PAE
-int
-is_io_mapping_possible(resource_size_t base, unsigned long size)
-{
-	return 1;
-}
-#else
-int
-is_io_mapping_possible(resource_size_t base, unsigned long size)
+int is_io_mapping_possible(resource_size_t base, unsigned long size)
 {
+#ifndef CONFIG_X86_PAE
 	/* There is no way to map greater than 1 << 32 address without PAE */
 	if (base + size > 0x100000000ULL)
 		return 0;
-
+#endif
 	return 1;
 }
-#endif
+EXPORT_SYMBOL_GPL(is_io_mapping_possible);
 
 /* Map 'pfn' using fixed map 'type' and protections 'prot'
  */