Merge tag 'devicetree-fixes-for-6.6-1' of git://git.kernel.org/pub/sc…

…m/linux/kernel/git/robh/linux

Pull more devicetree updates from Rob Herring:
 "A couple of conversions which didn't get picked up by the subsystems
  and one fix:

   - Convert st,stih407-irq-syscfg and Omnivision OV7251 bindings to DT
     schema

   - Merge Omnivision OV5695 into OV5693 binding

   - Fix of_overlay_fdt_apply prototype when !CONFIG_OF_OVERLAY"

* tag 'devicetree-fixes-for-6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  dt-bindings: irqchip: convert st,stih407-irq-syscfg to DT schema
  media: dt-bindings: Convert Omnivision OV7251 to DT schema
  media: dt-bindings: Merge OV5695 into OV5693 binding
  of: overlay: Fix of_overlay_fdt_apply prototype when !CONFIG_OF_OVERLAY

Documentation/devicetree/bindings/i2c/qcom,i2c-cci.yaml

@@ -269,6 +269,7 @@ examples:
                 port {
                     ov7251_ep: endpoint {
                         data-lanes = <0 1>;
+                        link-frequencies = /bits/ 64 <240000000 319200000>;
                         remote-endpoint = <&csiphy3_ep>;
                     };
                 };

Documentation/devicetree/bindings/interrupt-controller/st,stih407-irq-syscfg.yaml

@@ -0,0 +1,65 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/interrupt-controller/st,stih407-irq-syscfg.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics STi System Configuration Controlled IRQs
+
+maintainers:
+  - Patrice Chotard <[email protected]>
+
+description:
+  On STi based systems; External, CTI (Core Sight), PMU (Performance
+  Management), and PL310 L2 Cache IRQs are controlled using System
+  Configuration registers.  This device is used to unmask them prior to use.
+
+properties:
+  compatible:
+    const: st,stih407-irq-syscfg
+
+  st,syscfg:
+    description: Phandle to Cortex-A9 IRQ system config registers
+    $ref: /schemas/types.yaml#/definitions/phandle
+
+  st,irq-device:
+    description: Array of IRQs to enable.
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    items:
+      - description: Enable the IRQ of the channel one.
+      - description: Enable the IRQ of the channel two.
+
+  st,fiq-device:
+    description: Array of FIQs to enable.
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    items:
+      - description: Enable the IRQ of the channel one.
+      - description: Enable the IRQ of the channel two.
+
+  st,invert-ext:
+    description: External IRQs can be inverted at will. This property inverts
+      these three IRQs using bitwise logic, each one being encoded respectively
+      on the first, second and fourth bit.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 1, 2, 3, 4, 5, 6 ]
+
+required:
+  - compatible
+  - st,syscfg
+  - st,irq-device
+  - st,fiq-device
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq-st.h>
+    irq-syscfg {
+        compatible    = "st,stih407-irq-syscfg";
+        st,syscfg     = <&syscfg_cpu>;
+        st,irq-device = <ST_IRQ_SYSCFG_PMU_0>,
+                        <ST_IRQ_SYSCFG_PMU_1>;
+        st,fiq-device = <ST_IRQ_SYSCFG_DISABLED>,
+                        <ST_IRQ_SYSCFG_DISABLED>;
+    };
+...

Documentation/devicetree/bindings/media/i2c/ovti,ov5693.yaml

@@ -5,26 +5,41 @@
 $id: http://devicetree.org/schemas/media/i2c/ovti,ov5693.yaml#
 $schema: http://devicetree.org/meta-schemas/core.yaml#
 
-title: Omnivision OV5693 CMOS Sensor
+title: Omnivision OV5693/OV5695 CMOS Sensors
 
 maintainers:
   - Tommaso Merciai <[email protected]>
 
 description: |
-  The Omnivision OV5693 is a high performance, 1/4-inch, 5 megapixel, CMOS
-  image sensor that delivers 2592x1944 at 30fps. It provides full-frame,
+  The Omnivision OV5693/OV5695 are high performance, 1/4-inch, 5 megapixel, CMOS
+  image sensors that deliver 2592x1944 at 30fps. It provides full-frame,
   sub-sampled, and windowed 10-bit MIPI images in various formats via the
   Serial Camera Control Bus (SCCB) interface.
 
-  OV5693 is controlled via I2C and two-wire Serial Camera Control Bus (SCCB).
-  The sensor output is available via CSI-2 serial data output (up to 2-lane).
+  OV5693/OV5695 are controlled via I2C and two-wire Serial Camera Control Bus
+  (SCCB). The sensor output is available via CSI-2 serial data output (up to
+  2-lane).
 
 allOf:
   - $ref: /schemas/media/video-interface-devices.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: ovti,ov5693
+    then:
+      properties:
+        port:
+          properties:
+            endpoint:
+              required:
+                - link-frequencies
 
 properties:
   compatible:
-    const: ovti,ov5693
+    enum:
+      - ovti,ov5693
+      - ovti,ov5695
 
   reg:
     maxItems: 1
@@ -34,6 +49,9 @@ properties:
       System input clock (aka XVCLK). From 6 to 27 MHz.
     maxItems: 1
 
+  clock-names:
+    const: xvclk
+
   dovdd-supply:
     description:
       Digital I/O voltage supply, 1.8V.
@@ -72,7 +90,6 @@ properties:
 
         required:
           - data-lanes
-          - link-frequencies
 
 required:
   - compatible

Documentation/devicetree/bindings/media/i2c/ovti,ov7251.yaml

@@ -0,0 +1,109 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov7251.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: OmniVision OV7251 Image Sensor
+
+description:
+  The Omnivision OV7251 is a 1/7.5-Inch CMOS active pixel digital image sensor
+  with an active array size of 640H x 480V. It is programmable through a serial
+  I2C interface.
+
+maintainers:
+  - Todor Tomov <[email protected]>
+
+properties:
+  compatible:
+    const: ovti,ov7251
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    description: XCLK Input Clock
+
+  clock-names:
+    const: xclk
+
+  clock-frequency:
+    description: Frequency of the xclk clock in Hz.
+
+  vdda-supply:
+    description: Analog voltage supply, 2.8 volts
+
+  vddd-supply:
+    description: Digital core voltage supply, 1.2 volts
+
+  vdddo-supply:
+    description: Digital I/O voltage supply, 1.8 volts
+
+  enable-gpios:
+    maxItems: 1
+    description:
+      Reference to the GPIO connected to the XSHUTDOWN pin, if any. Polarity
+      is GPIO_ACTIVE_HIGH.
+
+  port:
+    description: Digital Output Port
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml#
+        unevaluatedProperties: false
+
+        properties:
+          clock-lanes:
+            maximum: 1
+
+          data-lanes:
+            maxItems: 1
+
+          link-frequencies: true
+
+        required:
+          - data-lanes
+          - link-frequencies
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - vdddo-supply
+  - vdda-supply
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        camera@3c {
+            compatible = "ovti,ov7251";
+            reg = <0x3c>;
+            clocks = <&clks 1>;
+            clock-frequency = <24000000>;
+            vdddo-supply = <&ov7251_vdddo_1v8>;
+            vdda-supply = <&ov7251_vdda_2v8>;
+            vddd-supply = <&ov7251_vddd_1v5>;
+            enable-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+
+            port {
+                ov7251_ep: endpoint {
+                    remote-endpoint = <&csi0_ep>;
+                    clock-lanes = <1>;
+                    data-lanes = <0>;
+                    link-frequencies = /bits/ 64 <240000000 319200000>;
+                };
+            };
+        };
+    };
+...

Documentation/devicetree/bindings/media/rockchip-isp1.yaml

@@ -199,6 +199,7 @@ examples:
             wcam: camera@36 {
                 compatible = "ovti,ov5695";
                 reg = <0x36>;
+                clocks = <&cru SCLK_TESTCLKOUT1>;
 
                 port {
                     wcam_out: endpoint {

include/linux/of.h

@@ -1676,8 +1676,8 @@ int of_overlay_notifier_unregister(struct notifier_block *nb);
 
 #else
 
-static inline int of_overlay_fdt_apply(void *overlay_fdt, u32 overlay_fdt_size,
-				       int *ovcs_id)
+static inline int of_overlay_fdt_apply(const void *overlay_fdt, u32 overlay_fdt_size,
+				       int *ovcs_id, struct device_node *target_base)
 {
 	return -ENOTSUPP;
 }