An example Rust project that uses pin GPIO15 on an XIAO-ESP32-C6 board to blink an BUILTIN LED.
Project was generated using esp-teamplate:
cargo generate -a https://github.com/esp-rs/esp-template
⚠️ Favorite `https://github.com/esp-rs/esp-template` not found in config, using it as a git repository: https://github.com/esp-rs/esp-template
🤷 Project Name: xiao-esp32c6-blinky
🔧 Destination: /Users/mordor/Src/rust/rust-embedded/xiao-esp32c6-blinky ...
🔧 project-name: xiao-esp32c6-blinky ...
🔧 Generating template ...
✔ 🤷 Which MCU to target? · esp32c6
✔ 🤷 Configure advanced template options? · false
🔧 Moving generated files into: `/Users/mordor/Src/rust/rust-embedded/xiao-esp32c6-blinky`...
🔧 Initializing a fresh Git repository
✨ Done! New project created ~/Src/rust/rust-embedded/xiao-esp32c6-blinkyTo build run this command:
cargo build --releaseTo flash this project, run this command:
cargo run --release
Compiling xiao-esp32c6-blinky v0.1.0 (/Users/mordor/Src/rust/rust-embedded/xiao-esp32c6-blinky)
Finished `release` profile [optimized + debuginfo] target(s) in 58.42s
Running `espflash flash --monitor target/riscv32imac-unknown-none-elf/release/xiao-esp32c6-blinky`
[2024-10-31T00:22:53Z INFO ] Detected 2 serial ports
[2024-10-31T00:22:53Z INFO ] Ports which match a known common dev board are highlighted
[2024-10-31T00:22:53Z INFO ] Please select a port
[2024-10-31T00:23:31Z INFO ] Serial port: '/dev/cu.usbmodem1417401'
[2024-10-31T00:23:31Z INFO ] Connecting...
[2024-10-31T00:23:31Z INFO ] Using flash stub
Chip type: esp32c6 (revision v0.1)
Crystal frequency: 40 MHz
Flash size: 4MB
Features: WiFi 6, BT 5
MAC address: f0:f5:bd:2d:0c:88
App/part. size: 21,040/4,128,768 bytes, 0.51%
[00:00:00] [========================================] 13/13 0x0 [00:00:00] [========================================] 1/1 0x8000 [00:00:00] [========================================] 13/13 0x10000 [2024-10-31T00:23:32Z INFO ] Flashing has completed!
Commands:
CTRL+R Reset chip
CTRL+C Exit
ESP-ROM:esp32c6-20220919
Build:Sep 19 2022
rst:0x15 (USB_UART_HPSYS),boot:0x16 (DOWNLOAD(USB/UART0/SDIO_REI_FEO))
Saved PC:0x4080054c
0x4080054c - esp32c6::gpio::RegisterBlock::pin
at /Users/mordor/.cargo/registry/src/index.crates.io-6f17d22bba15001f/esp32c6-0.16.0/src/gpio.rs:195
SPIWP:0xee
mode:DIO, clock div:2
load:0x4086c410,len:0xd48
load:0x4086e610,len:0x2d68
load:0x40875720,len:0x1800
entry 0x4086c410
I (23) boot: ESP-IDF v5.1-beta1-378-gea5e0ff298-dirt 2nd stage bootloader
I (23) boot: compile time Jun 7 2023 08:02:08
I (24) boot: chip revision: v0.1
I (28) boot.esp32c6: SPI Speed : 40MHz
I (33) boot.esp32c6: SPI Mode : DIO
I (37) boot.esp32c6: SPI Flash Size : 4MB
I (42) boot: Enabling RNG early entropy source...
I (48) boot: Partition Table:
I (51) boot: ## Label Usage Type ST Offset Length
I (58) boot: 0 nvs WiFi data 01 02 00009000 00006000
I (66) boot: 1 phy_init RF data 01 01 0000f000 00001000
I (73) boot: 2 factory factory app 00 00 00010000 003f0000
I (81) boot: End of partition table
I (85) esp_image: segment 0: paddr=00010020 vaddr=42000020 size=048dch ( 18652) map
I (97) esp_image: segment 1: paddr=00014904 vaddr=40800000 size=00014h ( 20) load
I (102) esp_image: segment 2: paddr=00014920 vaddr=42004920 size=01fa8h ( 8104) map
I (112) esp_image: segment 3: paddr=000168d0 vaddr=40800014 size=008e4h ( 2276) load
I (120) boot: Loaded app from partition at offset 0x10000
I (125) boot: Disabling RNG early entropy source...You can check board info:
espflash board-info
[2024-10-31T00:29:09Z INFO ] Detected 2 serial ports
[2024-10-31T00:29:09Z INFO ] Ports which match a known common dev board are highlighted
[2024-10-31T00:29:09Z INFO ] Please select a port
[2024-10-31T00:29:12Z INFO ] Serial port: '/dev/cu.usbmodem1417401'
[2024-10-31T00:29:12Z INFO ] Connecting...
[2024-10-31T00:29:13Z INFO ] Using flash stub
Chip type: esp32c6 (revision v0.1)
Crystal frequency: 40 MHz
Flash size: 4MB
Features: WiFi 6, BT 5
MAC address: f0:f5:bd:2d:0c:88