[Keyboard] Add Budget96 by Donut Cables (qmk#5550)

* initial commit of budget96 * non logic changes * add my name to readme * update matrix.c * make the matrix representation of the layout macro * fix up LAYOUT macro * add missing character * initial keymap commit * put KC_NO where they belong * basic keymap * fix matrix row and col definition * The diagram I was sent and the pins used I was sent were in opposite order from each other. This should fix the issues * update the readme * change up manufacturer for budget96 * update copyright date * fix up the switch matrix and provide a keymap * forgot the keymap * other matrix fixes * missing a few keys in the switch matrix * messed up the row tracing * tweak keymap a bit * use a lower case k * fix spacing for markdown rendering * put in the reset key documentation * clean up the file a little * use LAYOUT_96_ansi * add a second layer for lighting controls * add in lighting support * add QMK Configurator support * use pragma once * remove un needed matrix.c * convert to GPIO methods * turn on rgblight_enable and get rid of custom matrix * set bootloadhid_bootloader to 1 * set bootmagic to lite and set it to k50 * add reset information to readme * use i2c_master instead of custom i2c * restore the custom i2c code * introduce reset key and eep_rst in function layer 1 * fix up pip3 install commands * fix up device and manufacturer names * remove un needed comments * add an ALL layout macro along with QMK Configurator support * move budget96 into donutcables directory since he actually has different boards * add a short donut cables blurb taken from his website * update readme for make instructions to point to the new path * Update keyboards/donutcables/budget96/config.h Co-Authored-By: mechmerlin <[email protected]> * Update keyboards/donutcables/budget96/readme.md Co-Authored-By: mechmerlin <[email protected]> * Update keyboards/donutcables/budget96/info.json Co-Authored-By: mechmerlin <[email protected]> * turn on backlight * Update keyboards/donutcables/budget96/readme.md Co-Authored-By: mechmerlin <[email protected]> * remove extra UART and BOOTLOADER settings that are not needed
mguterl · Apr 4, 2019 · f698f1e · f698f1e
1 parent 852d125
commit f698f1e
Show file tree

Hide file tree

Showing 13 changed files with 883 additions and 0 deletions.
diff --git a/keyboards/donutcables/budget96/budget96.c b/keyboards/donutcables/budget96/budget96.c
@@ -0,0 +1,80 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "budget96.h"
+
+#ifdef BACKLIGHT_ENABLE
+#include "backlight.h"
+#endif
+#ifdef RGBLIGHT_ENABLE
+#include "rgblight.h"
+#endif
+
+#include <avr/pgmspace.h>
+
+#include "action_layer.h"
+#include "i2c.h"
+#include "quantum.h"
+
+__attribute__ ((weak))
+void matrix_scan_user(void) {
+}
+
+#ifdef RGBLIGHT_ENABLE
+extern rgblight_config_t rgblight_config;
+
+void rgblight_set(void) {
+    if (!rgblight_config.enable) {
+        for (uint8_t i = 0; i < RGBLED_NUM; i++) {
+            led[i].r = 0;
+            led[i].g = 0;
+            led[i].b = 0;
+        }
+    }
+
+    i2c_init();
+    i2c_send(0xb0, (uint8_t*)led, 3 * RGBLED_NUM);
+}
+#endif
+
+void backlight_init_ports(void) {
+    // initialize pins D0, D1, D4 and D6 as output
+    setPinOutput(D0);
+    setPinOutput(D1);
+    setPinOutput(D4);
+    setPinOutput(D6);
+
+     // turn RGB LEDs on
+    writePinHigh(D0);
+    writePinHigh(D1);
+    writePinHigh(D4);
+    writePinHigh(D6);
+}
+
+ void backlight_set(uint8_t level) {
+	if (level == 0) {
+        // turn RGB LEDs off
+        writePinLow(D0);
+        writePinLow(D1);
+        writePinLow(D4);
+        writePinLow(D6);
+	} else {
+        // turn RGB LEDs on
+        writePinHigh(D0);
+        writePinHigh(D1);
+        writePinHigh(D4);
+        writePinHigh(D6);
+	}
+ }
diff --git a/keyboards/donutcables/budget96/budget96.h b/keyboards/donutcables/budget96/budget96.h
@@ -0,0 +1,56 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+#define LAYOUT_all( \
+    k50, k52, k53, k54, k55, k60, k6A, k7A, k70, k5B, k5C, k5D, k5E, k1D, k2E, k0D, k76, k79, k78, \
+    k40, k41, k42, k43, k44, k45, k61, k6B, k7B, k71, k4A, k4B, k4C, k4D, k4E, k46, k47, k48, k49, \
+    k30, k31, k32, k33, k34, k35, k62, k6C, k7C, k72, k3A, k3B, k3C, k3D, k36, k37, k38, k39,      \
+    k20, k21, k22, k23, k24, k25, k63, k6D, k7D, k73, k2A, k2B, k2C, k2D, k26, k27, k28, k29,      \
+    k10, k03, k11, k12, k13, k14, k15, k64, k6E, k7E, k74, k1A, k1B, k68, k16, k17, k18, k19,      \
+    k00, k01, k02, k65, k75, k0A, k0B, k66, k67, k69, k06, k08, k09                                \
+) \
+{ \
+    { k00, k01,   k02, k03, KC_NO, KC_NO, k06,   KC_NO, k08,   k09,   k0A,   k0B, KC_NO, k0D, KC_NO }, \
+    { k10, k11,   k12, k13, k14,   k15,   k16,   k17,   k18,   k19,   k1A,   k1B, KC_NO, k1D, KC_NO }, \
+    { k20, k21,   k22, k23, k24,   k25,   k26,   k27,   k28,   k29,   k2A,   k2B, k2C,   k2D, k2E },   \
+    { k30, k31,   k32, k33, k34,   k35,   k36,   k37,   k38,   k39,   k3A,   k3B, k3C,   k3D, KC_NO }, \
+    { k40, k41,   k42, k43, k44,   k45,   k46,   k47,   k48,   k49,   k4A,   k4B, k4C,   k4D, k4E },   \
+    { k50, KC_NO, k52, k53, k54,   k55,   KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, k5B, k5C,   k5D, k5E },   \
+    { k60, k61,   k62, k63, k64,   k65,   k66,   k67,   k68,   k69,   k6A,   k6B, k6C,   k6D, k6E },   \
+    { k70, k71,   k72, k73, k74,   k75,   k76,   KC_NO, k78,   k79,   k7A,   k7B, k7C,   k7D, k7E },   \
+}
+
+#define LAYOUT_96_ansi( \
+    k50, k52, k53, k54, k55, k60, k6A, k7A, k70, k5B, k5C, k5D, k5E, k1D, k2E, k0D, k76, k79, k78, \
+    k40, k41, k42, k43, k44, k45, k61, k6B, k7B, k71, k4A, k4B, k4C, k4E, k46, k47, k48, k49,      \
+    k30, k31, k32, k33, k34, k35, k62, k6C, k7C, k72, k3A, k3B, k3C, k3D, k36, k37, k38, k39,      \
+    k20, k21, k22, k23, k24, k25, k63, k6D, k7D, k73, k2A, k2B, k2D, k26, k27, k28, k29,           \
+    k10,      k11, k12, k13, k14, k15, k64, k6E, k7E, k74, k1A, k1B, k68, k16, k17, k18,           \
+    k00, k01, k02, k65, k75, k0B, k66, k67, k69, k06, k08, k09                                     \
+) \
+{ \
+    { k00, k01,   k02, KC_NO, KC_NO, KC_NO, k06,   KC_NO, k08,   k09,   KC_NO, k0B, KC_NO, k0D,   KC_NO }, \
+    { k10, k11,   k12, k13,   k14,   k15,   k16,   k17,   k18,   KC_NO, k1A,   k1B, KC_NO, k1D,   KC_NO }, \
+    { k20, k21,   k22, k23,   k24,   k25,   k26,   k27,   k28,   k29,   k2A,   k2B, KC_NO, k2D,   k2E },   \
+    { k30, k31,   k32, k33,   k34,   k35,   k36,   k37,   k38,   k39,   k3A,   k3B, k3C,   k3D,   KC_NO }, \
+    { k40, k41,   k42, k43,   k44,   k45,   k46,   k47,   k48,   k49,   k4A,   k4B, k4C,   KC_NO, k4E },   \
+    { k50, KC_NO, k52, k53,   k54,   k55,   KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, k5B, k5C,   k5D,   k5E },   \
+    { k60, k61,   k62, k63,   k64,   k65,   k66,   k67,   k68,   k69,   k6A,   k6B, k6C,   k6D,   k6E },   \
+    { k70, k71,   k72, k73,   k74,   k75,   k76,   KC_NO, k78,   k79,   k7A,   k7B, k7C,   k7D,   k7E },   \
+}
diff --git a/keyboards/donutcables/budget96/config.h b/keyboards/donutcables/budget96/config.h
@@ -0,0 +1,47 @@
+/*
+Copyright 2017 Luiz Ribeiro <[email protected]>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+#define VENDOR_ID       0x20A0
+#define PRODUCT_ID      0x422D
+#define MANUFACTURER    DonutCables
+#define PRODUCT         budget96
+
+#define RGBLED_NUM 16
+
+#define MATRIX_ROWS 8
+#define MATRIX_COLS 15
+
+#define MATRIX_COL_PINS { A0, A1, A2, A3, A4, A5, A6, A7, C7, C6, C5, C4, C3, C2, D7 }
+#define MATRIX_ROW_PINS { B0, B1, B2, B3, B4, B5, B6, B7 }
+#define UNUSED_PINS
+
+#define DIODE_DIRECTION COL2ROW
+#define DEBOUNCING_DELAY 5
+
+#define NO_BACKLIGHT_CLOCK
+#define BACKLIGHT_LEVELS 1
+#define RGBLIGHT_ANIMATIONS
+
+// Set bootmagic lite key to the key commonly programmed as Esc. 
+#define BOOTMAGIC_LITE_ROW 5
+#define BOOTMAGIC_LITE_COLUMN 0 
+
+/* key combination for command */
diff --git a/keyboards/donutcables/budget96/i2c.c b/keyboards/donutcables/budget96/i2c.c
@@ -0,0 +1,106 @@
+/*
+Copyright 2016 Luiz Ribeiro <[email protected]>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+// Please do not modify this file
+
+#include <avr/io.h>
+#include <util/twi.h>
+
+#include "i2c.h"
+
+void i2c_set_bitrate(uint16_t bitrate_khz) {
+    uint8_t bitrate_div = ((F_CPU / 1000l) / bitrate_khz);
+    if (bitrate_div >= 16) {
+        bitrate_div = (bitrate_div - 16) / 2;
+    }
+    TWBR = bitrate_div;
+}
+
+void i2c_init(void) {
+    // set pull-up resistors on I2C bus pins
+    PORTC |= 0b11;
+
+    i2c_set_bitrate(400);
+
+    // enable TWI (two-wire interface)
+    TWCR |= (1 << TWEN);
+
+    // enable TWI interrupt and slave address ACK
+    TWCR |= (1 << TWIE);
+    TWCR |= (1 << TWEA);
+}
+
+uint8_t i2c_start(uint8_t address) {
+    // reset TWI control register
+    TWCR = 0;
+
+    // begin transmission and wait for it to end
+    TWCR = (1<<TWINT) | (1<<TWSTA) | (1<<TWEN);
+    while (!(TWCR & (1<<TWINT)));
+
+    // check if the start condition was successfully transmitted
+    if ((TWSR & 0xF8) != TW_START) {
+        return 1;
+    }
+
+    // transmit address and wait
+    TWDR = address;
+    TWCR = (1<<TWINT) | (1<<TWEN);
+    while (!(TWCR & (1<<TWINT)));
+
+    // check if the device has acknowledged the READ / WRITE mode
+    uint8_t twst = TW_STATUS & 0xF8;
+    if ((twst != TW_MT_SLA_ACK) && (twst != TW_MR_SLA_ACK)) {
+        return 1;
+    }
+
+    return 0;
+}
+
+void i2c_stop(void) {
+    TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTO);
+}
+
+uint8_t i2c_write(uint8_t data) {
+    TWDR = data;
+
+    // transmit data and wait
+    TWCR = (1<<TWINT) | (1<<TWEN);
+    while (!(TWCR & (1<<TWINT)));
+
+    if ((TWSR & 0xF8) != TW_MT_DATA_ACK) {
+        return 1;
+    }
+
+    return 0;
+}
+
+uint8_t i2c_send(uint8_t address, uint8_t *data, uint16_t length) {
+    if (i2c_start(address)) {
+        return 1;
+    }
+
+    for (uint16_t i = 0; i < length; i++) {
+        if (i2c_write(data[i])) {
+            return 1;
+        }
+    }
+
+    i2c_stop();
+
+    return 0;
+}
diff --git a/keyboards/donutcables/budget96/i2c.h b/keyboards/donutcables/budget96/i2c.h
@@ -0,0 +1,24 @@
+/*
+Copyright 2016 Luiz Ribeiro <[email protected]>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+// Please do not modify this file
+
+#pragma once
+
+void i2c_init(void);
+void i2c_set_bitrate(uint16_t bitrate_khz);
+uint8_t i2c_send(uint8_t address, uint8_t *data, uint16_t length);
diff --git a/keyboards/donutcables/budget96/info.json b/keyboards/donutcables/budget96/info.json
@@ -0,0 +1,16 @@
+{
+    "keyboard_name": "budget96", 
+    "url": "", 
+    "maintainer": "qmk", 
+    "width": 19, 
+    "height": 6, 
+    "layouts": {
+        "LAYOUT_all": {
+            "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":15, "y":0}, {"x":16, "y":0}, {"x":17, "y":0}, {"x":18, "y":0}, {"x":0, "y":1}, {"x":1, "y":1}, {"x":2, "y":1}, {"x":3, "y":1}, {"x":4, "y":1}, {"x":5, "y":1}, {"x":6, "y":1}, {"x":7, "y":1}, {"x":8, "y":1}, {"x":9, "y":1}, {"x":10, "y":1}, {"x":11, "y":1}, {"x":12, "y":1}, {"x":13, "y":1}, {"x":14, "y":1}, {"x":15, "y":1}, {"x":16, "y":1}, {"x":17, "y":1}, {"x":18, "y":1}, {"x":0, "y":2, "w":1.5}, {"x":1.5, "y":2}, {"x":2.5, "y":2}, {"x":3.5, "y":2}, {"x":4.5, "y":2}, {"x":5.5, "y":2}, {"x":6.5, "y":2}, {"x":7.5, "y":2}, {"x":8.5, "y":2}, {"x":9.5, "y":2}, {"x":10.5, "y":2}, {"x":11.5, "y":2}, {"x":12.5, "y":2}, {"x":13.5, "y":2, "w":1.5}, {"x":15, "y":2}, {"x":16, "y":2}, {"x":17, "y":2}, {"x":18, "y":2}, {"x":0, "y":3, "w":1.75}, {"x":1.75, "y":3}, {"x":2.75, "y":3}, {"x":3.75, "y":3}, {"x":4.75, "y":3}, {"x":5.75, "y":3}, {"x":6.75, "y":3}, {"x":7.75, "y":3}, {"x":8.75, "y":3}, {"x":9.75, "y":3}, {"x":10.75, "y":3}, {"x":11.75, "y":3}, {"x":12.75, "y":3}, {"x":13.75, "y":3, "w":1.25}, {"x":15, "y":3}, {"x":16, "y":3}, {"x":17, "y":3}, {"x":18, "y":3}, {"x":0, "y":4, "w":1.25}, {"x":1.25, "y":4}, {"x":2.25, "y":4}, {"x":3.25, "y":4}, {"x":4.25, "y":4}, {"x":5.25, "y":4}, {"x":6.25, "y":4}, {"x":7.25, "y":4}, {"x":8.25, "y":4}, {"x":9.25, "y":4}, {"x":10.25, "y":4}, {"x":11.25, "y":4}, {"x":12.25, "y":4, "w":1.75}, {"x":14, "y":4}, {"x":15, "y":4}, {"x":16, "y":4}, {"x":17, "y":4}, {"x":18, "y":4}, {"x":0, "y":5, "w":1.25}, {"x":1.25, "y":5, "w":1.25}, {"x":2.5, "y":5, "w":1.25}, {"x":3.75, "y":5, "w":6.25}, {"x":10, "y":5}, {"x":11, "y":5}, {"x":12, "y":5}, {"x":13, "y":5}, {"x":14, "y":5}, {"x":15, "y":5}, {"x":16, "y":5}, {"x":17, "y":5}, {"x":18, "y":5}]
+        },
+
+        "LAYOUT_96_ansi": {
+            "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":15, "y":0}, {"x":16, "y":0}, {"x":17, "y":0}, {"x":18, "y":0}, {"x":0, "y":1}, {"x":1, "y":1}, {"x":2, "y":1}, {"x":3, "y":1}, {"x":4, "y":1}, {"x":5, "y":1}, {"x":6, "y":1}, {"x":7, "y":1}, {"x":8, "y":1}, {"x":9, "y":1}, {"x":10, "y":1}, {"x":11, "y":1}, {"x":12, "y":1}, {"x":13, "y":1, "w":2}, {"x":15, "y":1}, {"x":16, "y":1}, {"x":17, "y":1}, {"x":18, "y":1}, {"x":0, "y":2, "w":1.5}, {"x":1.5, "y":2}, {"x":2.5, "y":2}, {"x":3.5, "y":2}, {"x":4.5, "y":2}, {"x":5.5, "y":2}, {"x":6.5, "y":2}, {"x":7.5, "y":2}, {"x":8.5, "y":2}, {"x":9.5, "y":2}, {"x":10.5, "y":2}, {"x":11.5, "y":2}, {"x":12.5, "y":2}, {"x":13.5, "y":2, "w":1.5}, {"x":15, "y":2}, {"x":16, "y":2}, {"x":17, "y":2}, {"x":18, "y":2}, {"x":0, "y":3, "w":1.75}, {"x":1.75, "y":3}, {"x":2.75, "y":3}, {"x":3.75, "y":3}, {"x":4.75, "y":3}, {"x":5.75, "y":3}, {"x":6.75, "y":3}, {"x":7.75, "y":3}, {"x":8.75, "y":3}, {"x":9.75, "y":3}, {"x":10.75, "y":3}, {"x":11.75, "y":3}, {"x":12.75, "y":3, "w":2.25}, {"x":15, "y":3}, {"x":16, "y":3}, {"x":17, "y":3}, {"x":18, "y":3}, {"x":0, "y":4, "w":2.25}, {"x":2.25, "y":4}, {"x":3.25, "y":4}, {"x":4.25, "y":4}, {"x":5.25, "y":4}, {"x":6.25, "y":4}, {"x":7.25, "y":4}, {"x":8.25, "y":4}, {"x":9.25, "y":4}, {"x":10.25, "y":4}, {"x":11.25, "y":4}, {"x":12.25, "y":4, "w":1.75}, {"x":14, "y":4}, {"x":15, "y":4}, {"x":16, "y":4}, {"x":17, "y":4}, {"x":0, "y":5, "w":1.25}, {"x":1.25, "y":5, "w":1.25}, {"x":2.5, "y":5, "w":1.25}, {"x":3.75, "y":5, "w":6.25}, {"x":10, "y":5, "w":1.5}, {"x":11.5, "y":5, "w":1.5}, {"x":13, "y":5}, {"x":14, "y":5}, {"x":15, "y":5}, {"x":16, "y":5}, {"x":17, "y":5}, {"x":18, "y":4, "h":2}]
+        }
+    }
+}
diff --git a/keyboards/donutcables/budget96/keymaps/default/config.h b/keyboards/donutcables/budget96/keymaps/default/config.h
@@ -0,0 +1,19 @@
+/* Copyright 2018 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here
diff --git a/keyboards/donutcables/budget96/keymaps/default/keymap.c b/keyboards/donutcables/budget96/keymaps/default/keymap.c
@@ -0,0 +1,35 @@
+/* Copyright 2018 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+[0] = LAYOUT_96_ansi(\
+      KC_ESC,   KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,    KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_PSCR, KC_NLCK, KC_INS,  KC_HOME, KC_PGUP, KC_PSLS, \
+      KC_GRV,   KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,     KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC, KC_END,  KC_PGDN, KC_PSLS, KC_PAST,          \
+      KC_TAB,   KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,     KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS, KC_P7,   KC_P8,   KC_P9,   KC_PMNS,          \
+      KC_CAPS,  KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,     KC_L,    KC_SCLN, KC_QUOT, KC_ENT,  KC_P4,   KC_P5,   KC_P6,   KC_PPLS,                   \
+      KC_LSFT,  KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM,  KC_DOT,  KC_SLSH, KC_RSFT, KC_UP,   KC_P1,   KC_P2,   KC_P3,                              \
+      KC_LCTL,  KC_LGUI, KC_LALT, KC_SPC,  KC_RALT, MO(1),   KC_LEFT, KC_DOWN, KC_RIGHT, KC_P0,   KC_PDOT, KC_PENT),                                                               \
+
+[1] = LAYOUT_96_ansi(\
+      RESET,   EEP_RST,  KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,  KC_TRNS, KC_TRNS, KC_TRNS, \
+      BL_TOGG, BL_STEP,  BL_ON,   BL_OFF,  BL_INC,  BL_DEC,  BL_BRTG, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,           \
+      RGB_TOG, RGB_MOD,  RGB_HUI, RGB_SAI, RGB_VAI, RGB_SPI, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,           \
+      KC_TRNS, RGB_RMOD, RGB_HUD, RGB_SAD, RGB_VAD, RGB_SPD, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                    \
+      KC_TRNS, KC_TRNS,  KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,                             \
+      KC_TRNS, KC_TRNS,  KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),                                                                \
+};
+
diff --git a/keyboards/donutcables/budget96/keymaps/default/readme.md b/keyboards/donutcables/budget96/keymaps/default/readme.md
@@ -0,0 +1 @@
+# The default keymap for budget96