tty: remove redundant 'default n' from Kconfig-s

'default n' is the default value for any bool or tristate Kconfig setting so there is no need to write it explicitly. Also since commit f467c56 ("kconfig: only write '# CONFIG_FOO is not set' for visible symbols") the Kconfig behavior is the same regardless of 'default n' being present or not: ... One side effect of (and the main motivation for) this change is making the following two definitions behave exactly the same: config FOO bool config FOO bool default n With this change, neither of these will generate a '# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied). That might make it clearer to people that a bare 'default n' is redundant. ... Signed-off-by: Bartlomiej Zolnierkiewicz <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
michelpromonet · Apr 16, 2019 · f692f77 · f692f77
1 parent 7a7457b
commit f692f77
Show file tree

Hide file tree

Showing 3 changed files with 0 additions and 8 deletions.
diff --git a/drivers/tty/Kconfig b/drivers/tty/Kconfig
@@ -84,7 +84,6 @@ config HW_CONSOLE
 config VT_HW_CONSOLE_BINDING
        bool "Support for binding and unbinding console drivers"
        depends on HW_CONSOLE
-       default n
        ---help---
          The virtual terminal is the device that interacts with the physical
          terminal through console drivers. On these systems, at least one
@@ -313,7 +312,6 @@ config N_GSM
 config TRACE_ROUTER
 	tristate "Trace data router for MIPI P1149.7 cJTAG standard"
 	depends on TRACE_SINK
-	default n
 	help
 	  The trace router uses the Linux tty line discipline framework to
 	  route trace data coming from a tty port (say UART for example) to
@@ -329,7 +327,6 @@ config TRACE_ROUTER
 
 config TRACE_SINK
 	tristate "Trace data sink for MIPI P1149.7 cJTAG standard"
-	default n
 	help
 	  The trace sink uses the Linux line discipline framework to receive
 	  trace data coming from the trace router line discipline driver

diff --git a/drivers/tty/hvc/Kconfig b/drivers/tty/hvc/Kconfig
@@ -25,7 +25,6 @@ config HVC_CONSOLE
 config HVC_OLD_HVSI
 	bool "Old driver for pSeries serial port (/dev/hvsi*)"
 	depends on HVC_CONSOLE
-	default n
 
 config HVC_OPAL
 	bool "OPAL Console support"
@@ -74,7 +73,6 @@ config HVC_UDBG
        bool "udbg based fake hypervisor console"
        depends on PPC
        select HVC_DRIVER
-       default n
        help
          This is meant to be used during HW bring up or debugging when
 	 no other console mechanism exist but udbg, to get you a quick

diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
@@ -370,7 +370,6 @@ config SERIAL_MAX310X
 	depends on SPI_MASTER
 	select SERIAL_CORE
 	select REGMAP_SPI if SPI_MASTER
-	default n
 	help
 	  This selects support for an advanced UART from Maxim (Dallas).
 	  Supported ICs are MAX3107, MAX3108, MAX3109, MAX14830.
@@ -653,7 +652,6 @@ config SERIAL_MUX_CONSOLE
 config PDC_CONSOLE
 	bool "PDC software console support"
 	depends on PARISC && !SERIAL_MUX && VT
-	default n
 	help
 	  Saying Y here will enable the software based PDC console to be 
 	  used as the system console.  This is useful for machines in 
@@ -1110,7 +1108,6 @@ config SERIAL_QE
 	depends on QUICC_ENGINE
 	select SERIAL_CORE
 	select FW_LOADER
-	default n
 	help
 	  This driver supports the QE serial ports on Freescale embedded
 	  PowerPC that contain a QUICC Engine.